EN
Linear logo
Official user manual

Linear Garage Door Remote (1050)

2 pages·38 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear Garage Door Remote (1050)
Table of Contents 9 sections DIGITAL TRANSMITTER MODEL 1050 · INSTALLATION INSTRUCTIONS · ACCESSING THE CODE SWITCH · LINEAR CORPORATION · … ShowHide
Page 1 of the Linear Garage Door Remote (1050) user manual — LINEAR CORPORATION
Page 1 · click to enlarge
Page 1

Congratulations! You have just purchased a Linear Digital Transmitter, which we

believe to be the finest product of its kind on the market. With a little care this

transmitter should provide you with many years of excellent service. Please take a

moment to read the following instructions and you will find that setting your new

On the model 1050 the side of the transmitter is removable. Squeeze the ends

of the transmitter case or twist a coin in the slot provided, then pull the side to

remove it. This will expose both the code switch and battery compartment.

DIGITAL TRANSMITTER MODEL 1050

INSTALLATION INSTRUCTIONS

transmitter will be quite an easy matter.

ACCESSING THE CODE SWITCH

To check operation, move back a reasonable distance (about 50 ft.) and press the

transmitter button. Operation should be reliable at this distance but

environment and location of both the transmitter and receiver will affect the

range. If the transmitter is stowed well out of sight, it may be necessary to

remove it from its mounting and hold near the windshield. Try different locations

1. Checking the door operator. If the door will not open when the wall button is pressed, the problem is likely to be the operator. If the door will open by pressing

the wall button, but not when the radio control button is pressed, the problem is

2. Replacing the transmitter battery. If after performing the above operational checks, the controls still do not function, they should be returned to your dealer for

radiators which are not expressly approved by LINEAR CORPORATION could

void the user’s authority to operate this equipment. This applies to intentional

and unintentional radiators certified per part 15 of the F.C.C. rules and

Copyright © 1999 Linear Corporation 216908 A

and positions. If operation is still unsatisfactory, the problem may be isolated by:

2055 Corte del Nogal • Carlsbad, CA 92009 (760) 438-7000

LINEAR CORPORATION

OPERATIONAL CHECK

probably in the radios.

repair or replacement.

regulations.

Page 2 of the Linear Garage Door Remote (1050) user manual — SELECTING A CODE
Page 2 · click to enlarge
Page 2

The transmitter is completely self contained, including battery, and can be

operated while mounted in the car. It is supplied with a clip for attaching to the

sun visor, if desired. If the clip is used attach to the case by sliding it into the

recess provided on the back of the transmitter until the small dimples fit into the

The battery in the transmitter can be checked or changed by removing side of the

transmitter. Refer to the directions under “accessing the code switch” for battery

A replacement or new transmitter or receiver may be purchased by specifying

the Model Number and the RF frequency designated on the identification label.

The RF frequency is set at the factory and must not be adjusted in the field. The

digital code can be matched to the companion receiver or transmitter by

Replacement battery - 9 volt NEDA 1604 (Eveready 216 or equivalent).

TRANSMITTER BATTERY REPLACEMENT

TRANSMITTER INSTALLATION

TO REPLACE OR ADD A SET

following the above procedure.

holes in the clip.

replacement.

You may set your transmitter to any code you desire but be sure that the code you

set matches the code that has been set on your radio receiver. The digital code is

determined by the positions of the 10 small switches numbered 1 through 10

located in the receiver and transmitter. Any combination of ON (CLOSED) or OFF

(OPEN) positions can be selected by using a small screwdriver or paper clip.

(NOTEThe switches are in the “On” position when the side next to the number

is pressed in.) In setting your own personal code we strongly urge that several

coding schemes be avoided: ALL ON; ALL OFF; 2,4,6,8,10 ON; 1,3,5,7,9 ON.

These positions are similar to our or other manufacturer’s test positions, or are

frequently used. Once the code has been set, check the operation and replace

SELECTING A CODE

the case side.

Ask about the Linear Garage Door Remote (1050)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Garage Door Remote (1050)

Be the first to ask — other owners or our team will answer.

Original document

Linear Garage Door Remote (1050) manual PDF

2 pages·38 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…