EN
Linear logo
Official user manual

Linear Digital Video Recorder (DVS-2400)

44 pages·2.6 MB·Digital Video Recorder·PDF·ENDEFRITNLJA
Linear Digital Video Recorder (DVS-2400)
Table of Contents 80 sections SECURITY · SUPERVISED WIRELESS SECURITY CONSOLE · Installation & Programming Instructions · (760) 438-7000 • FAX (760) 438-7043 · … ShowHide
SECURITYp.1SUPERVISED WIRELESS SECURITY CONSOLEp.1Installation & Programming Instructionsp.1(760) 438-7000 • FAX (760) 438-7043p.1INTRODUCTIONp.2DXS-32 DOOR/WINDOWp.4DXS-31 DOOR/WINDOWp.4DXS-81 BILL TRAPp.4DXS-54p.4DXS-91 GLASS BREAK DETECTORp.4DXS-72 SMOKE DETECTORp.4SENSORp.4PIRp.4DXS-32p.5DXS-31p.5DXT-21 DXS-21p.5DXT-23 DXS-23p.5DXS-62 DXS-63p.5DXS-81p.5DXT-41p.5DXT-42p.5DXT-61p.5DXS-91p.52. SECURITY SYSTEM FLOOR PLANp.6EXAMPLE SYSTEMp.6DESIGN THE INSTALLATIONp.6ESp.6MD MS Sp.6GBp.6WKp.6LIVINGp.6ENTRYp.6KITCHENp.6CONp.6BEDp.6DININGp.6MSp.6S MSp.6SDp.6BATH DENp.6GARAGEp.6MDp.6◆ Sensor mounts on door or window with adjacentp.7magnet. ◆ Opening door or window moves magnet away,p.7triggering sensor. ◆ Internal lithium batteries are monitored by thep.7◆ For controlling the system without having to gop.7to the Console. ◆ Emergency and fire alarm can be triggered fromp.7Console. ◆ Keypad’s beeper will buzz during transmissionsp.7ABOUT SENSOR STATUS SUPERVISIONp.74. CONSOLE FEATURESp.83 MODE INDICATORSp.84 CONSOLE STATUS INDICATORSp.8POWER LIGHTp.8BATTERIES LIGHTp.8TROUBLE LIGHTp.85 SIREN SPEAKERp.82 MODE BUTTONSp.8OFFp.86 STATUS INDICATORSp.8CHIMEp.87 CASE ACCESS SCREW (HIDDEN)p.88 KEYPADp.8TESTp.810 AUXILIARY FUSEp.917 WIRING ACCESS HOLEp.918 WALL-MOUNT SLOTSp.911 MAIN TERMINAL BLOCKp.919 RADIO TEST POINTSp.920 MICROPHONE (WITH MODEL VB-2 INSTALLED ONLY)p.912 BATTERY FUSEp.921 ANNUNCIATOR VOLUME CONTROLp.913 TELEPHONE TERMINAL BLOCKp.922 DIGITAL VOICE SYNTHESIS MODULE (OPTIONAL)p.914 INTERNAL SPEAKER CONNECTORp.915 ANTENNA TERMINALSp.916 OPTIONAL BACKUP BATTERYp.95. CONSOLE INSTALLATIONp.10CONSOLE LOCATIONp.10✍ NOTE: Sensor signals must be able to reach thep.10REMOVE CASE LOCKING SCREW TO ACCESS INTERNAL COMPONENTSp.10
Page 1 of the Linear Digital Video Recorder (DVS-2400) user manual — (760) 438-7000 • FAX (760) 438-7043
Page 1 · click to enlarge
Page 1
Linear Digital Video Recorder (DVS-2400) — SECURITY diagram (page 1)
Fig. 1

SECURITY

SUPERVISED WIRELESS SECURITY CONSOLE

Linear Digital Video Recorder (DVS-2400) — SECURITY diagram (page 1)
Fig. 2

Installation & Programming Instructions

(760) 438-7000 • FAX (760) 438-7043

www.linearcorp.com

Page 2 of the Linear Digital Video Recorder (DVS-2400) user manual — INTRODUCTION
Page 2 · click to enlarge
Page 2

INTRODUCTION

CONGRATULATIONS for selecting Linear’s DVS-2400 Security System. The DVS-2400 Console incorporates many advanced and sophisticated features. The system can be expanded and customized to fit the installation’s specific needs.

Linear Digital Video Recorder (DVS-2400) — INTRODUCTION diagram (page 2)
Fig. 3

The DVS-2400 Console and its accessories are designed and manufactured by the oldest wireless security company in North America. You can look ahead to many years of reliable service with this Console and its accessories.

Many insurance companies offer discounts on homeowners and renters policies when a security system is installed. Discount credits vary with different companies and generally increase in savings with an increase in the level of protection. Inform the user to ask their insurance agent about savings available.

In this manual, the bullets preceding the text help to define the step. For example:

◆This symbol indicates a feature.

This symbol indicates an action to perform and provides a box to check when the action is completed. ❇This symbol is for lit indications or system

sounds. ✍This symbol is for important notes.

Page 3 of the Linear Digital Video Recorder (DVS-2400) user manual — INTRODUCTION
Page 3 · click to enlarge
Page 3
Page 3 of the Linear Digital Video Recorder (DVS-2400) user manual — INTRODUCTION
Page 4 of the Linear Digital Video Recorder (DVS-2400) user manual — DXS-32 DOOR/WINDOW
Page 4 · click to enlarge
Page 4
Linear Digital Video Recorder (DVS-2400) — DXS-32 DOOR/WINDOW diagram (page 4)
Fig. 4

DXS-32 DOOR/WINDOW

DXS-31 DOOR/WINDOW

DXS-81 BILL TRAP

DXS-54

DXS-91 GLASS BREAK DETECTOR

DXS-72 SMOKE DETECTOR

SENSOR

SENSOR

PIR

CONSOLE The DVS-2400 Console is the heart of the system. It monitors all of the system’s wireless sensors and controls the alarm sirens.

capability at the Central Station through the communicator, local human voice prompts from the Console’s speaker, and voice prompted remote system control using in-house or off-site pushbutton telephones. The economy Model VB-3 is the same as the VB-2 without 2-way Central Station audio capability.

The Console constantly monitors the condition of the system’s sensors, displaying which protected doors and windows are open or closed. If an alarm occurs, the Console displays which sensor(s) caused it. When a sensor has a low battery, the Console displays which sensor needs a new battery. Sensors that send hourly status transmissions keep the Console informed of their operating condition.

The Console has 24-hour capabilities that are always ready to operate, even when the Console is disarmed. They can be triggered by buttons on the Console, the Wireless Keypad, portable remote controls and smoke detectors. Pressing the [EMERGENCY] or [FIRE] button for two seconds will cause an immediate siren and call the central station. IMPORTANT: For personal emergency use only.

Up to eight different custom user codes can be used to operate the system. For security, a user code must be entered to disarm (turn off) the system. The system can be armed (turned on) by entering a user code, or with the unique “Quick Arm” feature. The five restricted user codes and the special page alert user code can only arm and disarm the system, no programming changes are allowed. The master user code is allowed to program the Console, and a duress code can be selected for emergency disarming of the system with a duress report to the Central Station. The page alert user code can dial a pager number to inform the pager wearer when the Console is disarmed.

The Console’s Environmental feature is active 24-hours and can be triggered with sensors connected to devices such as water flow detectors, over/under temperature sensors, flood sensors, toxic gas detectors, etc. The Environmental feature activates the chime annunciator without sounding the siren. The Environmental feature does not send communicator reports.

An Automation Output in the Console provides an easy way to connect external devices to the Console. The output is fully programmable to activate on a variety of conditions, such as when the system is armed, during alarms, and during exit/entry delays. The Automation Output can connect to lighting control modules, relays, noisemakers, and indicators. The Console’s and wireless keypad’s (A) key and transmitters can control the Automation Output.

The Console’s memory will retain the user codes and all of the system’s programming, even during a total power loss. An optional backup battery can be installed to power the system during short power failures.

The built-in digital communicator connects the Console to a Central Alarm Monitoring Station through the telephone. With a monitored system, the central station can dispatch authorities in case of burglary, fire or other emergency. The central station can also call family, friends, neighbors, or anyone else designated on a custom call list.

The Console can be programmed locally using its own keypad or remotely, over the telephone, using Linear’s Model RA-2400 Remote Access software program. The RA-2400 upload/download program is a Windows application that runs on a personal computer and communicates with the Console through a modem, connected directly to the Console or through the telephone line.

Each sensor can report directly to the Central Station using the digital communicator’s Point ID feature. If a sensor triggers an alarm or experiences supervisory trouble, a unique report code can be sent for immediate identification of the event.

The optional Models VB-2 or VB-3 digital voice synthesis modules can be installed in the Console. The VB-2 module provides three exciting features: 2-way audio monitoring

Page 5 of the Linear Digital Video Recorder (DVS-2400) user manual — DXS-54
Page 5 · click to enlarge
Page 5

DOOR/WINDOW SENSORS The DXS-31 & DXS-32 sensors monitor doors and windows. They send radio signals to the Console. One type of signal is sent when the door or window is opened, and a different type of signal is sent when the door or window is closed. If the Console is armed, a sensor can trigger the Console’s burglary siren when its door or window is opened. Both sensors are supervised, and send hourly status reports and monitor battery condition.

PANIC BUTTONS The DXT-21, DXS-21 single-button and DXT-23 and DXS-23 two-button transmitters can be used as portable “panic buttons”. Pressing the front or top button on the DXT-21, DXS-21 at any time will trigger the emergency siren. Pressing both front buttons simultaneously on the DXT-23 & DXS-23 at any time will trigger the emergency siren. These transmitters can be programmed to activate various other Console functions. The DXT-21 and DXT-23 transmitters are not supervised. The DXS-21 and DXS-23 transmitters are supervised.

DXS-32

DXS-31

WIRELESS KEYPAD The DXS-10 wireless keypad is used to control the Console remotely. It can be placed in a convenient spot so the user doesn’t have to go to the Console to control the system. The wireless keypad can also trigger the emergency or fire siren and actuate the Automation Output. Pressing the [∗] key will cause the Console to sound beeps corresponding to the current operating mode. The DXS-10 is supervised, it sends hourly status reports and monitors its battery condition.

DXT-21 DXS-21

DXT-23 DXS-23

The DXS-62 and DXS-63 transmitters can be used as portable “panic buttons”. Pressing the single button on the DXS-62, or pressing both buttons on the DXS-63, at any time will trigger the emergency siren. These supervised transmitters send hourly status signals and low battery signals if the battery is low.

Linear Digital Video Recorder (DVS-2400) — DXT-21 DXS-21 diagram (page 5)
Fig. 5

DXS-62 DXS-63

SMOKE DETECTORS The DXS-72 is a high quality smoke detector with a built-in radio transmitter. As soon as smoke is detected, the unit will sound its local noisemaker. Then, 20 seconds after the local noisemaker sounds, the transmitter sends an alarm signal to the Console. The alarm signal will be repeated every 20 seconds as long as smoke is still present. A restoral signal will be sent when the smoke detection chamber clears. The DXS-72 is supervised, and sends hourly status reports and monitors battery condition.

BILL TRAP The DXS-81 bill trap can be used with the Console in small commercial hold-up installations. The unit is concealed in a cash drawer under a stack of currency, with a single “bait” bill secured in its money clip. During a hold-up, the cashier removes the stack of currency along with the “bait” bill. When a “bait” bill is removed, the transmitter sends a signal to the Console. Four additional signals are sent within the first minute after the “bait” bill is removed. When the “bait” bill is replaced, a restore signal is sent. The DXS-81 is supervised, it can send hourly status reports (optional) and monitors its battery condition.

Linear Digital Video Recorder (DVS-2400) — DXS-62 DXS-63 diagram (page 5)
Fig. 6

REMOTE CONTROLS The DXT-41, DXT-61 single-button and DXT-23, DXT-42 multi-button remote controls can be used to remotely arm and disarm the Console. The DXT-42’s left button will arm and the right button will disarm the Console. Pressing both buttons simultaneously on the DXT-42 will trigger the emergency siren. Alternately, the console can be programmed to respond to the DXT-42 by arming and disarming with the left button, and activating the automation output with the right button. Each transmitter can be programmed to activate various other Console functions. These transmitters are not supervised.

DXS-81

PASSIVE INFRARED MOTION DETECTOR The DXS-54 is a passive infrared (PIR) motion detector with a built-in radio transmitter. The PIR detects motion in its detection pattern by measuring the infrared emission levels of objects that it “sees”. If the infrared levels change quickly, as when a person moves across the detection pattern, the PIR will recognize the change as an intrusion and send an alarm signal to the Console. An alarm will be triggered if the Console is in the Away Mode. The DXS-54 is supervised, it sends hourly status reports and monitors its battery condition.

DXT-41

DXT-42

DXT-61

GLASS BREAK DETECTOR The DXS-91 is a glass break detector with an audio sound discriminator and a built-in radio transmitter. The unit “listens” for the sound of breaking glass. When glass breakage is detected, the unit sends an alarm signal to the Console. The DXS-91 is supervised, it sends hourly status reports and monitors its battery condition.

DXS-54

DXS-91

Page 6 of the Linear Digital Video Recorder (DVS-2400) user manual — MD
Page 6 · click to enlarge
Page 6

2. SECURITY SYSTEM FLOOR PLAN

EXAMPLE SYSTEM

◆The example shows a typical DVS-2400 system. ◆Any or all of the accessories shown can be used. ◆A total of 24 sensors (including keypads) can be

used with each Console.

DESIGN THE INSTALLATION

Create a floor plan of the installation. Consider the security needs of the premises. Determine which doors and windows are vulnerable to intrusion. Figure which interior areas an intruder might go to if unlawful entrance is gained. Indicate locations for door/window sensors, interior motion detectors, keypads, glass break detectors and external siren speakers. Decide on a centralized location for the security Console.

ES

MD MS S

GB

S

CON - CONSOLE S - DOOR/WINDOW SENSOR WK - WIRELESS KEYPAD MD - MOTION DETECTOR ES - EXTERNAL SIREN SD - SMOKE DETECTOR GB - GLASS BREAK SENSOR MS - EXTERNAL MAGNETIC SWITCH

WK

LIVING

ENTRY

S

S

KITCHEN

CON

S

BED

DINING

S

MS

S MS

SD

BED

BATH DEN

S

S

GB

GARAGE

MD

Example Residential Security System Floor Plan

Page 7 of the Linear Digital Video Recorder (DVS-2400) user manual — ABOUT SENSOR STATUS SUPERVISION
Page 7 · click to enlarge
Page 7
Linear Digital Video Recorder (DVS-2400) — ◆ Sensor mounts on door or window with adjacent diagram (page 7)
Fig. 7 · ◆ Sensor mounts on door or window with adjacent

◆ Sensor mounts on door or window with adjacent

magnet. ◆ Opening door or window moves magnet away,

triggering sensor. ◆ Internal lithium batteries are monitored by the

Console. ◆Sends hourly status reports to the Console. ◆Up to 3 years battery life (depends on frequency

◆ For controlling the system without having to go

to the Console. ◆ Emergency and fire alarm can be triggered from

wireless keypad at any time. ◆Green operation light. ◆Internal 9-volt battery is monitored by the

Linear Digital Video Recorder (DVS-2400) — ◆ For controlling the system without having to go diagram (page 7)
Fig. 8 · ◆ For controlling the system without having to go

Console. ◆ Keypad’s beeper will buzz during transmissions

when the battery is low. ◆Up to 3 years battery life (depends on frequency

of activation). ◆Sends hourly status reports to the Console. ◆Press the [(A)] key to activate the automation

output. ◆Pressing [∗] clears the keypad. ◆Holding [∗] for two seconds sounds the mode

beeps from the Console.

✔Off Mode: 1 “Gong” ✔Chime Mode: 1 “Gong” & 1 “Beep”. ✔Home Mode: 1 “Gong” & 2 “Beeps”. ✔Away Mode: 1 “Gong” & 3 “Beeps”. ✔Test Mode: 1 “Bing” & 4 “Beeps”.

ABOUT SENSOR STATUS SUPERVISION

All DXS Format sensors transmit hourly status reports. All DXT Format sensors do not transmit hourly status reports. Both sensor formats can be used with the Console. When a sensor is programmed into the Console, the Console will set the sensor as non-supervised or supervised. Sensors set as non-supervised are not expected to send hourly status reports. Sensors set as supervised are expected to send hourly status reports. If a status report is not received in 8 hours from a sensor set as supervised, the TROUBLE indicator will flash. When sensors are programmed into the Console, ALL STATIONARY SENSORS ARE SET AS SUPERVISED, ALL PORTABLE SENSORS ARE SET AS NON-SUPERVISED.

If stationary DXT Format sensors have been programmed into the Console, be sure to change their setting to non-supervised to prevent TROUBLE indications. This will not prevent low battery monitoring.

If portable DXS Format sensors have been programmed into the Console, and the installation requires supervision for specific portable sensor(s), change the selected portable sensors setting to supervised.

After programming the sensors, if changes are required, refer to “Changing a Sensors Supervision” on Page 26 for details on changing the way a sensor’s supervision is set.

Page 8 of the Linear Digital Video Recorder (DVS-2400) user manual — TEST
Page 8 · click to enlarge
Page 8

4. CONSOLE FEATURES

3 MODE INDICATORS

Linear Digital Video Recorder (DVS-2400) — 3 MODE INDICATORS diagram (page 8)
Fig. 9

★Specific indicator will light showing the mode the Console is in. ★HOME indicator will blink during secure exit and home instant modes. ★AWAY indicator will blink during the exit delay in the Away Mode.

4 CONSOLE STATUS INDICATORS

★Show the current status of the Console.

POWER LIGHT

★Glows when AC power is on. ★Dims when AC power is off and backup battery is installed. ★Blinks when the backup battery is low, recharging or missing. ★Off when AC power is off and no backup battery is installed (system

disabled).

BATTERIES LIGHT

★Blinks when one or more sensors has a low battery. ★Press [∗] key for two seconds to view sensor status. Sensor status indicator

for any sensor with a low battery will light along with the BATTERIES indicator. ★Switch to Test Mode after replacing the sensor battery and completely test

the system (see Test Mode). Switching to Test Mode clears the low battery indication.

TROUBLE LIGHT

★Blinks when one or more sensors have not reported status during the eight

1 24-HOUR BUTTONS ★Pressing the [FIRE] button for two seconds sounds the fire siren and sends

hour status time window. ★Press [∗] key for two seconds to view sensor status. Sensor status indicator

a “fire” message to a central monitoring station through the digital communicator (if the system is monitored). ★Pressing the [EMERGENCY] button for two seconds sounds the

for any sensor that has not reported in will light along with the TROUBLE indicator. ★Switch to Test Mode after servicing the sensor and completely test the

emergency siren and sends an “emergency” message to a central monitoring station through the digital communicator (if the system is monitored). ★Both work even when system is disarmed. ★IMPORTANT: For personal emergency use only.

system (see Test Mode). Switching to Test Mode clears the trouble indication.

5 SIREN SPEAKER

★Makes unique sounds for burglary, fire and emergencies. ★Alarm sirens stop automatically after five minutes. ★Sounds advisory tones to confirm keystrokes from the Console. ★Sounds mode selections tones. ★Sounds alarm memory tones. ★Beeps when Automation Output is activated. ★Speaks the system status information when optional VB-2 or VB-3 digital

2 MODE BUTTONS

★Used to control the Console.

OFF

★Off Mode disarms the system. ★Switching to Off Mode stops the alarm siren.

✔Multiple beeps sound and status lights flash if an alarm has occurred. ☞Multiple beeps mean caution. AN INTRUDER MAY STILL BE PRESENT.

voice synthesis module is installed. ★Terminals available for an external siren.

6 STATUS INDICATORS

CHIME

★Indicates the status of each of the system’s sensors. ★Lights show which doors and windows are open. ★Lights flash to display sensors that have caused an alarm. ★Stick-on labels are provided to identify the custom sensor locations.

★Chime Mode disarms the system. ★Switching to Chime Mode stops the alarm siren.

✔Multiple beeps sound and status lights flash if an alarm has occurred. ☞Multiple beeps mean caution. AN INTRUDER MAY STILL BE PRESENT. ★Chime Mode is for monitoring doors and windows.

7 CASE ACCESS SCREW (HIDDEN)

✔Use this mode as an “automatic door chime” when at home. ✔Opening any protected door or window causes Console to “ding-dong”.

★Remove clear display window and sensor identification card to gain access

to the screw. ★Remove case access screw to unlock case. Case hinges open to the left.

★Home Mode arms the perimeter sensors, but not the interior sensors.

8 KEYPAD

✔Use this mode when anyone is staying behind. ✔Interior motion detectors and interior door sensors are not armed. ✔Home secure mode makes all delayed perimeter sensors instant. ✔Secure exit mode starts an exit delay while remaining in Home Mode. ✔Re-entering during the exit delay restarts the exit delay (one time only).

★Backlit keys for easy viewing in low light conditions. ★For entering the user’s user code (numerically or alphabetically). ★Used when programming system options. ★Press [(A)] key to activate Automation Output. ★Press the [∗] key to clear keypad if the wrong key is pressed. ★Press and hold the [∗] key for one second to view sensor battery and

supervisory status (see BATTERIES and TROUBLE indicator description).

★Away Mode arms the entire system.

✔Use this mode when leaving home. ✔Door sensors set for “delayed” will have a delay that allows you to leave

and enter the premises without sounding the alarm. ✔Re-entering during the exit delay restarts the exit delay (one time only). ✔Entry Delay beeps warn you to disarm the system before the siren starts.

TEST

★Test Mode is for testing the system sensors.

✔All sensor status lights blink when the Test Mode is entered. ✔Each sensor status light will stop blinking when its sensor is tested. ★Hold the [TEST] button down to test all of the Console’s indicator lights.

Page 9 of the Linear Digital Video Recorder (DVS-2400) user manual — 16 OPTIONAL BACKUP BATTERY
Page 9 · click to enlarge
Page 9
Linear Digital Video Recorder (DVS-2400) — 10 AUXILIARY FUSE diagram (page 9)
Fig. 10

10 AUXILIARY FUSE

17 WIRING ACCESS HOLE

★Type 2AG, 1-amp fuse. ★Protects the external relay output when used with wet contacts (12 VDC

★Provides access to recessed wiring trough in base of Console. ★Route cables for power, telephone, external speaker, etc. through this hole. ★Loop for zip-tie strain relief provided next to hole.

switched out). ★Fuse will blow when load exceeds 1 amp. ✍WARNING: For continued protection against the risk of fire, replace

18 WALL-MOUNT SLOTS

★Used when mounting Console recessed in the wall. ★Two mounting brackets (supplied) slide through slots and are retained by

only with the same type and rating of fuse.

11 MAIN TERMINAL BLOCK

screws, clamping the unit to the wall.

★Terminals for connection to the plug-in AC transformer. ★Terminals for connection to an external speaker. ★Automation Output to connect to an automation controller. ★External relay output for “wet” contacts (switched 12 volts) or “dry” contacts

19 RADIO TEST POINTS

★Used to monitor the Console’s radio receiver during troubleshooting. ★Provides connection for an audio amplifier to listen to the receiver’s output. ★Helpful to determine sources of radio interference.

(normally open 1 amp @ 24 volts maximum).

20 MICROPHONE (WITH MODEL VB-2 INSTALLED ONLY)

12 BATTERY FUSE

★High sensitivity microphone. ★Detects room audio when communicator is reporting to the Central Station

★Type 2AG, 3-amp fuse for the backup battery. ★If the POWER light is flashing and the optional backup battery is installed

in 2-way audio mode (Model VB-2 digital voice synthesis module must be installed).

and charged, check this fuse. ✍WARNING: For continued protection against the risk of fire, replace

21 ANNUNCIATOR VOLUME CONTROL

only with the same type and rating of fuse.

★Varies the volume of the advisory tones that come from the speaker. ★Does not affect internal or external sirens (they are always full volume).

13 TELEPHONE TERMINAL BLOCK

★Provides telephone connections for the digital communicator. ★Provides telephone connection for voice prompted telephone remote control

22 DIGITAL VOICE SYNTHESIS MODULE (OPTIONAL)

★Two voice synthesis modules are available, the Model VB-2 and VB-3. ★Both modules allow remote command of the Console using a standard

(optional VB-2 digital voice synthesis module required). ★Provides seized ring and tip connections for local telephone instruments.

pushbutton telephone, on or off site. ★Both modules provide optional human voice prompts from the Console’s

Communicator will disconnect local telephones while on-line.

14 INTERNAL SPEAKER CONNECTOR

speaker. ★The Model VB-2 gives the Console’s digital communicator listen-only,

★Connects the internal speaker to the Console circuit board. ★2-pin connector, non-polarized.

manual 2-way and full duplex 2-way audio capability with the Central Station.

15 ANTENNA TERMINALS

★Antenna and ground terminals for receiving signals from the system’s

sensors. ★Pre-wired to the Console’s internal wire dipole antenna. ★Alternately connects to the Model LA-P local whip and remote antenna kit.

16 OPTIONAL BACKUP BATTERY

★Space for 12-volt, 1.2 amp/hour backup battery. (Highly recommended.) ★Backup battery is automatically charged and monitored by the Console. ★Backup battery can power the Console for up to 6 hours.

Page 10 of the Linear Digital Video Recorder (DVS-2400) user manual — WALL MOUNTING
Page 10 · click to enlarge
Page 10

5. CONSOLE INSTALLATION

CONSOLE LOCATION

✍ NOTE: Sensor signals must be able to reach the

Linear Digital Video Recorder (DVS-2400) — CONSOLE LOCATION diagram (page 10)
Fig. 11

Console.

✔Try to centrally locate the Console. ✔Keep Console away from large metal

appliances. ✔Maximum recommended sensor range is

USE A PAPER CLIP TO REMOVE THE CLEAR DISPLAY WINDOW

400 feet (system tested at 1000 feet). ✍NOTE: If you don’t use the Wireless Keypad, the

Console should be easily accessible to the usual entrance.

✔When the Console is set in the Away Mode,

the user has 30 seconds to switch to Off Mode before the burglary siren sounds. ✍NOTE: Make sure the Console is in a place where

Linear Digital Video Recorder (DVS-2400) — CONSOLE LOCATION diagram (page 10)
Fig. 12

REMOVE CASE LOCKING SCREW TO ACCESS INTERNAL COMPONENTS

the alarm can be heard during the night hours.

✔Optional remote external sirens (up to 150

feet from the Console) can be used to make alarms louder and remote their location. Locate the Console near an AC power outlet that’s not controlled by a light switch. Locate the Console near a telephone outlet (if using the digital communicator).

CASE LOCKING SCREW

◆ To access the Console’s internal components or

Linear Digital Video Recorder (DVS-2400) — CASE LOCKING SCREW diagram (page 10)
Fig. 13

to prepare the Console for wall mounting, the case locking screw needs removing. Use a paper clip to remove the clear plastic display window. Remove the sensor number nameplate. Remove the case locking screw.

CUT A 10" x 6 3/4" HOLE CENTERED BETWEEN STUDS IN MOUNTING WALL AT A CONVENIENT HEIGHT

WALL MOUNTING

◆ If desired, the Console can be surface mounted

or recessed into the wall. Surface Mounting

For surface mounting, use the Console’s case bottom as a template and mark the locations for the four mounting screws. Use four screws and appropriate screw anchors to temporarily mount the unit to the wall (the unit will need to be removed to complete the recessed wiring hook up). Recessed Mounting

Linear Digital Video Recorder (DVS-2400) — WALL MOUNTING diagram (page 10)
Fig. 14

For recessed wall mounting, cut a 10" by 6-3/4" hole, centered between studs, in the mounting wall at a convenient height. Slide the unit into the mounting hole and temporarily secure it with the two retaining clamps and screws provided (the unit will need to be removed to complete the recessed wiring hook up).

Linear Digital Video Recorder (DVS-2400) — WALL MOUNTING diagram (page 10)
Fig. 15

SECURE CONSOLE TO WALL USING THE TWO CLAMPS AND SCREWS PROVIDED

Page 11 of the Linear Digital Video Recorder (DVS-2400) user manual — EXTERNAL ALARM SIREN CONNECTION (OPTIONAL)
Page 11 · click to enlarge
Page 11
Linear Digital Video Recorder (DVS-2400) — 5. CONSOLE INSTALLATION diagram (page 11)
Fig. 16

EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL)

◆ An external console speaker sounds system

tones and alerts occupants with a loud siren during alarm. ◆With the VB-2 module installed, the Central

Station can talk to the occupants through the external console speaker. ◆Use an 8-ohm, 10 watt minimum rated speaker.

Do not use a horn/siren with a built-in siren driver. ◆Up to two 8-ohm speakers can be used with

AC AC EXT. SPKR (-) H/A - H/A + RELAY N.O. RELAY DRY

each Console. ◆Up to 150 feet of 22 AWG wire can be used with

JUMPER FOR EXT. SPEAKERS OPTIONAL VOICE MODULE MODEL: VB-2 OR VB-3

each speaker. Mount the external speaker. Route the speaker wires from the external speaker to the Console. Open the Console top cover and locate the main terminal block. Route the speaker wires up through the wiring access hole. Remove the wire jumper from the EXT. SPKR & (-) terminals. Connect the speaker wires to the EXT. SPKR & (-) terminals. ✍NOTE: If connecting two external speakers,

connect the second speaker in parallel, to the same EXT. SPKR & (-) terminals as the first speaker. The system tone volume can be adjusted with the annunciator volume control.

CONNECT SPEAKER LEADS TO EXT. SPKR & (-) TERMINALS

Linear Digital Video Recorder (DVS-2400) — EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL) diagram (page 11)
Fig. 17

EXTERNAL ALARM SIREN CONNECTION (OPTIONAL)

◆ An external siren alerts occupants and neighbors

with a loud siren during alarm. ◆Use a 12 volt, 1 amp maximum rated

weather-resistant horn speaker with a built-in siren driver. Do not use a plain speaker. ✍NOTE: Connection of an electromechanical bell or

motor bell is not recommended because of the radio interference generated when the bell is running. Mount the external siren. Route the wires from the external siren to the Console. Open the Console top cover and locate the main terminal strip. Route the siren wires up through the wiring access hole. Connect the siren wires to the RELAY N.O. & (-) terminals. ✍NOTE: By removing the Console’s auxiliary fuse,

AC AC EXT. SPKR (-) H/A - H/A + RELAY N.O. RELAY DRY

the relay contacts will become isolated. Use the RELAY N.O. & RELAY DRY terminals to switch an externally powered load.

CONNECT SIREN LEADS TO (-) & RELAY N.O. TERMINALS

Page 12 of the Linear Digital Video Recorder (DVS-2400) user manual — POWER SOURCE
Page 12 · click to enlarge
Page 12

TELEPHONE LINE CONNECTION (OPTIONAL)

Linear Digital Video Recorder (DVS-2400) — TELEPHONE LINE CONNECTION (OPTIONAL) diagram (page 12)
Fig. 18

◆ Connect the Console to the telephone line if the

TELEPHONE

TERMINAL

system is monitored, requires 2-way audio, or requires telephone remote command. ◆Telephone ring & tip terminals are for connection

to the incoming telephone line. ◆Seized telephone ring & tip are for connection to

local telephone sets. When the communicator activates, all the local telephone sets will be disconnected to prevent an off-hook telephone on the premises from blocking the communicator call. Install a USOC RJ31-X or RJ38-X jack to the telephone system near the Console. Route an appropriate modular telephone line cord from the jack to the Console. Route the line cord through the Console’s wiring access hole. Connect the incoming telephone line wires to the Console’s telephone terminal block TIP and RING terminals. ◆Connect the local telephone set wires to the

SEIZED RING (R1) SEIZED TIP (T1)

LINE RING (R) LINE TIP (T)

Linear Digital Video Recorder (DVS-2400) — SEIZED RING (R1) SEIZED TIP (T1) diagram (page 12)
Fig. 19
8-POSITIO USOC RJ31 (OR RJ38- JACK

T R R1 T1 SHORTING BAR SHORT REMOVED ON PLUG INSERTION

Console’s telephone terminal block SEIZED TIP and SEIZED RING terminals. ◆When directly connecting (without a telephone

line) to the DVS-2400 with the RA-2400 remote access software (Version 1.3 or later), disconnect the incoming telephone line and connect the modem to the panel’s TIP and RING terminals (with the modem’s red & green phone line wires). Press the [EMERGENCY] key while in Test Mode to cause the panel to connect to the modem.

CONNECT TELEPHONE LINE TO THE TELEPHONE TERMINAL BLOCK

AUTOMATION OUTPUT CONNECTION (OPTIONAL)

◆ The Console provides a Automation Output to

control lights, devices and appliances. ◆Automation Output can connect to most popular

Linear Digital Video Recorder (DVS-2400) — CONNECT TELEPHONE LINE TO THE TELEPHONE TERMINAL BLOCK diagram (page 12)
Fig. 20

MINUS H/A TERMINAL WILL SWITCH TO GROUND WHEN AUTOMATION OUTPUT IS ACTIVATED

home automation devices and other simple electronic devices (see Figure). Press [(A)] to turn the Automation Output on, press [(A)] again to turn it off. Programmable Options

AC AC EXT. SPKR (-) H/A - H/A + RELAY N.O. RELAY DRY

MAIN TERMINAL

BLOCK

◆ There are many programmable options for the

Automation Output. ◆ The Automation Output can be programmed for

POSITIVE H/A TERMINAL PROVIDES +12 VOLTS DC AND IS CURRENT LIMITED AT 30 MILLIAMPS MAXIMUM

a variety of useful functions, such as: flashing during alarm, flashing after an alarm, on while armed, or, on during exit/entry delays. ◆See the “Advanced Programming” section of this

EXAMPLE AUTOMATION OUTPUT HOOK-UPS

X-10 BURGLAR ALARM INTERFACE (CAN CONTROL HOUSE LIGHTS THROUGH X-10 SYSTEM)

LINEAR RB-90 RELAY MODULE YOUR LOAD

LIGHT EMITTING DIODE (L.E.D.)

manual for details on changing the function of the Automation Output.

POWER SOURCE

H/A + H/A - H/A + H/A - H/A + H/A -

Page 13 of the Linear Digital Video Recorder (DVS-2400) user manual — BACKUP BATTERY INSTALLATION (OPTIONAL)
Page 13 · click to enlarge
Page 13

CONSOLE POWER CONNECTION

Linear Digital Video Recorder (DVS-2400) — CONSOLE POWER CONNECTION diagram (page 13)
Fig. 21

◆ The Console is powered by a low voltage plug-in

transformer. ◆ Use up to 25 feet of 20 AWG or larger

AC AC EXT. SPKR (-) H/A - H/A + RELAY N.O. RELAY DRY

two-conductor wire to connect the transformer to the Console. Route the power wires from the plug-in transformer to the Console. Connect the wires to the transformer terminals (do not plug the transformer in until the wiring is complete). Route the power wires through the Console’s wiring access hole. Connect the power wires from the transformer to the Console’s main terminal block AC & AC terminals. Secure all of the wires entering the Console with a zip-tie to the Console’s strain relief loop. Plug transformer into an unswitched AC outlet. Secure transformer with screw to prevent un-plugging.

MAIN TERMINAL

BLOCK

Linear Digital Video Recorder (DVS-2400) — MAIN TERMINAL diagram (page 13)
Fig. 22

CONNECT TRANSFORMER LEADS TO AC POWER TERMINALS

Linear Digital Video Recorder (DVS-2400) — CONNECT TRANSFORMER LEADS TO AC POWER TERMINALS diagram (page 13)
Fig. 23

PLUG TRANSFORMER INTO AC POWER OUTLET THAT IS NOT CONTROLED BY A LIGHT SWITCH

BACKUP BATTERY INSTALLATION (OPTIONAL)

◆ A 12 volt backup battery may be installed and is

highly recommended. ◆ The backup battery will power the Console for

Linear Digital Video Recorder (DVS-2400) — BACKUP BATTERY INSTALLATION (OPTIONAL) diagram (page 13)
Fig. 24

up to 6 hours during AC power loss. ◆The backup battery is automatically charged by

the Console when AC power is present. ◆A low backup battery will cause the Console

POWER indicator to flash as it is being charged. To install the battery, slide the battery between the retaining clamps and under the battery holder. Position the battery until the clamps snap in place. The battery terminals should be facing the center of the Console case bottom. Connect the black battery lead to the black battery terminal. Connect the red battery lead to the red battery terminal. ✍WARNING: DO NOT REVERSE THE BATTERY

CONNECT RED BATTERY LEAD TO RED TERMINAL CONNECT BLACK BATTERY LEAD TO BLACK TERMINAL

Linear Digital Video Recorder (DVS-2400) — BACKUP BATTERY INSTALLATION (OPTIONAL) diagram (page 13)
Fig. 25

LEADS! THE BATTERY FUSE WILL BLOW.

Page 14 of the Linear Digital Video Recorder (DVS-2400) user manual — PROGRAM THE SENSORS INTO THE CONSOLE’S MEMORY
Page 14 · click to enlarge
Page 14

6. BASIC CONSOLE PROGRAMMING

◆ In a new installation, when power is first applied

the Console’s master user code is “1234”.

CREATE THE MASTER USER CODE

✍ NOTE: Local programming must be entered on the

Console’s keypad, not on a wireless remote keypad. Press [∗] (clears keypad if any other keys have been pressed). Place the Console in Test Mode (enter 1234 and press [TEST]. ❇A “gong” and four “beeps” will sound.

ENTERING

SETTING A NEW MASTER

SETUP

MODE

USER CODE

Linear Digital Video Recorder (DVS-2400) — ENTERING diagram (page 14)
Fig. 26
Linear Digital Video Recorder (DVS-2400) — ENTERING diagram (page 14)
Fig. 27

Enter the Setup Mode from Test Mode, enter 1234 then press [TEST] again. ❇A “gong” and five “beeps” will sound. You are

now in Setup Mode. Enter 99 then press [HOME]. Enter any combination of 1-5 digits for the master user code, then press [AWAY]. ✍NOTE: For maximum security, a three to five digit

code is recommended. Press and hold the [OFF] key for 3 seconds to exit program mode. Test the new master user code by entering it then pressing [TEST]. Log the master user code in the box below.

MASTER USER CODE

✍ NOTE: The master user code can be used to enter

Setup Mode. The restricted user codes cannot. To create restricted user codes, see the “Advanced Programming” section of this manual.

PROGRAM THE SENSORS INTO THE CONSOLE’S MEMORY

◆ Each wireless sensor that is going to be used

with the Console must be programmed into the Console’s memory. Start with the Console in Test Mode (enter any user code and press [TEST]). Enter the Setup Mode from Test Mode, enter the master user code then press [TEST] again. ❇A “gong” and five “beeps” will sound. You are

Linear Digital Video Recorder (DVS-2400) — PROGRAM THE SENSORS INTO THE CONSOLE’S MEMORY diagram (page 14)
Fig. 28

now in Setup Mode. ❇The sensor status indicators will light for any

sensors programmed into the Console. Enter an unused sensor number from 01-24 (you must enter two digits, example: 5 = 05) ❇The sensor indicator light will flash for the sensor

number selected. Activate the sensor by sending a test or alarm signal (be sure the sensor’s battery is connected or that its battery protection strip is removed). ❇A single “bing” tone will sound and the sensor

status indicator for that sensor will stay lit. Enter another sensor number or exit Setup Mode by holding the [OFF] key for three seconds.

Page 15 of the Linear Digital Video Recorder (DVS-2400) user manual — SEND SIGNAL WITH LEFT BUTTON
Page 15 · click to enlarge
Page 15

PROGRAMMING DIFFERENT SENSOR TYPES

◆ Follow the instructions on the previous page to

select a sensor number to program the sensor into. ✍NOTE: A sensor can be programmed into more

than one location. Be sure to choose an unused sensor number. If a sensor gets entered into more than one location, delete the duplicates using the remove sensor function. To add DXS-10 wireless keypads, press and hold the keypad’s [∗] key until programmed into the Console. ✍IMPORTANT NOTE: The DXS-31 & DXS-32

door/window sensors are pre-set at the factory for delayed burglary response. If the sensor is going to be used on a non-entry portal (window, sliding glass door, etc.) a jumper can be changed in the sensor to select instant response. The jumper should be changed before learning the sensor so the Console will program the sensor to the proper function. See the “Basic Sensor Installation” section of this manual for details on changing the jumper. For DXS-31 and DXS-32 door/window sensors, move the magnet away from the side of the sensor. For DXS-81, DXS-91, DXS-54, & DXS-72 accessory sensors, simply send a test transmission (refer to the sensor’s instructions for details on sending a test transmission). For DXT-61, DXT-21, DXS-21 & DXT-41 single-button remotes, simply press the unit’s button. The unit will function as an arm/disarm remote. ✍NOTE: After the Console “learns” the transmitter,

single-button remotes can easily be re-programmed as “panic buttons” or home automation controllers. Refer to Page 24 in the “Customizing the System” section of this manual. For DXT-23 & DXT-42 multi-button remotes: Learn the transmitter by pressing the left button. The remote will arm the Console with the left button and disarm with the right. Labels are provided with the DXT-42 for identifying the buttons. ✍NOTE: After the Console “learns” the transmitter,

SEND SIGNAL WITH LEFT BUTTON

multi-button remotes can easily be re-programmed to have the left button arm/disarm the Console and the right button activate/deactivate the Home Automation Output. Refer to Page 24 in the “Customizing the System” section of this manual. ❇A single “bing” tone will sound and the sensor

status indicator will stay lit when the sensor is learned by the Console. ❇A double “buzz” tone will sound if there is

LEFT = ARM RIGHT = DISARM BOTH = EMERGENCY

already another sensor programmed to that sensor number. Exit Setup Mode by holding the [OFF] button for two seconds. Reminder: The Console will automatically exit the Setup Mode and return to Off Mode after 3 minutes of keypad inactivity. ✍NOTE: To remove sensors from the Console’s

memory, see Page 22 in the “Customizing the System” section of this manual.

Page 16 of the Linear Digital Video Recorder (DVS-2400) user manual — ◆ Four anti-mar pads are provided as a scratch
Page 16 · click to enlarge
Page 16

7. BASIC SENSOR INSTALLATION

◆ Each accessory sensor is packaged with its own

Linear Digital Video Recorder (DVS-2400) — ◆ Each accessory sensor is packaged with its own diagram (page 16)
Fig. 29 · ◆ Each accessory sensor is packaged with its own

set of installation instructions specific to the model of sensor. ◆Refer to the sensor’s instructions for details on

FROM TOP OF CASE TWIST SCREWDRIVER BETWEEN CASE HALVES UNTIL IT POPS OPEN

installing, operating, and testing of the sensor. ◆Following are basic instructions for installing two

popular DVS-2400 accessories: The Model DXS-10 Wireless Remote Keypad and the Models DXS-31 & DXS-32 Door/Window Transmitters.

DXS-10 WIRELESS KEYPAD

◆ The DXS-10 is used to remotely command the

Console. ◆ The keypad can be simply set on a table or

mounted to a flat surface. TABLE-TOP USE

◆ Four anti-mar pads are provided as a scratch

deterrent for the keypad. ✍NOTE: Do not use the adhesive pads if the keypad

is going to be wall mounted. Peel off the adhesive tape backing on the pads and stick them to the back of the keypad. ◆The wireless keypad can be used as a portable

keypad. Because of the hourly supervisory transmissions, if the unit is taken out of range from the Console for more than eight hours, the Console will indicate “radio trouble” for the keypad. The keypad’s sensor number can be programmed for “non-supervised” if required. See the “Advanced Programming” section of this manual. WALL MOUNT USE

USE THE FOUR SCRATCH DETERRENT PADS PROVIDED FOR TABLE-TOP USE

Linear Digital Video Recorder (DVS-2400) — ◆ Four anti-mar pads are provided as a scratch diagram (page 16)
Fig. 30 · ◆ Four anti-mar pads are provided as a scratch

◆The wireless keypad can be wall mounted.

Open the keypad by inserting a small screwdriver in one of the top slots in the keypad case. Gently twist the screwdriver until the case pops open. Attach the rear case to the wall using the two screws provided. ✍NOTE: For best signal transmission, the keypad

should be mounted at least three feet above ground level. Hook the top edge of the keypad case together and snap the keypad onto the rear case. ✍WARNING: The wireless keypad is designed for

ATTACH REAR CASE TO WALL WITH THE TWO SCREWS PROVIDED

indoor use only.

MOUNT AT A CONVENIENT LOCATION NEAR PRIMARY ENTRY/EXIT DOOR

Page 17 of the Linear Digital Video Recorder (DVS-2400) user manual — TEST SENSORS
Page 17 · click to enlarge
Page 17

DXS-31 & DXS-32 DOOR/WINDOW SENSORS

EXAMPLE INSTALLATIONS

◆ The DXS-31 and DXS-32 sensors can be used to

(WITH DXS-31 SHOWN)

Linear Digital Video Recorder (DVS-2400) — DXS-31 & DXS-32 DOOR/WINDOW SENSORS diagram (page 17)
Fig. 31

monitor doors, windows, cabinets, crawl space doors, gates, freezer doors, and many other moving objects that could be used for intrusion or need to be monitored. ◆A built-in magnetic switch triggers the sensor

when its magnet (mounted on the moving part or the door or window) moves away from the sensor. ◆External normally closed switches (DXS-31

only) can be wired to the sensor for remote triggering. ◆The door/window sensor (DXS-31 only) can

connect directly to a glass break detector. SET SENSOR JUMPER

INSTANT/DELAY OPTION JUMPER

ANTENNA

◆ A jumper inside the door/window sensor selects

INPUT SELECT JUMPER

MAGNET ALIGNMENT MARK

TWO TYPE 2032 BATTERIES

instant or delayed response. If the sensor is going to be used on the primary entry/exit door make sure that the jumper is in the DELAY position. If the sensor is going to be used on a window or a door that is not going to be used to enter and exit the premises, set the jumper to the INSTANT position. APPLY DOUBLE-STICK TAPE

BATTERY CLAMP SCREW

TRANSMIT INDICATOR

BATTERY CLAMP

TEST SWITCH

EXTERNAL INPUT TERMINALS

INSTANT/DELAY OPTION JUMPER

SELECTS INSTANT

Apply double-stick tape (supplied) to back of sensors and magnets. ◆Screws are also provided to mount sensors and

magnets. ◆ Screws are preferred over the double-stick tape

in permanent installations. ATTACH SENSORS AND MAGNETS

SELECTS DELAY

On doors, mount sensor to door frame and magnet to door. ✍NOTE: Magnet must line up with mark on sensor

ATTACH MOUNTING PLATES USING THE SCREWS OR DOUBLE-STICK TAPE PROVIDED

case both horizontally & vertically. Allow a maximum of 1/2" between magnet and sensor when door/window is closed. Snap sensor onto mounting plate. On windows, mount sensor to window frame and magnet to window. Snap sensor onto mounting plate. The magnet height is adjustable and an optional magnet spacer is provided for uneven surfaces.

Linear Digital Video Recorder (DVS-2400) — SELECTS DELAY diagram (page 17)
Fig. 32

TEST SENSORS

❇ Console in Chime Mode should “ding-dong”

Linear Digital Video Recorder (DVS-2400) — TEST SENSORS diagram (page 17)
Fig. 33

when the sensor sends signal. Open door or window. ❇Verify that light on the sensor glows momentarily

when door/window is opened. ❇Status indicator on Console should remain lit for

each door/window sensor that is left open.

Page 18 of the Linear Digital Video Recorder (DVS-2400) user manual — LABELING THE SENSORS
Page 18 · click to enlarge
Page 18

8. CUSTOMIZING THE CONSOLE

◆ The Console can be customized for the specific

Linear Digital Video Recorder (DVS-2400) — ◆ The Console can be customized for the specific diagram (page 18)
Fig. 34 · ◆ The Console can be customized for the specific

installation. ◆ A label sheet with sensor location names is

provided with the Console. ◆ Labeling the sensors allows quick and easy

identification of where any alarms have occurred, where a sensor with a low battery is, where a sensor with radio trouble is, etc.

LABELING THE SENSORS

Use a paper clip to remove the clear display window. Bend down the tabs on the sensor number card and fit it onto the Console. Open one protected door/window to light its sensor status light on the Console. Choose a label that describes the sensor location, or write the location on a blank label, and stick it in the area to the right of the sensor light. Close the protected opening that you just labeled. Repeat for each protected opening. Stick the WIRELESS KEYPAD label in the sensor number location for the wireless keypad (if used). Replace the clear display window when finished.

Linear Digital Video Recorder (DVS-2400) — LABELING THE SENSORS diagram (page 18)
Fig. 35

OPEN DOOR OR WINDOW TO LIGHT SENSOR STATUS INDICATOR ON CONSOLE

APPLY SENSOR IDENTIFICATION LABELS TO THE APPROPRIATE SENSOR LOCATIONS

Linear Digital Video Recorder (DVS-2400) — LABELING THE SENSORS diagram (page 18)
Fig. 36
Page 19 of the Linear Digital Video Recorder (DVS-2400) user manual — HOLD DOWN
Page 19 · click to enlarge
Page 19

9. CONSOLE OPERATING MODES

OFF MODE

◆ Use this mode to disarm the burglary portion of

the system. ◆ Switching to Off Mode stops any alarms in

OFF MODE

progress. ◆ The 24-hour functions are still active in Off Mode

START HERE

and can be triggered by pressing the [FIRE] or [EMERGENCY] button. Switch to Off Mode by entering the user code, and pressing [OFF]. ❇When the system is disarmed to Off Mode, the

(OPTIONAL)

YOUR USER CODE

Console will sound one “Gong”. ❇If an alarm has occurred, multiple beeps will

sound after disarming and the sensor light for the sensor(s) that caused the alarm will flash. ✍NOTE: In Off Mode, protected doors and windows

cannot trigger the burglary alarm.

1 GONG

OFF

DONE

CHIME MODE

START HERE

CHIME MODE

(OPTIONAL)

◆ Chime Mode is for monitoring entries and exits

without causing alarms. ◆ Use Chime Mode as an “automatic door chime”

when at home. ❇ Opening any protected door or window causes

YOUR USER CODE

the Console to sound a “ding-dong”. Select the Chime Mode by entering a user code, then press [CHIME]. The user can enter Chime Mode from Off Mode by holding down the [CHIME] key for two seconds. ❇When the system is switched to the Chime

1 GONG & 1 BEEP

CHIME

Mode, the Console will sound a “Gong” and one “Beep”. ◆Going to Chime Mode disarms the system and

DONE

OR

stops any alarms in progress. ✍NOTE: In Chime Mode, protected doors and

START IN OFF

windows cannot trigger the burglary alarm.

HOLD DOWN

CHIME

1 GONG & 1 BEEP

DONE

Page 20 of the Linear Digital Video Recorder (DVS-2400) user manual — DONE
Page 20 · click to enlarge
Page 20

HOME MODE

MANUAL BYPASSING OF SENSORS

◆ Use this mode when sleeping or when anyone is

◆ Manual bypassing of sensors in the Home Mode

staying inside. ◆ Home Mode causes an instant alarm when any

allows arming of the system at night with open windows, while still having perimeter protection with other closed doors and windows. ◆The Console will resist arming with open door or

perimeter sensor is triggered. ◆Home Mode causes a delayed alarm when any

window sensors. ❇ Four high-low beeps to warn the user that

exit/entry sensor is triggered (except in Home Instant Mode when they are instant). ◆Alarm siren stops automatically after five

something is open and the system will remain in the previous mode. ❇Lit sensor status indicators show which sensors

minutes and the system will remain armed. ◆Home Mode ignores all interior sensors (motion

detectors, etc.). Arm to Home Mode by entering a user code, and pressing [HOME]. The user can “Quick Arm” to Home Mode from Off or Chime Mode by holding down the [HOME] key for two seconds. (Quick arming can be disabled; see the “Advanced Programming” section of this manual.) ❇When the system is armed to the Home Mode,

are open. To manually bypass the open sensors, arm the system again within 5 seconds. ❇A “gong” and two “beeps” will sound, the HOME

indicator will light, and the open sensors will be bypassed. ✍WARNING: Bypassed sensors cannot cause an

alarm.

the Console will sound a “Gong” and two “Beeps”. Enter a user code and press [OFF] or [CHIME] to disarm from Home Mode and/or stop the alarm siren. ❇If an alarm has occurred, multiple beeps will sound

after disarming and the sensor light for the sensor(s) that caused the alarm will flash (switch to Off Mode again or re-arm the Console to stop the flashing alarm memory light).

HOME MODE

SECURE EXIT

START IN OFF OR CHIME MODE

START IN HOME MODE

SECURE EXIT

If the system is already in the Home Mode and the user wants to exit the premises while leaving someone inside with the system still in Home Mode, enter a user code and press the [HOME] key. ❇A “gong” and two “beeps” will sound and the

(OPTIONAL)

(OPTIONAL)

YOUR USER CODE

YOUR USER CODE

HOME light will blink for 60 seconds. No exit delay beeps will sound during the Exit Delay. ◆The user can leave through a door with a delayed

perimeter sensor during the 60 second Exit Delay without causing the Console to begin an Entry Delay. ◆Re-entering during the silent Exit Delay will

1 GONG & 2 BEEPS

1 GONG & 2 BEEPS

DONE

DONE

extend the Exit Delay another 60 seconds (one time only). ✍NOTE: The Exit Delay time can be changed; see

the “Advanced Programming” section of this manual.

HOME INSTANT

HOME INSTANT MODE

QUICK ARM

MODE

If the system is already in the Home Mode and the user wants to make all exit/entry sensors instant, press the [HOME] key for 2 seconds. ❇Two “gongs” and two “beeps” will sound and the

START IN OFF OR CHIME MODE

START IN HOME MODE

HOLD DOWN HOME

HOLD DOWN

HOME light will blink continuously. ◆Because all exit/entry sensors will now cause an

1 GONG & 2 BEEPS

2 GONGS & 2 BEEPS

instant alarm when in Home Mode, the Console must be disarmed before opening any exit/entry delay door.

DONE

DONE

Page 21 of the Linear Digital Video Recorder (DVS-2400) user manual — 1 GONG & 3 BEEPS
Page 21 · click to enlarge
Page 21

AWAY MODE

MANUAL BYPASSING OF SENSORS

◆Use this mode when no one will be staying home. ◆Each burglary sensor can trigger the siren once

◆ Manual bypassing of sensors in the Away Mode

allows arming of the system with open doors and windows, while still having perimeter protection with other closed doors and windows. ◆The Console will resist arming with open door or

per arming period. ◆ Away Mode causes an instant alarm when any

perimeter sensor is triggered. ◆Away Mode causes a delayed alarm when any

window sensors. ❇ Four high-low beeps to warn the user that

exit/entry sensor is triggered. ◆Away Mode causes an instant alarm when any

something is open and the system will remain in the previous mode. ❇Lit sensor status indicators show which sensors

interior sensors (motion detectors, etc.) are triggered. The interior sensors will be delayed if a perimeter delayed sensor is triggered first. ◆Alarm siren stops automatically after five

are open. To manually bypass the open sensors, arm the system again within 5 seconds. ❇A “gong” and three “beeps” will sound, the

minutes and the system will remain armed. Arm to Away Mode by entering a user code, and pressing [AWAY]. The user can “Quick Arm” to Away Mode from Home, Chime or Off Mode by holding down the [AWAY] key for two seconds. (Quick arming can be disabled; see the “Advanced Programming” section of this manual.)

AWAY indicator will light, and the open sensors will be bypassed. ✍WARNING: Bypassed sensors cannot cause an

alarm.

EXIT DELAY (For Leaving the Premises) ❇When the system is armed to the Away Mode, the

Console will sound a “Gong” and three “Beeps”. ❇During the 60 second Exit Delay, the Console

will sound “beeps” (double beeps last 10 seconds) and the AWAY light will blink. ◆The Exit Delay gives the user 60 seconds to

AWAY MODE

START HERE

leave the premises through an exit/entry door without triggering an alarm. ◆Re-entering during the Exit Delay will extend the

(OPTIONAL)

Exit Delay another 60 seconds (one time only). ❇When the Exit Delay is over, the Console will

sound one “gong” to warn the user that the system is fully armed. ✍NOTE: The Exit Delay time can be changed; see the

YOUR USER CODE

“Advanced Programming” section of this manual.

ENTRY DELAY (For Entering the Premises) ◆The Entry Delay gives the user 30 seconds to

1 GONG & 3 BEEPS

enter the premises through an exit/entry door without triggering an alarm. ◆If a exit/entry sensor is triggered, starting the

DONE

Entry Delay, the interior sensors will also become delayed (this allows motion in the premises during the Entry Delay). ❇During the 30 second Entry Delay, the Console will

sound “beeps”. ◆ When the Entry Delay is over, the Console will

QUICK ARM

go into full alarm and sound the siren if it is not disarmed to the Off or Chime Mode. ❇If an alarm has occurred while the user was

START HERE

HOLD DOWN

gone, multiple beeps will sound after disarming and the sensor light for the sensor(s) that caused the alarm will flash (switch to Off Mode again or re-arm the Console to stop the flashing alarm memory light). ✍NOTE: The Entry Delay time can be changed; see the

1 GONG & 3 BEEPS

DONE

“Advanced Programming” section of this manual.

Page 22 of the Linear Digital Video Recorder (DVS-2400) user manual — TEST MODE
Page 22 · click to enlarge
Page 22

TEST MODE

◆ Even though this is a self-monitoring supervised

system, the National Burglar and Fire Alarm Association recommends that all security systems should be tested manually on a regular basis. ◆The Console must be in Off Mode before going

TEST MODE

to Test Mode. Switch the Console into Test Mode by entering a user code and pressing [TEST]. ❇When the system is switched to the Test Mode,

Linear Digital Video Recorder (DVS-2400) — TEST MODE diagram (page 22)
Fig. 37

the Console will sound a “Gong” and four “Beeps”. Holding down the [TEST] button in Test Mode will light all of the Console’s indicators. ❇The sensor status lights will flash for each sensor

programmed into the Console. Go to each sensor and press its test button or open and close the protected opening. To test the wireless keypad, press the [(A)] key. ❇The Console will make a “bing” sound as each

sensor is tested, followed by 1-3 beeps indicating signal strength with 3 beeps being the strongest signal. ❇As each sensor is tested, the sensor status light

for the sensor will stop flashing and return to showing the current status of the sensor. Continue testing until there are no flashing status lights. ✍NOTE: If the Console is left unattended in Test

Mode, it will automatically switch back to Off Mode after 3 minutes. ◆When directly connecting (without a telephone

line) to the DVS-2400 with the RA-2400 remote access software (Version 1.3 or later), press the [EMERGENCY] key while in Test Mode to cause the Console to connect to the modem.

Linear Digital Video Recorder (DVS-2400) — TEST MODE diagram (page 22)
Fig. 38

SENSOR FUNCTION OFF MODE CHIME MODE HOME MODE AWAY MODE

LEFT BUTTON SWITCHES CONSOLE TO AWAY MODE † IF ALARM HAS OCCURED, SWITCHES CONSOLE TO OFF MODE ‡ LEFT BUTTON SWITCHES TO OFF MODE ‡

LEFT BUTTON SWITCHES CONSOLE TO AWAY MODE † IF ALARM HAS OCCURED, SWITCHES CONSOLE TO OFF MODE ‡ RIGHT BUTTON SWITCHES TO OFF MODE ‡

† CAN BE HOME MODE USING PROGRAMMING STEP 50 ‡ CAN BE CHIME MODE USING PROGRAMMING STEP 51 Sensor Function Table

Page 23 of the Linear Digital Video Recorder (DVS-2400) user manual — SENSOR RADIO TROUBLE
Page 23 · click to enlarge
Page 23

10. SYSTEM TROUBLE INDICATIONS

◆ The DVS-2400 Console is a self-monitoring

supervised wireless system. ◆If the Console detects a problem with any of the

supervised system sensors or backup battery, it will display the appropriate trouble indication and, if monitored, report the trouble to the Central Station through the communicator (depending on communicator programming).

CONSOLE LOW BATTERY

◆ The Console constantly charges and monitors

POWER INDICATOR

Linear Digital Video Recorder (DVS-2400) — CONSOLE LOW BATTERY diagram (page 23)
Fig. 39

the optional backup battery (if installed). ◆If the backup battery condition is abnormal, the

ON WITH AC POWER AND CHARGED BACKUP BATTERY

BLINKS WITH LOW, RECHARGING OR MISSING BACKUP BATTERY

Console’s POWER light will indicate the trouble. ❇The POWER indicator normally glows when AC

DIM WHEN AC POWER IS ABSENT AND CONSOLE IS RUNNING ON BACKUP BATTERY

power is on. ❇ With a charged backup battery installed, if the

Console looses AC power, the POWER indicator will dim as the Console runs on the backup battery. ❇If the backup battery is low, recharging, or not

installed, the POWER indicator blinks when AC power is present. ❇If the AC power is off and no backup battery is

installed, the POWER indicator will be off (in this case the system has no power and is disabled). Normal battery life for the type of backup battery used in the Console is 3-4 years. If the battery does not take a charge in 72 hours, it should be replaced.

SENSOR LOW BATTERIES

❇ When the BATTERIES indicator on the Console

BATTERIES INDICATOR

BLINKS WHEN ONE OR MORE SENSORS HAVE A LOW BATTERY

blinks, one or more sensors have a low battery. Press [∗] key for one second to view sensor status. Sensor status indicator for any sensor with a low battery will light along with the BATTERIES indicator. Replace the sensor’s battery as described in their instructions. Switch to Test Mode after replacing the sensor battery and completely test the system (see Test Mode). Switching to Test Mode clears the low battery indication.

LIGHTS WITH SENSOR INDICATOR DURING LOW BATTERY STATUS CHECK (PRESS FOR 1 SECOND)

SENSOR RADIO TROUBLE

❇ When the TROUBLE indicator blinks, one or

TROUBLE INDICATOR

more sensors have not reported status during the eight hour status time window. Press [∗] key for one second to view sensor status. Sensor status indicator for any sensor that has not reported in will light along with the TROUBLE indicator. Switch to Test Mode after servicing the sensor and completely test the system (see Test Mode). Switching to Test Mode clears the trouble indication.

BLINKS WHEN ONE OR MORE SENSORS HAVE NOT REPORTED STATUS DURING THE EIGHT HOUR STATUS TIME WINDOW

LIGHTS WITH SENSOR INDICATOR DURING TRANSMITTER STATUS CHECK (PRESS FOR 1 SECOND)

Page 24 of the Linear Digital Video Recorder (DVS-2400) user manual — TEST 1 BING
Page 24 · click to enlarge
Page 24

11. CUSTOMIZING THE SYSTEM

◆ Adding additional sensors will increase the

protection provided by the system. ◆ All ground-level perimeter openings and

accessible upper-story openings need protection. ◆Motion detectors can protect interior areas and

areas where valuables are kept.

ADDING SENSORS TO THE SYSTEM

START IN TEST

Always start with the Console in Test Mode (enter a user code and press [TEST]). Enter the master user code then press the [TEST] button. ❇A “gong” and five “beeps” will sound. ❇The sensor status indicators will light for each

MASTER USER CODE

sensor programmed into the Console. Enter an unused sensor number from 01-24 (you must enter two digits, example: 5 = 05). ✍NOTE: A sensor can be learned into more than

1 GONG & 5 BEEPS

TEST

one location. Be sure to choose an unused sensor number. If a sensor gets entered into more than one location, delete the duplicates using the remove sensor function. ❇The sensor indicator light will flash for the sensor

NEW SENSOR NUMBER

number selected. Activate the sensor. (To add a wireless keypad, press the keypad’s [∗] key.) ❇A single “bing” tone will sound when the sensor

ACTIVATE SENSOR

is learned by the Console and the sensor status indicator will stay lit. Enter another sensor number or exit Setup Mode by holding the [OFF] button for three seconds.

DONE

REMOVING SENSORS FROM THE SYSTEM

◆ If a previously learned sensor isn’t going to be

used with the system anymore, or it’s a duplicate that has been entered into more than one sensor location, it should be removed from the Console’s memory. ◆Start with the Console in Test Mode.

START IN TEST

MASTER USER CODE

Enter the master user code then press the [TEST] button. ❇A “gong” and five “beeps” will sound. ❇The sensor status indicators will light for each

sensor programmed into the Console. Enter the sensor number (from 01-24) that you want to remove (you must enter two digits, example: 5 = 05). ❇The sensor indicator light will flash for the sensor

1 GONG & 5 BEEPS

TEST

SENSOR NUMBER TO REMOVE

number selected. Press the [TEST] button. ❇A single “bing” tone will sound when the sensor

has been removed and the sensor status indicator will turn off. Enter another sensor number or exit Setup Mode by holding the [OFF] button for three seconds.

TEST 1 BING

DONE

Page 25 of the Linear Digital Video Recorder (DVS-2400) user manual — SENSOR NUMBER FOR INTERIOR
Page 25 · click to enlarge
Page 25

MAKING A SENSOR A 24-HOUR DOOR CHIME

START IN TEST

◆ Sensors can be programmed to cause the

Console to chime any time they’re activated. ◆Chime-only sensors will not be able to trigger the

MASTER USER CODE

alarm in any Console mode. ◆The sensor must have already been learned by

the Console (see “Adding sensors to the System” for details). Start with the Console in Test Mode. Enter the master user code then press the [TEST] button. ❇A “gong” and five “beeps” will sound. ❇The sensor status indicators will light for each

1 GONG & 5 BEEPS

TEST

SENSOR NUMBER FOR CHIME

sensor programmed into the Console. Enter the sensor number from 01-24 (you must enter two digits, example: 5 = 05). ❇The sensor indicator light will flash for the sensor

number selected. Press [HOME], 8, then [AWAY]. A “bing” tone will sound. Enter another sensor number or exit Setup Mode by holding the [OFF] button for three seconds.

8 TUV 8 FOR CHIME FUNCTION

MAKING A SENSOR INTERIOR

1 BING

◆ Motion detectors are automatically programmed

as interior sensors. Any other sensor can also be programmed as an interior sensor. ◆Interior sensors can only trigger an alarm when

DONE

the Console is in Away Mode. ◆“Home Interior” sensors can trigger an alarm

when the Console is in the Home or Away mode. ◆The sensor must have already been learned by

START IN TEST

the Console (see “Adding sensors to the System” for details). Start with the Console in Test Mode. Enter the master user code then press the [TEST] button. ❇A “gong” and five “beeps” will sound. ❇The sensor status indicators will light for each

MASTER USER CODE

sensor programmed into the Console. Enter the sensor number from 01-24 (you must enter two digits, example: 5 = 05). ❇The sensor indicator light will flash for the sensor

1 GONG & 5 BEEPS

TEST

number selected. Press [HOME], 7, then [AWAY]. A “bing” tone will sound. Enter another sensor number or exit Setup Mode by holding the [OFF] button for three seconds.

SENSOR NUMBER FOR INTERIOR

7 FOR INTERIOR FUNCTION

7 PRS

1 BING

DONE

Page 26 of the Linear Digital Video Recorder (DVS-2400) user manual — different sensor functions. ◆ The sensor must have already been learned by
Page 26 · click to enlarge
Page 26

MAKING A SENSOR PERFORM A DIFFERENT FUNCTION

◆ Sensors can be reprogrammed to perform

Linear Digital Video Recorder (DVS-2400) — MAKING A SENSOR PERFORM A DIFFERENT FUNCTION diagram (page 26)
Fig. 40

different sensor functions. ◆ The sensor must have already been learned by

the Console (see “Adding Sensors to the System” for details). Start with the Console in Test Mode. Enter the master user code then press the [TEST] button. ❇A “gong” and five “beeps” will sound. ❇The sensor status indicators will light for each

sensor programmed into the Console. Enter the sensor number from 01-24 (you must enter two digits, example: 5 = 05). ❇The sensor indicator light will flash for the sensor

number selected. Choose a function number from the Sensor Function Table. Press [HOME], the new function number, then [AWAY]. A “bing” tone will sound. Enter another sensor number or exit Setup Mode by holding the [OFF] button for three seconds.

Linear Digital Video Recorder (DVS-2400) — different sensor functions. ◆ The sensor must have already been learned by diagram (page 26)
Fig. 41 · different sensor functions. ◆ The sensor must have a…

# SENSOR FUNCTION OFF MODE CHIME MODE HOME MODE AWAY MODE

3 PANIC ARMED 24-HOURS - TRIGGERS SILENT PANIC ALARM

9 2-BUTTON ARM/DISARM (LEFT) 2-BUTTON AUTOMATION (RIGHT) EMERGENCY (BOTH)

LEFT BUTTON SWITCHES CONSOLE TO AWAY MODE † IF ALARM HAS OCCURED, SWITCHES CONSOLE TO OFF MODE ‡ LEFT BUTTON SWITCHES TO OFF MODE ‡

10 2-BUTTON ARM (LEFT) 2-BUTTON DISARM (RIGHT) EMERGENCY (BOTH)

LEFT BUTTON SWITCHES CONSOLE TO AWAY MODE † IF ALARM HAS OCCURED, SWITCHES CONSOLE TO OFF MODE ‡ RIGHT BUTTON SWITCHES TO OFF MODE ‡

† CAN BE HOME MODE USING PROGRAMMING STEP 50 ‡ CAN BE CHIME MODE USING PROGRAMMING STEP 51 Sensor Function Table

Page 27 of the Linear Digital Video Recorder (DVS-2400) user manual — 87 REMOTE ACCESS PASSWORD 6 DIGITS 987654
Page 27 · click to enlarge
Page 27

12. ADVANCED PROGRAMMING

◆ To perform any of the advanced programming

SETUP MODE

steps, the Console must be in the Setup Mode. ◆Each programming function is performed with

Start with the Console in Test Mode (Setup Mode cannot be reached from any other mode). From Test Mode, enter the master user code then press [TEST]. ✍NOTE: Only the master user code can be used to

similar keystrokes. After the Console is in Setup Mode, enter the programming step number, press the [HOME] key (HOME = program), enter the new value, and press the [AWAY] key (AWAY = store). Follow the figures next to the programming steps.

put the Console into the Setup Mode. The restricted user codes cannot access Setup Mode. ❇A “gong” and five “beeps” will sound, signaling

that the Console is in Setup Mode. Hold the [OFF] key for three seconds when you want to exit Setup Mode. ✍NOTE: If the Console is left unattended in Setup

HOME TEST = PROGRAM = REMOVE

AWAY = STORE

Mode, it will automatically switch back to Off Mode after three minutes.

CONSOLE PROGRAMMING OPTIONS

STEP # PROGRAMMING FUNCTION POSSIBLE VALUES FACTORY VALUE INSTALLATION VALUE

25 ENTRY DELAY 20-255 SECONDS 30

26 EXIT DELAY 20-255 SECONDS 60

30 BURGLARY SIREN TIME 1-30 MINUTES 5

31 EMERGENCY SIREN TIME 1-30 MINUTES 5

32 FIRE SIREN TIME 1-30 MINUTES 5

40 AUTOMATION OUTPUT TIME 0-2500 SECONDS (0 = TOGGLE ON/OFF) 0

50 REMOTE ARMING MODE 2 = HOME MODE; 3 = AWAY MODE 3

51 REMOTE DISARMING MODE 0 = OFF MODE; 1 = CHIME MODE 0

61 ENTRY DELAY BEEPS 0 = OFF; 1 = ON 1

62 EXIT DELAY BEEPS 0 = OFF; 1 = ON 1

63 SILENT BURGLARY ALARM 0 = AUDIBLE; 1 = SILENT 0

64 SILENT EMERGENCY ALARM 0 = AUDIBLE; 1 = SILENT 0

65 QUICK ARMING 0 = OFF; 1 = ON 1

66 AUTO RESTORE 0 = OFF; 1 = ON 1

67 AUTO BYPASS 0 = OFF; 1 = ON 0

68 AUTOMATION MODE DURING ALARM 0 = FLASH (ENABLED BY FUNCTION 72) 1 = STEADY (ENABLED BY FUNCTION 72) 0

69 AUTOMATION BING TONE 0 = NO BINGS 1 = BINGS 1

70 REMOTE ARM/DISARM CHIRP 0 = NO CHIRPS 1 = CHIRPS (1 CHIRP = ARMED, 2 CHIRPS = DISARMED) 1

71 AUTOMATION FLASHES AFTER ALARM 0 = STANDARD 1 = FLASHING AFTER ALARM 0

0 = STANDARD 1 = AUTOMATION ACTIVE DURING ALARM (FLASH OR STEADY PROGRAMMED BY FUNCTION 68)

72 AUTOMATION ACTIVE DURING ALARM

73 AUTOMATION ON WHILE ARMED 0 = STANDARD 1 = ON WHILE ARMED 0

74 AUTOMATION ON DURING EXIT/ENTRY 0 = STANDARD 1 = ON DURING EXIT/ENTRY DELAYS 0

75 AUTOMATION POLARITY 0 = + WHEN OFF; 1 = + WHEN ON 1

87 REMOTE ACCESS PASSWORD 6 DIGITS 987654

92 DURESS CODE 1-5 DIGITS REMOVED

93 RESTRICTED USER CODE #1 1-5 DIGITS REMOVED

94 RESTRICTED USER CODE #2 1-5 DIGITS REMOVED

95 RESTRICTED USER CODE #3 1-5 DIGITS REMOVED

96 RESTRICTED USER CODE #4 1-5 DIGITS REMOVED

97 RESTRICTED USER CODE #5 1-5 DIGITS REMOVED

98 PAGE ALERT USER CODE 1-5 DIGITS REMOVED

99 MASTER USER CODE 1-5 DIGITS 1234

Console Programming Table

Page 28 of the Linear Digital Video Recorder (DVS-2400) user manual — TIME IN MINUTES (1-30)
Page 28 · click to enlarge
Page 28

CHANGING A SENSORS SUPERVISION

◆ When a sensor is programmed, the Console sets

SENSOR NUMBER TO CHANGE

all stationary sensors as supervised, and all portable sensors as non-supervised. ◆The Console expects hourly status transmissions

from any sensor programmed as supervised. ◆Any sensor can be programmed as supervised

16 FOR NON-SUPERVISED 17 FOR SUPERVISED

or non-supervised. ✍ NOTE: Don’t program a sensor that doesn’t send

status transmissions as supervised.

CHANGING A SENSORS RESTORE REQUIREMENTS

◆ When a sensor is programmed, the Console

SENSOR NUMBER TO CHANGE

automatically recognizes it as manually or automatically restoring. ◆The Console expects restoral signals from any

sensor programmed as manual restore. ◆Any sensor can be programmed as manual or

18 FOR MANUAL RESTORE 19 FOR AUTO RESTORE

automatic restore. ✍ NOTE: Don’t program a sensor that doesn’t send

restoral transmissions as manual restore.

ENTRY DELAY TIME

◆The factory-set Entry Delay time is 30 seconds. ◆The Entry Delay time can be adjusted from 20 to

PROGRAMMING STEP #25

JKL

255 seconds. ✍ NOTE: Don’t make the Entry Delay too short. The

user may not have enough time to disarm the system before an alarm. Write the new Entry Delay time in the User’s Guide.

TIME IN SECONDS (20-255)

EXIT DELAY TIME

◆The factory-set Exit Delay time is 60 seconds. ◆The Exit Delay time can be adjusted from 20 to

PROGRAMMING STEP #26

255 seconds. Write the new Exit Delay time in the User’s Guide.

TIME IN SECONDS (20-255)

BURGLARY SIREN TIME

◆ The factory-set burglary siren time is five

3 DEF

PROGRAMMING STEP #30

minutes. ◆ The burglary siren time can be adjusted from

one to 30 minutes.

TIME IN MINUTES (1-30)

EMERGENCY SIREN TIME

◆ The factory-set emergency siren time is five

3 DEF

PROGRAMMING STEP #31

minutes. ◆ The emergency siren time can be adjusted from

one to 30 minutes.

TIME IN MINUTES (1-30)

Page 29 of the Linear Digital Video Recorder (DVS-2400) user manual — PROGRAMMING STEP #62
Page 29 · click to enlarge
Page 29

FIRE SIREN TIME

◆The factory-set fire siren time is five minutes. ◆The fire siren time can be adjusted from one to

3 DEF

PROGRAMMING STEP #32

2 ABC

30 minutes.

TIME IN MINUTES (1-30)

AUTOMATION OUTPUT TIME

◆ The factory setting causes the Automation Output

4 GHI

PROGRAMMING STEP #40

to toggle between on and off with each activation. ◆The Automation Output can be programmed to

turn on, then automatically turn off after one to 2500 seconds (42 minutes).

TIME IN SECONDS (1-2500) 0 = TOGGLE ON & OFF

REMOTE CONTROL ARMING LEVEL

◆ The factory setting causes the portable remote

5 JKL

controls to arm to the Away Mode. ◆Alternately, the portable remote controls can

PROGRAMMING STEP #50

arm to the Home Mode. ◆Changing this setting will affect all the portable

2 FOR HOME MODE 3 FOR AWAY MODE

remote controls used with the system.

REMOTE CONTROL DISARMING LEVEL

◆ The factory setting causes the portable remote

5 JKL

controls to disarm to the Off Mode. ◆Alternately, the remote controls can disarm to

PROGRAMMING STEP #51

the Chime Mode. ◆ Changing this setting will affect all the portable

0 FOR OFF MODE 1 FOR CHIME MODE

remote controls used with the system.

ENTRY DELAY BEEPS

◆ The factory setting causes the Console to beep

6 MNO

during Entry Delays. ◆Alternately, the Entry Delay beeps can be silenced. ◆With the Entry Delay beeps off, the Console will

PROGRAMMING STEP #61

be silent after a delayed sensor is triggered until the Entry Delay expires, then the alarm siren will sound.

0 FOR ENTRY BEEPS OFF 1 FOR ENTRY BEEPS ON

EXIT DELAY BEEPS

◆ The factory setting causes the Console to beep

6 MNO

during Exit Delays. ◆Alternately, the Exit Delay beeps can be silenced. ◆With the Exit Delay beeps off, the Console will be

PROGRAMMING STEP #62

2 ABC

silent after arming to the Away Mode until the Exit Delay expires, then a single “gong” tone will sound.

0 FOR EXIT BEEPS OFF 1 FOR EXIT BEEPS ON

Page 30 of the Linear Digital Video Recorder (DVS-2400) user manual — 6 MNO
Page 30 · click to enlarge
Page 30

SILENT BURGLARY ALARMS

◆ The factory setting causes audible burglary

6 MNO

alarms. ◆ Alternately, the Console can be programmed for

PROGRAMMING STEP #63

3 DEF

silent burglary alarms.

0 FOR AUDIBLE BURGLAR 1 FOR SILENT BURGLAR

SILENT EMERGENCY ALARMS

◆ The factory setting causes audible emergency

6 MNO

alarms. ◆ Alternately, the Console can be programmed for

PROGRAMMING STEP #64

4 GHI

silent emergency alarms.

0 FOR AUDIBLE EMERGENCY 1 FOR SILENT EMERGENCY

DISABLING QUICK ARMING

◆ The factory setting allows the Console to be

6 MNO

armed by holding down the mode keys for two seconds. ◆Alternately, the Console can be programmed to

PROGRAMMING STEP #65

5 JKL

not allow quick arming. ◆If quick arming is disabled, a user code must be

0 FOR QUICK ARMING OFF 1 FOR QUICK ARMING ON

entered before pressing the mode buttons. ✍NOTE: For commercial installations, it is

recommended to disable quick arming to prevent customers from arming the system. ✍NOTE: If quick arming is disabled the Home

Instant Mode is unavailable.

AUTOMATIC RESTORAL OF BYPASSED SENSORS

◆ Bypassed sensors are ignored by the Console

6 MNO

and cannot cause an alarm. ◆The factory setting causes the Console to

PROGRAMMING STEP #66

6 MNO

automatically restore any bypassed sensor when the sensor closes. After it’s restored, the sensor is ready to cause an alarm the next time it is opened. ◆Alternately, the Console can be programmed to

0 FOR AUTO RESTORAL OFF 1 FOR AUTO RESTORAL ON

not automatically restore (remove the bypass from) sensors that close. Bypassed sensors will remain bypassed until the system is disarmed.

AUTOMATIC BYPASSING OF OPEN SENSORS

◆ The factory setting requires the user to manually

bypass any open sensors when the system is armed. ◆If arming is attempted with open sensors, the

6 MNO

PROGRAMMING STEP #67

7 PRS

Console will sound five two-tone beeps and will not arm. ◆Arming to the same mode again within five

0 FOR AUTO BYPASS OFF 1 FOR AUTO BYPASS ON

seconds will bypass any open sensors and arm the Console. ◆Alternately, the Console can be programmed to

automatically bypass any open sensors when the system is armed.

Page 31 of the Linear Digital Video Recorder (DVS-2400) user manual — PROGRAMMING STEP #72
Page 31 · click to enlarge
Page 31

AUTOMATION OUTPUT MODE DURING ALARM

✍ NOTE: For the Automation Output to activate

6 MNO

during an alarm, that function must be enabled with Programming Step 71 or 72. ◆If the Automation output is programmed to

PROGRAMMING STEP #68

8 TUV

activate during an alarm, it can be programmed to flash or be steady.

0 FOR FLASHING OUTPUT ON ALARM 1 FOR STEADY OUTPUT ON ALARM

AUTOMATION ACTIVATION TONE

◆ The factory setting causes the Console to sound

a “bing” when the Automation Output is activated by pressing the [(A)] key, or when it’s triggered with a two-button remote control. ◆Alternately, this sound can be silenced.

6 MNO

PROGRAMMING STEP #69

9 WXY

0 FOR BING TONE OFF 1 FOR BING TONE ON

REMOTE CONTROL ARM/DISARM CHIRP

◆ When arming with the portable remote control,

7 PRS

the factory setting causes the Console to “chirp” once when armed, twice when disarmed, and three times when arming with sensors bypassed. ◆Alternately, these chirps can be silenced. ✍NOTE: If these chirps are silenced, it is

PROGRAMMING STEP #70

0 FOR CHIRPS OFF 1 FOR CHIRPS ON

recommended to program the Automation Output to be active when the system is armed, so a light can be triggered displaying the arming status of the Console.

AUTOMATION OUTPUT FLASHES DURING AND AFTER ALARM

◆ The factory setting causes the Console’s

7 PRS

Automation Output to activate when pressing the [(A)] key, or when it’s triggered with a two-button remote control. ◆In addition, the Console can be programmed to

PROGRAMMING STEP #71

0 FOR STANDARD TRIGGER 1 FOR FLASHING DURING & AFTER ALARM

flash the Automation Output during and after any alarms. ◆The output will continue to flash until the flashing

status lights are cleared.

AUTOMATION OUTPUT ON DURING ALARM

◆ The factory setting causes the Console’s

7 PRS

Automation Output to activate when pressing the [(A)] key, or when it’s triggered with a two-button remote control. ◆In addition, the Console can be programmed to

PROGRAMMING STEP #72

2 ABC

0 FOR STANDARD TRIGGER 1 FOR OUTPUT DURING ALARM

activate the Automation Output during alarms. ✍NOTE: The Automation Output can be

programmed to flash or be steady during alarm, see Programming Step 68.

Page 32 of the Linear Digital Video Recorder (DVS-2400) user manual — MASTER USER CODE
Page 32 · click to enlarge
Page 32

AUTOMATION OUTPUT WHILE ARMED

◆ The factory setting causes the Console’s

7 PRS

PROGRAMMING STEP #73

Automation Output to activate when pressing the [(A)] key, or when it’s triggered with a two-button remote control. ◆In addition, the Console can be programmed to

3 DEF

0 FOR STANDARD TRIGGER 1 FOR OUTPUT WHEN ARMED

activate the Automation Output when the system is armed.

AUTOMATION OUTPUT DURING EXIT/ENTRY DELAYS

◆ The factory setting causes the Console’s

7 PRS

PROGRAMMING STEP #74

Automation Output to activate when pressing the [(A)] key, or when it’s triggered with a two-button remote control. ◆In addition, the Console can be programmed to

4 GHI

0 FOR STANDARD TRIGGER 1 FOR OUTPUT DURING EXIT/ENTRY DELAYS

activate the Automation Output during the exit and Entry Delays.

AUTOMATION OUTPUT POLARITY

◆ The factory setting causes the Console’s

7 PRS

PROGRAMMING STEP #75

Automation Output to provide a current limited voltage source when activated. ◆Alternately, the Console can be programmed so

5 JKL

0 FOR VOLTAGE WHEN OFF 1 FOR VOLTAGE WHEN ON

the Automation Output provides a current limited voltage source when deactivated.

REMOTE ACCESS PASSWORD

◆ This is the password used to gain access to the

8 TUV

PROGRAMMING STEP #87

7 PRS

Console when using the RA-2400 remote access software. ◆The password must be 6-digits long.

6-DIGIT REMOTE ACCESS PASSWORD

Log the remote access password in the box below.

REMOTE ACCESS PASSWORD

DURESS CODE

◆ The duress code will disarm the system, without

9 WXY

PROGRAMMING STEP #92

2 ABC

any special indications or sounds, but will send the programmed duress code to the Central Station. ◆The duress code should be two or more digits

1-5 DIGIT DURESS CODE (3-5 DIGITS RECOMMENDED)

different than any user code. Log the duress code in the box below.

DURESS CODE

MASTER USER CODE

◆ The master user code is 1234 when power is first

9 WXY

9 WXY

PROGRAMMING STEP #99

applied to the Console. ◆The master user code can be changed through

programming to any 1-5 digit code. Only the master user can access Setup Mode, restricted users cannot. ✍NOTE: For maximum security, a 3-5 digit code is

1-5 DIGIT MASTER CODE (3-5 DIGITS RECOMMENDED)

recommended. Log the master user code in the box below.

MASTER USER CODE

Page 33 of the Linear Digital Video Recorder (DVS-2400) user manual — TEST
Page 33 · click to enlarge
Page 33

ADDITIONAL USER CODES

◆ The Console can be programmed with five

PROGRAMMING STEPS #93 TO 98

restricted user codes and one page alert user code. ◆The restricted user codes operate the system as

usual, but cannot access Setup Mode. ◆The restricted user codes can access a special

1-5 DIGIT CODE (3-5 DIGITS RECOMMENDED)

Code Mode that can be used to change or remove any of the five restricted user codes, the page alert user code, or the duress code. ◆The page alert user code dials the supervisory

number (programmed for a pager) when it is used to ARM OR DISARM the system. ◆A restricted user code is a good one to give to

STEP # 93 RESTRICTED USER CODE #1

STEP # 94 RESTRICTED USER CODE #2

STEP # 95 RESTRICTED USER CODE #3

children or any user that should be restricted from programming the Console. ✍NOTE: For maximum security, a 3-5 digit code is

STEP # 96 RESTRICTED USER CODE #4

STEP # 97 RESTRICTED USER CODE #5

recommended. ✍ WARNING: NEVER PROGRAM ANY RESTRICTED

STEP # 98 PAGE ALERT USER CODE

OR PAGE ALERT USER CODE THE SAME AS THE MASTER USER CODE! Log the restricted user codes in the boxes.

Linear Digital Video Recorder (DVS-2400) — STEP # 96 RESTRICTED USER CODE #4 diagram (page 33)
Fig. 42

◆ Any restricted, duress or page alert user code

can be removed from the Console. ◆Because access to programming would be

impossible without a master user code, it cannot be removed using these steps. ◆The master user code can be changed using

programming Step #99. ✍ NOTE: The master user code can be removed

using the Console master reset, although all other system programming with be reset to factory values and all sensors programmed will be erased.

CONSOLE MASTER RESET

◆ Master resetting the Console will set all of the

START IN TEST

programming options back to the factory values. The master user code will be reset to 1234. ✍CAUTION: Master resetting the Console will erase

MASTER USER CODE

the user codes and remove all programmed sensors. All Console and communicator programming values will be reset to the factory defaults. Start with the system in Test Mode (Setup Mode cannot be reached from any other mode). From the Test Mode, enter the master user code then press [TEST]. ❇A “Gong” and five “Beeps” will sound, signaling

1 GONG & 5 BEEPS

TEST

9 WXY

STEP #999 FOR MASTER RESET

9 WXY

USE THESE EXACT KEYSTROKES TO PERFORM A MASTER RESET

that the system is in Setup Mode. Enter programming Step #999. Press [TEST]. Enter the numbers 999 again. Press [TEST] again. ❇A “Bing” will sound to indicate the beginning of

9 WXY

PRESS TEST

TEST

9 WXY

ENTER 999 TO OK THE MASTER RESET

the reset process. This process will take up to 10 seconds while the memory is being reset. ◆The system will revert to the first time power-up

9 WXY

9 WXY

condition and the new master user code will be 1234. Go to the “Basic Console Programming” section of this manual to begin re-programming the system.

PRESS TEST, 1 BING SOUNDS, WAIT ABOUT 10 SECONDS

TEST

DONE

Page 34 of the Linear Digital Video Recorder (DVS-2400) user manual — GENERAL COMMUNICATOR OPTIONS
Page 34 · click to enlarge
Page 34

13. COMMUNICATOR PROGRAMMING

SETUP MODE

◆ To perform any of the communicator

programming steps, the Console must be in the Setup Mode. ◆Each programming function is performed with

similar keystrokes. After the Console is in Setup Mode, enter the programming step number, press the [HOME] key (HOME = program), enter the new value, and press the [AWAY] key (AWAY = store). Follow the figures next to the programming step. Start with the Console in Test Mode (Setup Mode cannot be reached from any other mode). From Test Mode, enter the master user code then press [TEST]. ✍NOTE: Only the master user code can be used to

SETUP MODE

START IN TEST

MASTER USER CODE

put the Console into the Setup Mode. The restricted user codes cannot access Setup Mode. ❇A “gong” and five “beeps” will sound, signaling

1 GONG & 5 BEEPS TEST

that the Console is in Setup Mode. Hold the [OFF] key for three seconds when you want to exit Setup Mode. ✍NOTE: If the Console is left unattended in Setup

Mode, it will automatically switch back to Off Mode after three minutes.

GENERAL COMMUNICATOR OPTIONS

STEP # PROGRAMMING

POSSIBLE

FACTORY

INSTALLATION

FUNCTION

VALUES

VALUE

VALUE

76 2-WAY AUDIO 0 = NONE; 1 = LISTEN; 2 = 2-WAY MANUAL; 3 = 2-WAY FULL DUPLEX 0

78 VOICE RESPONSE FROM CONSOLE SPEAKER (AND REMOTE SPEAKER IF USED)

0 = VOICE RESPONSE DISABLED 1 = VOICE RESPONSE ENABLED 0

100 REMOTE PROGRAMMING LOCKOUT 0 = UNLOCK; 1 = LOCK 0

101 CALL LIMITER 0 = OFF; 1 = FIVE CALLS PER ARMING PERIOD 0

103 DIALING DELAY 0 = NO DELAY; 1 = 30 SECOND DELAY 0

104 DIALING METHOD 0 = TONE; 1 = PULSE 0

107 COMMUNICATOR ENABLE 0 = COMMUNICATOR OFF, 1 = COMMUNICATOR ON 0

General Communicator Programming Table

Page 35 of the Linear Digital Video Recorder (DVS-2400) user manual — 0 FOR UNLOCK 1 FOR LOCK
Page 35 · click to enlarge
Page 35

GENERAL COMMUNICATOR OPTIONS

COMMUNICATOR ENABLE

◆ The factory setting for the Console disables the

PROGRAMMING STEP #107

communicator. If the system is going to be a non-monitored, local alarm only, leave the communicator disabled. ◆If the system is going to be monitored by a

7 PRS

0 FOR COMMUNICATOR OFF 1 FOR COMMUNICATOR ON

Central Station, enable the communicator with this programming step.

2-WAY AUDIO ◆ When the Model VB-2 voice module is installed,

7 PRS

PROGRAMMING STEP #76

the communicator can provide 2-way audio capability. ◆The audio module can be programmed for listen

6 MNO

0 FOR NO AUDIO MONITORING 1 FOR LISTEN-ONLY 2 FOR 2-WAY MANUAL 3 FOR 2-WAY FULL DUPLEX

only, 2-way manual operation (using a pushbutton telephone at the Central Station), and 2-way full duplex hands free operation. ◆Refer to the VB-2 installation instructions for

details on operating the audio module. ✍NOTE: The Model VB-2 Digital Voice Synthesis

module must be installed for this option to function. ◆The factory setting for the VB-2 audio module is

OFF. ◆ Alternately, the audio module can be set for (1)

listen-only, (2) 2-way manual, (3) 2-way full duplex. ✍NOTE: Units programmed for two-way duplex can

still be controlled manually by pressing the “1" or ”3" key. In addition, the Central Station can return the unit to two-way duplex by pressing the “8" key.

VOICE RESPONSE

◆ The Console can be programmed to allow its

7 PRS

PROGRAMMING STEP #78

speaker to play audio produced by the VB-2 or VB-3 digital voice synthesis modules. ◆This selection can also be used when a remote

8 TUV

speaker is connected to the Console. ◆The factory setting is to disable the Console’s

0 FOR NO VOICE RESPONSE 1 FOR VOICE RESPONSE

speaker from playing voice module audio. ◆Alternately, the Console can be programmed to

enable voice module audio. ✍ NOTE: Turning voice response OFF with this

programming step will only effect the audio produced by the voice module. It will not stop the Console’s speaker from sounding local sirens and tones. ✍NOTE: A Model VB-2 or VB-3 Digital Voice

Synthesis module must be installed for this option to function.

REMOTE LOCKOUT

◆ The factory setting for the communicator is to

PROGRAMMING STEP #100

allow remote connection to the Console with Linear’s RA-2400 Remote Access Software and a modem (unlocked). ◆Alternately, the Console can be programmed to

0 FOR UNLOCK 1 FOR LOCK

not answer incoming calls, thereby, not allowing remote access (locked).

Page 36 of the Linear Digital Video Recorder (DVS-2400) user manual — 0 FOR TONE DIALING 1 FOR PULSE DAILING
Page 36 · click to enlarge
Page 36

CALL LIMITER

◆The factory setting for the call limiter is OFF.

This allows the communicator to report burglary alarms, once for each sensor, as many times as they are triggered. ◆Optionally, the Console can be programmed to

PROGRAMMING STEP #101

only allow five burglary reports total per arming period. ✍NOTE: Sensors programmed to 24-hour functions

0 FOR OFF (UNLIMITED) 1 FOR ON (5 VIOLATIONS)

(Emergency, Panic, Fire) always send a Central Station Report and always sound the local siren regardless of the Call Limiter setting.

DIALING DELAY

◆ The factory setting will cause the communicator

to dial the Central Station instantly when an alarm or supervisory event occurs. ◆Alternately, the communicator can be

PROGRAMMING STEP #103

programmed to wait 30 seconds before dialing. This gives the user time to disarm the system and prevent communications in the case of a subscriber generated false alarm.

0 FOR NO DELAY 1 FOR 30 SECOND DELAY

DIALING METHOD

◆ The factory setting causes the communicator to

dial using DTMF (dual-tone multi-frequency) tone dialing. ◆Alternately, the communicator can be

PROGRAMMING STEP #104

4 GHI

programmed to use pulse (rotary) dialing. Use this option if the telephone line in the installation does not support tone dialing.

0 FOR TONE DIALING 1 FOR PULSE DAILING

Page 37 of the Linear Digital Video Recorder (DVS-2400) user manual — FOR ALL PHONE NUMBERS ⇒⇒⇒⇒
Page 37 · click to enlarge
Page 37

COMMUNICATOR REPORTING OPTIONS

REPORTING FORMAT

◆ The factory setting causes the communicator to

report using the 4 by 2 format. This format allows four-digit account numbers from 0000 to 9999 and provides two-digit alarm codes. ◆Alternately ADEMCO CONTACT ID can be

PROGRAMMING STEP #105

5 JKL

chosen as a reporting format. This format allows 4-digit account numbers from 0000 to 9999 and provides verbose report descriptions with Ademco Contact ID compatible Central Stations.

0 FOR 4 BY 2 1 FOR ADEMCO CONTACT ID

CALL ROUTING

◆ The factory setting for the communicator is to

route all calls to the primary telephone number. If communication is unsuccessful after five attempts to the primary number, the secondary number will be dialed for an additional five attempts. If the secondary number cannot be reached, the communicator will “sleep” for five minutes before starting the call process over again. A total of five sleep cycles (50 call attempts) can occur before the communicator stops calling. ◆Alternately, the communicator can be

8 TUV

PROGRAMMING STEP #86

6 MNO

0 FOR ALL TO PRIMARY/SECONDARY 1 FOR ALARMS ONLY TO PRIMARY/SECONDARY

programmed to report supervisory events (low batteries, radio trouble, etc.) to the supervisory telephone number instead of the primary or secondary telephone numbers. ✍CAUTION: If the page alert user code feature is

going to be used, the supervisory number is reserved for the pager number. DO NOT SET THE CALL ROUTING OPTION TO “1”. ◆To disable supervisory reports, set call routing

option to “1” and remove the supervisory telephone number or in 4 by 2 set the report to 0. ✍NOTE: Do not program the primary and secondary

telephone numbers the same. See the FCC Telephone Rules and Regulations on the rear cover of this manual.

COMMUNICATOR REPORTING OPTIONS

STEP # PROGRAMMING

POSSIBLE

FACTORY

INSTALLATION

FUNCTION

VALUES

VALUE

VALUE

0 = ALL CALLS TO PRIMARY OR SECONDARY NUMBER 1 = ALL ALARM CALLS TO PRIMARY OR SECONDARY NUMBER AND ALL OTHERS TO SUPERVISORY NUMBER

86 CALL ROUTING

88 ACCOUNT NUMBER 4 DIGITS EMPTY

89 PRIMARY PHONE NUMBER UP TO 20 DIGITS EMPTY

90 SECONDARY PHONE NUMBER UP TO 20 DIGITS EMPTY

91 SUPERVISORY/ PAGER PHONE NUMBER UP TO 20 DIGITS EMPTY

PRESSING THE (A) KEY INSERTS A 1-SECOND DELAY THE [FIRE] KEY INSERTS A 5-SECOND DELAY THE [CHIME] KEY INSERTS A “*” THE (A) KEY INSERTS A “#” IF IT IS THE LAST DIGIT OF THE PHONE NUMBER

FOR ALL PHONE NUMBERS ⇒⇒⇒⇒

105 REPORTING FORMAT 0 = 4 BY 2; 1 = ADEMCO 0

108 REPORT CONSOLE TROUBLE 0 = NO; 1 = YES 0

110 REPORT FORCE ARMING 0 = NO; 1 = YES 0

111 OPEN/CLOSE 0 = NO; 1 = YES; 2 = MASTER PAC ONLY 0

113 POINT ID REPORTING FOR 4 BY 2 FORMAT 0 = NO; 1 = YES 1

Communicator Reporting Option Table

Page 38 of the Linear Digital Video Recorder (DVS-2400) user manual — ADDS A POUND (#) CHARACTER (END OF NUMBER)
Page 38 · click to enlarge
Page 38

ACCOUNT NUMBER

◆ The communicator’s account number entered

8 TUV

must be 4-digits long. ◆The factory setting for the account number is

PROGRAMMING STEP #88

8 TUV

0000. ◆Enter an account number from 0000 to 9999.

4 DIGIT ACCOUNT NUMBER

PRIMARY TELEPHONE NUMBER

◆ The primary Central Station telephone number

8 TUV

PROGRAMMING STEP #89

can be up to 20-digits long. ◆Digits 0-9 can be used. ◆Delays and special characters can be entered in

9 WXY

the telephone number (see below).

ENTER UP TO 20 DIGITS FOR PRIMARY NUMBER

SECONDARY TELEPHONE NUMBER

◆ The secondary Central Station telephone

9 WXY

number can be up to 20-digits long. ◆Digits 0-9 can be used. ◆Delays and special characters can be entered in

PROGRAMMING STEP #90

the telephone number (see below). ✍ NOTE: To remove the secondary telephone

ENTER UP TO 20 DIGITS FOR SECONDARY NUMBER

number, program Step # then press [TEST].

SUPERVISORY/PAGE ALERT TELEPHONE NUMBER

◆ The supervisory Central Station or pager

telephone number can be up to 20-digits long. ◆Digits 0-9 can be used. ◆Delays and special characters can be entered in

9 WXY

PROGRAMMING STEP #91

the telephone number (see below). ✍ NOTE: To remove the supervisory/page alert

ENTER UP TO 20 DIGITS FOR SUPERVISORY NUMBER

telephone number, program Step # then press [TEST]. ◆If this is a pager number, enter enough delays

(see the number delays and special characters) for the phone to answer. Then enter the number to be dialed. ◆End Page Alert with the completion character,

usually A (#).

TELEPHONE NUMBER DELAYS AND SPECIAL CHARACTERS

◆ When creating telephone numbers with

ADDS A 1-SECOND DELAY (START OR MIDDLE OF NUMBER)

programming Steps 89, 90, & 91, use the following keys to add dialing delays or special characters. ◆Press the (A) key to place a 1-second dialing

ADDS A POUND (#) CHARACTER (END OF NUMBER)

ADDS A 5-SECOND DELAY (ANYWHERE IN NUMBER)

delay at the start or anywhere in the middle of the telephone number. ◆Pressing the (A) key as the last digit of the

ADDS A STAR ( ) CHARACTER (ANYWHERE IN NUMBER)

telephone number will place a pound (#) character at the end of the telephone number. ◆Press the [FIRE] key to place a 5-second dialing

delay anywhere in the telephone number. ◆Press the [CHIME] key to place a star (*

) character anywhere in the telephone number.

Page 39 of the Linear Digital Video Recorder (DVS-2400) user manual — PROGRAMMING STEP #113
Page 39 · click to enlarge
Page 39

REPORT CONSOLE TROUBLE

◆ The factory setting does not report Console

trouble events to the Central Station. ◆ Alternately, the communicator can be

PROGRAMMING STEP #108

programmed to report Console trouble events. These include all conditions that light the Console’s BATTERIES or TROUBLE indicator. It also includes low Console backup battery.

0 FOR NO CONSOLE TROUBLE 1 FOR CONSOLE TROUBLE

REPORT FORCE ARMING

◆ The factory setting does not send force arming

reports. ◆ Alternately, the communicator can be

PROGRAMMING STEP #110

programmed to report force arming anytime the Console is armed with one or more bypassed sensors. ◆The factory set reporting code for force arming is

0 FOR NO FORCE ARMING RPTS. 1 FOR FORCE ARMING RPTS.

“65” (Code 574 with Ademco). ✍NOTE: If force arming is enabled, and the Console

is force armed (armed with an open sensor) remotely by telephone, or with the RA-2400 Remote Access software, the caller will be disconnected if the communicator is enabled.

OPENING AND CLOSING REPORTS

◆ The factory setting does not send opening and

closing reports ◆ Alternately, the communicator can be

PROGRAMMING STEP #111

programmed to send an opening report when the system is disarmed, and a closing report when the system is armed for all users, or just the master user. ✍NOTE 1: For commercial installations using

0 FOR NO OPEN/CLOSE REPORTS 1 FOR O/C RPTS. FOR ALL USERS 2 FOR O/C RPTS. FROM MASTER USER ONLY

opening and closing reports, it is recommended to disable quick arming to prevent customers from arming the system. ✍NOTE 2: The reporting codes are fixed for opening

and closing. A unique code is reserved for the master user code and each of the five restricted user codes. ✍NOTE 3: Arming or disarming with the page alert

user code dials the supervisory number, no opening or closing report is sent.

POINT ID REPORTING

◆ The factory setting enables Point ID and allows

the communicator to send two-digit alarm and trouble codes for each sensor. The individual sensor that causes an alarm or trouble report can be identified at the Central Station. ◆Alternately, Point ID can be disabled. The Central

PROGRAMMING STEP #113

Station will only receive general alarm and trouble reports.

0 FOR GENERAL REPORTS ONLY 1 FOR POINT ID REPORTING

Page 40 of the Linear Digital Video Recorder (DVS-2400) user manual — 0 - 99 FOR SYSTEM REPORTING CODE
Page 40 · click to enlarge
Page 40

COMMUNICATOR REPORTING CODES

◆ The two-digit communicator reporting code for

each event has a factory set value. These values may be customized to fit the specific installation and the reporting requirements of the Central Station monitoring the system. ◆If Point ID reporting is enabled (the factory

HOME TEST = PROGRAM = REMOVE

default setting), each sensor can report a unique alarm and trouble code. ◆If Point ID is disabled, the “general” reporting

AWAY = STORE

codes for each event type will be used. ◆Each programming function is performed with

similar keystrokes. After the Console is in Setup Mode, enter the programming step number, press the [HOME] key (HOME = program), enter the new value, and press the [AWAY] key (AWAY = store). ◆Making a value 0 causes event to not

communicate to central station. ✍NOTE: The reporting codes are fixed for opening

and closing. A unique code is reserved for the master and the five restricted user codes. See the Opening & Closing Reporting Codes Table.

GENERAL REPORTING CODES

◆ Program Steps #201 - 206 for the communicator

reporting codes when Point ID is disabled. ◆Refer to the Console & General Reporting Codes

table to view/edit the reporting codes for each of the five events. The factory settings are listed, along with a blank area to write in the new installation values. ◆Any value from 0-99 can be programmed for

2 ABC

PROGRAMMING STEPS #201 TO #206

each event (0 = no report). ✍NOTE: Be careful not to duplicate codes unless

0 - 99 FOR GENERAL ALARM REPORTING CODE

the Central Station requires specific codes for certain types of events.

SYSTEM REPORTING CODES

◆ Program Steps #261 - 266 for the Console

reporting codes. ◆ Refer to the System Reporting Codes table to

2 ABC

PROGRAMMING STEPS #261 TO #266

6 MNO

view/edit the reporting codes for the keypad [FIRE] and [EMERGENCY] buttons and for each of the four Control Panel conditions. The factory settings are listed, along with a blank area to write in the new installation values.

0 - 99 FOR SYSTEM REPORTING CODE

GENERAL REPORTING CODES

STEP # PROGRAMMING

POSSIBLE

FACTORY

INSTALLATION

FUNCTION

VALUES

VALUE

VALUE

201 GENERAL FIRE REPORT CODE 0 - 99 1

202 GENERAL EMERGENCY REPORT CODE 0 - 99 2

203 GENERAL SILENT PANIC REPORT CODE 0 - 99 3

204 GENERAL BURGLARY REPORT CODE 0 - 99 4

206 GENERAL TROUBLE REPORT CODE 0 - 99 6

General Reporting Codes Table

Page 41 of the Linear Digital Video Recorder (DVS-2400) user manual — 5. CONSOLE INSTALLATION
Page 41 · click to enlarge
Page 41
Linear Digital Video Recorder (DVS-2400) — 5. CONSOLE INSTALLATION diagram (page 41)
Fig. 43

◆Programming Step #258 ◆The factory set reporting code for force arming is

“65” (Code 574 with Ademco). ◆Any value from 0-99 can be programmed for

this event (0 = no report). ✍NOTE: For force arming reporting, force arming

◆Programming Step #259 ◆The factory set reporting code for Duress is “66”

(Code 121 with Ademco). ◆Any value from 0-99 can be programmed for

this event (0 = no report). ✍NOTE: For duress code reporting a keypad duress

Linear Digital Video Recorder (DVS-2400) — 5. CONSOLE INSTALLATION diagram (page 41)
Fig. 44

POSSIBLE 4 x 2 VALUES FACTORY 4 x 2 VALUE ADEMCO

261 SYSTEM FIRE REPORT CODE 0 - 99 68 110

262 SYSTEM EMERGENCY REPORT CODE 0 - 99 69 120

263 SYSTEM TEST/CANCEL REPORT CODE 0 - 99 70 406

264 SYSTEM LOW BATTERY RESTORAL REPORT CODE 0 - 99 71 R302

266 SYSTEM LOW BATTERY REPORT CODE 0 - 99 73 E302

258 FORCE ARMING REPORT CODE 0 - 99 65 574

259 DURESS REPORT CODE 0 - 99 66 121

System Reporting Codes Table

Linear Digital Video Recorder (DVS-2400) — 5. CONSOLE INSTALLATION diagram (page 41)
Fig. 45

MASTER USER CODE 74 82 R401 C000 E401 C000

RESTRICTED USER CODE #1 75 83 R401 C001 E401 C001

RESTRICTED USER CODE #2 76 84 R401 C002 E401 C002

RESTRICTED USER CODE #3 77 85 R401 C003 E401 C003

RESTRICTED USER CODE #4 78 86 R401 C004 E401 C004

RESTRICTED USER CODE #5 79 87 R401 C005 E401 C005

PAGE ALERT USER CODE (DIALS PAGE NUMBER ONLY, NO CODES REPORTED)

REMOTE/HARDWIRE ARM (SENSOR TYPE 9) & QUICK ARM 81 R407 C007

Opening & Closing Reporting Codes Table

Page 42 of the Linear Digital Video Recorder (DVS-2400) user manual — 2 ABC
Page 42 · click to enlarge
Page 42

4 BY 2 FORMAT POINT ID REPORTING CODES

4 BY 2 FORMAT POINT ID ALARM REPORT CODES ◆Refer to the 4 by 2 Format Point ID Reporting

Code table to view/edit the alarm reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled and any sensor triggers an alarm. The factory settings are listed, along with a blank area to write in the new installation values. ✍NOTE: Be careful not to duplicate codes unless

2 ABC

PROGRAMMING STEPS #210 TO #233

the Central Station requires specific codes for certain types of sensors. ◆Each programming function is performed with

0. 99 FOR SENSOR ALARM CODE (0 = NO REPORT)

similar keystrokes. After the system is in Setup Mode, enter the programming step number, press the [HOME] key (HOME = program), enter the new value, and press the [AWAY] key (AWAY = store).

4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES ◆Refer to the 4 by 2 Format Point ID Reporting

Code table to view/edit the trouble reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled and any sensor has a low battery or trouble condition. The factory settings are listed, along with a blank area to write in the new installation values. ✍NOTE: Be careful not to duplicate codes unless

2 ABC

PROGRAMMING STEPS #234 TO 257

0. 99 FOR SENSOR TROUBLE CODE (0 = NO REPORT)

the Central Station requires specific codes for certain types of sensors. ◆Each programming function is performed with

similar keystrokes. After the Console is in Setup Mode, enter the programming step number, press the [HOME] key (HOME = program), enter the new value, and press the [AWAY] key (AWAY = store).

Page 43 of the Linear Digital Video Recorder (DVS-2400) user manual — 5. CONSOLE INSTALLATION
Page 43 · click to enlarge
Page 43
Linear Digital Video Recorder (DVS-2400) — 5. CONSOLE INSTALLATION diagram (page 43)
Fig. 46

210 SENSOR 1 ALARM REPORT CODE 0 - 99 11

211 SENSOR 2 ALARM REPORT CODE 0 - 99 12

212 SENSOR 3 ALARM REPORT CODE 0 - 99 13

213 SENSOR 4 ALARM REPORT CODE 0 - 99 14

214 SENSOR 5 ALARM REPORT CODE 0 - 99 15

215 SENSOR 6 ALARM REPORT CODE 0 - 99 16

216 SENSOR 7 ALARM REPORT CODE 0 - 99 17

217 SENSOR 8 ALARM REPORT CODE 0 - 99 18

218 SENSOR 9 ALARM REPORT CODE 0 - 99 19

219 SENSOR 10 ALARM REPORT CODE 0 - 99 20

220 SENSOR 11 ALARM REPORT CODE 0 - 99 21

221 SENSOR 12 ALARM REPORT CODE 0 - 99 22

222 SENSOR 13 ALARM REPORT CODE 0 - 99 23

223 SENSOR 14 ALARM REPORT CODE 0 - 99 24

224 SENSOR 15 ALARM REPORT CODE 0 - 99 25

225 SENSOR 16 ALARM REPORT CODE 0 - 99 26

226 SENSOR 17 ALARM REPORT CODE 0 - 99 27

227 SENSOR 18 ALARM REPORT CODE 0 - 99 28

228 SENSOR 19 ALARM REPORT CODE 0 - 99 29

229 SENSOR 20 ALARM REPORT CODE 0 - 99 30

230 SENSOR 21 ALARM REPORT CODE 0 - 99 31

231 SENSOR 22 ALARM REPORT CODE 0 - 99 32

232 SENSOR 23 ALARM REPORT CODE 0 - 99 33

233 SENSOR 24 ALARM REPORT CODE 0 - 99 34

234 SENSOR 1 TROUBLE REPORT CODE 0 - 99 41

235 SENSOR 2 TROUBLE REPORT CODE 0 - 99 42

236 SENSOR 3 TROUBLE REPORT CODE 0 - 99 43

237 SENSOR 4 TROUBLE REPORT CODE 0 - 99 44

238 SENSOR 5 TROUBLE REPORT CODE 0 - 99 45

239 SENSOR 6 TROUBLE REPORT CODE 0 - 99 46

240 SENSOR 7 TROUBLE REPORT CODE 0 - 99 47

241 SENSOR 8 TROUBLE REPORT CODE 0 - 99 48

242 SENSOR 9 TROUBLE REPORT CODE 0 - 99 49

243 SENSOR 10 TROUBLE REPORT CODE 0 - 99 50

244 SENSOR 11 TROUBLE REPORT CODE 0 - 99 51

245 SENSOR 12 TROUBLE REPORT CODE 0 - 99 52

246 SENSOR 13 TROUBLE REPORT CODE 0 - 99 53

247 SENSOR 14 TROUBLE REPORT CODE 0 - 99 54

248 SENSOR 15 TROUBLE REPORT CODE 0 - 99 55

249 SENSOR 16 TROUBLE REPORT CODE 0 - 99 56

250 SENSOR 17 TROUBLE REPORT CODE 0 - 99 57

251 SENSOR 18 TROUBLE REPORT CODE 0 - 99 58

252 SENSOR 19 TROUBLE REPORT CODE 0 - 99 59

253 SENSOR 20 TROUBLE REPORT CODE 0 - 99 60

254 SENSOR 21 TROUBLE REPORT CODE 0 - 99 61

255 SENSOR 22 TROUBLE REPORT CODE 0 - 99 62

256 SENSOR 23 TROUBLE REPORT CODE 0 - 99 63

257 SENSOR 24 TROUBLE REPORT CODE 0 - 99 64

Point ID Reporting Codes Table

Page 44 of the Linear Digital Video Recorder (DVS-2400) user manual — IMPORTANT INFORMATION
Page 44 · click to enlarge
Page 44

IMPORTANT INFORMATION

LINEAR LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. For warranty service on Linear equipment return product, at sender’s expense to:

FCC TELEPHONE RULES AND REGULATIONS The FCC requires that this alarm dialer system not make more than 15 repetitive dialing attempts to a single telephone number. There are no limitations when the calls are made sequentially to two or more alternative numbers, or when these calls are spaced 10 minutes apart to a single number. The FCC Rules and Regulations do not specify the re-attempt period as this can vary for specific applications. When setting this period, take into consideration local, interstate, foreign and special network call completion characteristics, network processing time, a sufficient number of rings and busy/don’t answer modes .

FIRE EVACUATION PLANNING For systems that include fire protection, the following information should be available to the users of the system.

✶Draw up a floor plan showing two exits for each room.

Linear Hong Kong 19/F Hounor Industrial Centre 6 Sun Yip Street Chai Wan, Hong Kong Attention: Repairs Department

The following procedures are to be discussed with the family:

➀Status of bedroom doors. ➁Familiarity with alarm signals. ➂Testing of door during a fire and use of alternate escape route if door is

REPAIRS POLICY ✶Charges will be made for equipment that is not of warranty, shows

hot to touch. ➃Crawling and holding breath. ➄Escape fast. No stopping for packing. ➅Meet at designated outdoor spot. ➆Emphasize that no one is to return to a burning house. ➇Fire department notification from a neighbor’s phone. ➈Periodic rehearsal is to be conducted.

customer abuse, or is damaged by the effects of lightning, water, fire, or other abnormal happenings. ✶Customer’s equipment sent in for repair may be repaired or replaced with

new or remanufactured equipment at Linear’s discretion. ✶The customer is always responsible for shipping and handling charges to

the repairs facility. Linear will pay return shipping and handling charges on “in warranty” products shipped back to the customer. The customer will be billed for the return shipping and handling charges on “out of warranty” products. ✶There will be a 50% expedite fee for any express requests. ✶The International Sales Manager must be notified prior to the return of

INDUSTRY CANADA NOTICES NOTICE: The ringer equivalence number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the ringer equivalence numbers of all the devices does not exceed 5. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

product to Linear. All international returns must have an International Repair Authorization number (IRA#). The number must be marked on all packages. Failure to do so will cause delays in processing.

✶The radios are required to comply with local rules and regulations as radio

devices. As such, they have limited transmitter power and therefore limited range. ✶A receiver cannot respond to more than one transmitted signal at a time

and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. ✶Changes or modifications to the device may void regulatory compliance. ✶Infrequently used radio links should be tested regularly to protect against

undetected interference or fault. ✶A general knowledge of radio and its vagaries should be gained prior to

acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users

FCC NOTICE This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

✶Relocate the Console away from the TV/radio receiver. ✶Plug the Console into a different wall outlet so that the Console is on a

different branch circuit. ✶Re-orient the TV/radio antenna. ✶If necessary, the user should consult the dealer or an experienced

radio/television technician for additional suggestions.

Copyright © 2002 Linear Corporation 217157 B

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Linear Digital Video Recorder (DVS-2400)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Digital Video Recorder (DVS-2400)

Be the first to ask — other owners or our team will answer.

Original document

Linear Digital Video Recorder (DVS-2400) manual PDF

44 pages·2.6 MB·Digital Video Recorder·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…