EN
Linear logo
Official user manual

Linear XT-4

2 pages·358 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear XT-4
Table of Contents 80 sections CASE SCREWS AND · SLIDE OUT CIRCUIT · MOUNTED IN SHELTERED · LOCATION WITH ACCESS · … ShowHide
Page 1 of the Linear XT-4 user manual — SYSTEM CODE
Page 1 · click to enlarge
Page 1

CASE SCREWS AND

SLIDE OUT CIRCUIT

If using the ANT-1A antennaFor best range mount the XT/XR unit to a metal plate with a

minimum size of 12" x 12". The ANT-1A antenna should extend above the mounting plate

and be free of obstructions. If the ANT-1A antenna cannot be mounted in the open, consider

using an extension coaxial cable with PL-259 connectors to move the antenna’s location.

The XT/XR series of radios operate in the 27 MHz Citizens Band (CB) and may use any CB

antennas or CB antenna accessories. Antennas, PL-259 extension cables and other

MOUNTED IN SHELTERED

LOCATION WITH ACCESS

TO ANTENNA CO-AX AND

REMOVE FOUR

POWER/SIGNAL WIRES

TWO BOTTOM SCREWS

SCREWS UNTIL WIRING

CASE SCREWS

(DON'T INSTALL TOP

UNIT SHOULD BE

MOUNT UNIT WITH

BOARD

adapters are available at Radio Shack® or other electronics stores.

IS COMPLETE)

2. OPEN TRANSMITTER

END CAP STAYS

ATTACHED TO

THE CIRCUIT

BOARD FITS IN

3RD SLOT UP

CARD FITS IN

REFERENCE

BOARD

1ST SLOT

Linear’s Xtended Range FM transmitters and receivers are designed for use in various

wireless remote control applications. When triggered with an external switch, the Model XT-4

transmitter will send a 10 watt, 27.255 MHz, digital encoded, FSK modulated, signal to its

companion receiver. The receiver will verify the digital code, activate its output, and trigger

The XT-4 transmitter has full supervision capabilities. If the “status” option is selected, the

XT-4 sends hourly status signals to its receiver. If these signals cease, the receiver will

indicate trouble by activating its status output after four hours. Contact supervision allows

the receiver’s outputs to follow the transmitter’s inputs, staying activated as long as each

transmitter input is activated. Alternately, an “auto-restore” option can be selected, causing

a momentary receiver output each time any transmitter input is activated. Each input can be

Power for the XT-4 transmitter can come from an external regulated 12 VDC power supply

(Linear Model T-1224DC) or from a 12-volt battery. A 3-amp fuse protects the unit from

reverse power polarity. The XT-4 draws about 15 μA standby, and about two amps during

MOUNTING BRACKET

FAIR

ANTENNA LOCATION IS

OF PRIMARY CONCERN

UNIVERSAL

OK

POOR

XT-4 WARNING: THIS PRODUCT SHOULD NOT BE USED IN LIFE SAFETY APPLICATIONS. X TENDED RANGE FCC Rules allow unlicensed high-power FOUR CHANNEL transmissions at or near the operating frequency of this product which SUPERVISED may interfere with, or even disable, normal STATIONARY operation of this radio device. TRANSMITTER For Use With Linear’s XR Series Xtended Range Receivers Installation Instructions (760) 438-7000 • FAX (760) 438-7043 USA & Canada (800) 421-1587 & (800) 392-0123 Toll Free FAX (800) 468-1340 www.linearcorp.com1. PRODUCT DESCRIPTION2. OPEN TRANSMITTER Linear’s Xtended Range FM transmitters and receivers are designed for use in various wireless remote control applications. When triggered with an external switch, the Model XT-4 transmitter will send a 10 watt, 27.255 MHz, digital encoded, FSK modulated, signal to its companion receiver. The receiver will verify the digital code, activate its output, and trigger the remote device. The XT-4 transmitter has full supervision capabilities. If the “status” option is selected, the XT-4 sends hourly status signals to its receiver. If these signals cease, the receiver will indicate trouble by activating its status output after four hours. Contact supervision allows the receiver’s outputs to follow the transmitter’s inputs, staying activated as long as each transmitter input is activated. Alternately, an “auto-restore” option can be selected, causing a momentary receiver output each time any transmitter input is activated. Each input can be configured for either N/O or N/C contacts (switch selectable). Power for the XT-4 transmitter can come from an external regulated 12 VDC power supply (Linear Model T-1224DC) or from a 12-volt battery. A 3-amp fuse protects the unit from reverse power polarity. The XT-4 draws about 15 μA standby, and about two amps during transmissions. If the power supply voltage drops below 10.5 volts, a low battery message will be included with any signal transmitted, causing the receiver’s low battery output to activate. Two antennas (sold separately) are available for the XT-4. The Model ANT-1A is an 8-inch “rubber duck” antenna for short range applications (less than 1 mile). The ANT-1A requires a CON-180A (straight) connector to mate the antenna to the transmitter. For a right angle antenna, use the CON-180A plus the CON-90A.The Model ANT-2 is a 3-foot whip antenna for use in long range or difficult installations where more range from the XT-4 is required. A common 9-foot 1/4 wave CB whip antenna can also be used with the XT-4 for maximum range. Two 8-position switches set the unit’s system code. This code must be matched in the XT-4’s receiver. There are 65,536 different system codes possible. The 4-position option switch selects the receiver’s bank (for XR-16 receiver only), and options for status and auto-restore transmissions. The transmitter is housed in a rugged weather-resistant metal enclosure with a sturdy SO-239 antenna connector and a water-tight wiring strain relief bushing. During transmissions, the red operation indicator (visible through a window on the case) lights. If the XT-4’s input voltage is low, the indicator will blink during transmissions.REMOVE FOUR CASE SCREWS AND SLIDE OUT CIRCUIT BOARD REFERENCE CARD FITS IN 1ST SLOT BOARD FITS IN 3RD SLOT UP END CAP STAYS ATTACHED TO THE CIRCUIT CASE SCREWS BOARD 3. COMPONENT LOCATIONS4. INSTALLATION TIPS5. MOUNT TRANSMITTER CASE

configured for either N/O or N/C contacts (switch selectable).

1. PRODUCT DESCRIPTION

the remote device.

PRODUCT SHOULD NOT

SAFETY APPLICATIONS.

transmissions at or near

operation of this radio

WARNING: THIS

BE USED IN LIFE

of this product which

may interfere with, or

device.

X TENDED RANGE

FOUR CHANNEL

TRANSMITTER

For Use With Linear’s

SYSTEM CODE

SUPERVISED

STATIONARY

XR Series Xtended

Range Receivers

SWITCHES

Installation

Instructions

SWITCH "A"

XT-4

LOW BATTERY

INPUT SELECT

(3-AMP 3AG)

TRANSMIT &

INDICATOR

N/O - N/C

SWITCH

SWITCH

RF TEST

BUTTON

OPTION

Show 4 more labels / short text on this page
unlicensed high-power · the operating frequency · FCC Rules allow · even disable, normal
Page 2 of the Linear XT-4 user manual — SET SWITCHES 1 & 2 TO SELECT THE
Page 2 · click to enlarge
Page 2

This Linear product is warranted against defects in material and workmanship

for twelve (12) months. The Warranty Expiration Date is labeled on the product.

This warranty extends only to wholesale customers who buy direct from Linear or

through Linear’s normal distribution channels. Linear does not warrant this product

to consumers. Consumers should inquire from their selling dealer as to the nature of

the dealer’s warranty, if any. There are no obligations or liabilities on the part of

Linear LLC for consequential damages arising out of or in connection with use

or performance of this product or other indirect damages with respect to loss of

property, revenue, or profit, or cost of removal, installation, or reinstallation. All

implied warranties, including implied warranties for merchantability and implied

warranties for fitness, are valid only until Warranty Expiration Date as labeled on the

product. This Linear LLC Warranty is in lieu of all other warranties express or

All products returned for warranty service require a Return Product Authorization

Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#

Linear radio controls provide a reliable communications link and fill an important need

in portable wireless signaling. However, there are some limitations which must be

1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

Copyright © 2005 Linear LLC 215284 C

1 WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow unlicensed high-power transmissions at or near the operating frequency of this product which may

1 Changes or modifications to the device may void FCC compliance. 1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault. 1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

TO UNIT

1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95 Radio Control devices. As such, they have limited transmitter power and therefore limited range.

CONNECTOR CON-180A + CON-90A

ANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED.

APPLICATIONS CON-180A

STRAIGHT

AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THE

(A METAL MOUNTING POLE IS RECOMMENDED)

USE RG-8 FOR UP TO 100-FOOT CABLE RUNS.

6. SET TRANSMITTER SWITCHES 7. CONNECT POWER AND TRIGGER INPUTS 8. MOUNT ANTENNA AND ROUTE CABLE

MOUNT ANTENNAS AS HIGH AS POSSIBLE

USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGER

interfere with, or even disable, normal operation of this radio device.

ANGLE CONNECTOR

IMPORTANT !!!

ANTENNA USE ANT-1A ANTENNA

RANGE APPLICATIONS OR DIFFICULT

ANT-1A

FOR SHORT RANGE (LESS

INSTALLATIONS

and other important details.

THAN 1 MILE)

implied.

observed.

SET INPUT SELECT SWITCH

TO MATCH INPUT TYPE FOR

6. SET TRANSMITTER SWITCHES7. CONNECT POWER AND TRIGGER INPUTS8. MOUNT ANTENNA AND ROUTE CABLE SET OPTION SWITCH RECEIVER BANK STATUS REPORTS SWITCH 1 SWITCH 2 BANK # SWITCH 3 OFF OFF 1 OFF NO STATUS REPORTS ON OFF 2 ON STATUS REPORTS OFF ON 3 ON ON 4 SET SWITCHES 1 & 2 TO SELECT THE AUTO RESTORAL RECEIVER BANK THE TRANSMITTER SWITCH 4 ACTIVATES (USED ONLY FOR 16 CHANNEL OFF MANUAL RESTORE RECEIVER, USE BANK 1 FOR ALL OTHERS) ON AUTO RESTORE SYSTEM CODE SWITCHES SET SYSTEM CODE SWITCHES A & B TO MATCH SYSTEM CODE SWITCHES A & B IN THE RECEIVER SWITCH "A" SWITCH "B" OPTION SWITCHSET INPUT SELECT SWITCH TO MATCH INPUT TYPE FOR EACH CHANNEL INPUT SELECT SWITCH SWITCH # CHANNEL OFF =ON = SWT 1 CH 1 N/O N/C SWT 2 CH 2 N/O N/C SWT 3 CH 3 N/O N/C SWT 4 CH 4 N/O N/C SET SWITCHES 1 - 4 TO SELECT THE NORMAL (NON-VIOLATED) STATE OF THE INPUT TRIGGER DEVICE SWITCH OFF = N/O SWITCH ON = N/C ROUTE WIRES THROUGH CASE STRAIN RELIEF BUSHING BEFORE CONNECTING TO TERMINALS USE 18-24 AWG WIRE TO CONNECT POWER AND TRIGGER INPUTS CAUTION: BE SURE WIRE STRANDS DO NOT TOUCH NEARBY FUSE VDC GND 12 GND CH 1 GND CH 2 GND CH 3 GND CH 4 + FOR RUNS LONGER THAN 3' CONNECT THE SUPPLIED 10K Ω RESISTOR FROM THE +12V WARNING SUPPLY TO THE "INPUT" TERMINAL OF THE SENSOR SWITCH THIS UNIT REQUIRES 12 VDC AT 2 AMPS. FROM 12 VDC, 2-AMP THE NO-LOAD VOLTAGE OF THE SUPPLY REGULATED POWER NOTE: MAXIMUM POWER WIRE MUST NOT EXCEED 17.5 VDC OR DAMAGE SOURCE RUN 25-FEET WITH 18 AWG WIRE TO THE UNIT WILL OCCUR!ANT-1A USE ANT-1A ANTENNA ANTENNA FOR SHORT RANGE (LESS THAN 1 MILE) APPLICATIONS CON-180A STRAIGHT CONNECTOR CON-180A + CON-90A ANGLE CONNECTOR USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGER RANGE APPLICATIONS OR DIFFICULT INSTALLATIONS MOUNT ANTENNAS AS HIGH AS POSSIBLE (A METAL MOUNTING POLE IS RECOMMENDED) AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THE ANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED. USE RG-8 FOR UP TO 100-FOOT CABLE RUNS. TO UNIT 9. TEST SYSTEM10. COMPLETE INSTALLATIONLINEAR LIMITED WARRANTY

EACH CHANNEL

RECEIVER BANK SWITCH 1 SWITCH 2 BANK OFFOFF 1 ON OFFOFF 2 ON 3 ONON 4 SET SWITCHES 1 & 2 TO SELECT THE RECEIVER BANK THE TRANSMITTER ACTIVATES (USED ONLY FOR 16 CHANN RECEIVER, USE BANK 1 FOR ALL OTHER
INPUT SELECT SWITCH SWITCH # CHANNEL OFF =ON = SWT 1CH 1N/ON/C SWT 2CH 2N/ON/C SWT 3 SWT 4CH 3 CH 4N/O N/ON/C N/C SET SWITCHES 1 - 4 TO SELECT THE NORMAL (NON-VIOLATED) STATE OF THE INPUT TRIGGER DEVICE SWITCH OFF = N/O SWITCH ON = N/C

USE 18-24 AWG WIRE

ON =

N/C

N/C

N/C

N/C

SWITCH OFF = N/O SWITCH ON = N/C

NORMAL (NON-VIOLATED) STATE OF THE

STRAIN RELIEF BUSHING BEFORE

SWITCH # CHANNEL OFF =

SET SWITCHES 1 - 4 TO SELECT THE

ROUTE WIRES THROUGH CASE

INPUT SELECT SWITCH

SWT 1 CH 1 N/O

SWT 2 CH 2 N/O

SWT 3 CH 3 N/O

SWT 4 CH 4 N/O

CONNECTING TO TERMINALS

INPUT TRIGGER DEVICE

SET SYSTEM CODE SWITCHES A & B TO

MATCH SYSTEM CODE SWITCHES A & B

ON NO STATUS REPORTS

STATUS REPORTS

STATUS REPORTS

AUTO RESTORAL

ON MANUAL RESTORE

SYSTEM CODE SWITCHES

AUTO RESTORE

SWITCH 3

SWITCH 4

SET OPTION SWITCH

OFF

OFF

IN THE RECEIVER

ACTIVATES (USED ONLY FOR 16 CHANNEL

RECEIVER, USE BANK 1 FOR ALL OTHERS)

TRANSMITTER'S INPUT

TRANSMITTER IS TRIGGERED

SWITCH 1 SWITCH 2 BANK #

NEVER CONNECT THE TRANSMITTER AND

THE TRANSMIT INDICATOR

OFF OFF 1

ON OFF 2 OFF ON 3 ON ON 4

SET SWITCHES 1 & 2 TO SELECT THE

RECEIVER BANK THE TRANSMITTER

DAMAGE TO BOTH UNITS WILL OCCUR!

SHOULD LIGHT WHEN THE

RECEIVER ANTENNA CONNECTORS

DIRECTLY TO EACH OTHER. MAJOR

RECEIVER BANK

SLIDE BOARD INTO

CASE IN THE 3RD

WARNING

OPTION SWITCH

SLOT UP

Ask about the Linear XT-4

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear XT-4

Be the first to ask — other owners or our team will answer.

Original document

Linear XT-4 manual PDF

2 pages·358 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…