EN
Linear logo
Official user manual

Linear Garage Door Remote (3060)

2 pages·35 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear Garage Door Remote (3060)
Table of Contents 19 sections MINI-TRANSMITTER MODEL 3060 · ACCESSING THE CODE SWITCH AND BATTERY · INSTALLATION INSTRUCTIONS · COMPARTMENT · … ShowHide
Page 1 of the Linear Garage Door Remote (3060) user manual — LINEAR CORPORATION
Page 1 · click to enlarge
Page 1

Congratulations! You have just purchased a Mini-Code

Digital Transmitter, which we believe to be the finest

product of its kind on the market. With a little care this

transmitter should provide you with many years of

excellent service. Please take a moment to read the

following instructions and you will find that setting your

The model 3060 Mini-Transmitter case is composed of 2

halves which are held together by a small phillips head

screw. Removing this screw will allow access to both the

code setting switch and the battery compartment. (see

MINI-TRANSMITTER MODEL 3060

ACCESSING THE CODE SWITCH AND BATTERY

INSTALLATION INSTRUCTIONS

new transmitter will be quite an easy matter.

COMPARTMENT

location of both the transmitter and receiver will affect

the range. If the transmitter is stowed well out of sight, it

may be necessary to remove it from its mounting and

hold near the windshield. Try different locations and

positions. If operation is still unsatisfactory, the problem

1. Checking the door operator. If the door will not open when the wall button is pressed, the problem

is likely to be the operator. If the door will open by

pressing the wall button, but not when the radio

control button is pressed, the problem is probably in

2. Replacing the transmitter battery. If, after performing the above operational checks, the controls still

do not function, they should be returned to your

unintentional radiators which are not expressly approved by

LINEAR CORPORATION could void the user’s authority to

operate this equipment. This applies to intentional and

unintentional radiators certified per part 15 of the F.C.C.

This device complies with FCC Part 15 and Industry Canada

Rules and Regulations. Operation is subject to the following

two conditions(1) This device may not cause harmful

interference, and (2) This device must accept any

interference received, including interference that may cause

Copyright © 2000 Linear Corporation 214942 B

2055 Corte Del Nogal • Carlsbad, CA 92009

LINEAR CORPORATION

dealer for repair or replacement.

rules and regulations.

may be isolated by:

undesired operation.

the radios.

® · diagram #1)

Page 2 of the Linear Garage Door Remote (3060) user manual — SWITCH
Page 2 · click to enlarge
Page 2

Once the codes have been set, check operation and

This transmitter is completely self contained, including

battery and can be operated while held in hand or while

mounted in the car. It is supplied with “hook and loop”

fabric for easy mounting or it may be added to your key

Replacement battery - 12 volt alkaline lighter battery

The transmitter battery can be checked or changed by

removing the phillips head screw located on the back of

the case and carefully separating the case halves to

expose the circuit board and battery. Simply slide out the

old battery and slide in the new, remembering to observe

the battery polarity molded on the case in the bottom of

the battery compartment. Note that if the red L.E.D. on

your transmitter fails to light you most likely have a weak

or dead battery and it should be replaced. (see diagram

To check operation, move back a reasonable distance

(about 50 ft.) and press the transmitter button. Operation

should be reliable at this distance but environment and

TRANSMITTER BATTERY REPLACEMENT

MINI-TRANSMITTER INSTALLATION

reassemble the transmitter case.

(Eveready A 23 or equivalent)

chain using the slot provided.

OPERATIONAL CHECK

Set both transmitter and receiver switches to the code of

your choice, being sure both are set the same since a

different setting of just one switch will prevent

operation. The digital code is determined by the position

of 10 small switches numbered 1 through 10 located in

the receiver and transmitter. Any combination of “on” or

“off” positions can be selected by using a pencil or ball

point pen. (NoteThe switches are in the “on” position

when the switch is depressed toward the number.) See

1 2 3 4 5 6 7 8 9 1 0 ON

TRANSMITTER TOP COVER

DIAGRAM #1

DIAGRAM #2

CODE SWITCH

TRANSMITTER WITH TOP

HALF OF CASE REMOVED

BATTERY

SELECTING A CODE

diagram # 2.

SWITCH

CODE

OFF

#1)

Ask about the Linear Garage Door Remote (3060)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Garage Door Remote (3060)

Be the first to ask — other owners or our team will answer.

Original document

Linear Garage Door Remote (3060) manual PDF

2 pages·35 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…