EN
Linear logo
Official user manual

Linear Garage Door Remote (1051)

2 pages·24 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear Garage Door Remote (1051)
Table of Contents 17 sections Before Installation · Important! Read · TRANSMITTER · SAFETY EDGE · … ShowHide
Page 1 of the Linear Garage Door Remote (1051) user manual — LINEAR CORPORATION
Page 1 · click to enlarge
Page 1

The MULTI-CODE 1051 transmitter has been

designed to provide great reliability and safety, but it must

be installed correctly. Read the enclosed instructions

The Model 1051 may be used for a variety of purposes,

and wherever remote signaling is desirable, as specified

by FCC regulations. If this transmitter is to be used in an

application which may be safety related be sure to take

special precautions. Linear Corporation has taken every

step to insure the best possible product, but you must be

Before installing the 1051 transmitter, open it up by

removing the four screws which secure the top of the case.

You will note that there is a terminal block (see figure 1), to

which you will secure the wires coming from your device.

Run your wire through the strain relief fitting, leaving

enough wire to provide adequate length for stripping.

YOUR WIRE SHOULD BE 18 TO 24 GAUGE, although any

wire that fits snugly in the strain relief fitting may be used.

Be sure to check the water-tightness of the fitting if you use

anything other than 18-24 gauge wire, as this may

compromise the integrity of the case. Put your two wires

Next, code your transmitter and, if necessary, your

receiver. The code switch (see figure 1) allows for 1024

possible combinations. If you have an existing receiver, you

may code the 1051 to the same code, or you may choose to

wire a separate receiver. If you wire a second receiver, be

sure to separate the two receivers as much as possible, to

under the terminal blocks, and fasten by screwing down.

Before Installation

Important! Read

certain to install the 1051 transmitter correctly.

TRANSMITTER

SAFETY EDGE

Model 1051

avoid any possibility of interference.

carefully.

3. You should test your entire system occasionally in

order to be sure that all components are working in

4. Linear Corporation’s dealers can provide you with

information regarding the use of our radio controls,

and can provide valuable installation and operation

which are not expressly approved by LINEAR CORPORATION could void the

user’s authority to operate this equipment. This applies to intentional and

unintentional radiators certified per Part 15 of the F.C.C. rules and regulations.

Copyright © 1999 Linear Corporation 216977 A

For service, return to your dealer or shop prepaid to:

LINEAR CORPORATION

2055 Corte del Nogal Carlsbad, CA 92009

information, when requested.

good order.

®

Page 2 of the Linear Garage Door Remote (1051) user manual — MTG. HOLE
Page 2 · click to enlarge
Page 2

The 1051 Transmitter needs a minimum of care,

1. Be sure to check the 1051 Transmitter as a system. Be sure that the device that is connected to the 1051 is

functioning with the transmitter, and with the

2. Check the system to which the 1051 is attached frequently.
3. The 1051 employs long life Alkaline-Manganese Dioxide Batteries (Eveready Energizer 522 or equivalent). Nominal

life for these batteries is three years, but we suggest you

test the unit more often than this. Test the transmitter any

time you perform maintenance on the rest of the system.

MULTI-CODE products products carry an eighteen (18) month

warranty against defects in workmanship or material. This

warranty begins at the date of manufacture, for eighteen

months. Linear Corporation warrantees our product only to

our authorized dealers and distributors, and not to the end

customer. If you have questions about our warranty, please

ask your dealer to determine the nature and scope of his

warranty. Linear Corporation does not assume, and is not

responsible for, any real or consequential damages from

claims against the performance of our product, nor is it

liable for any costs related to loss of life, property, or

revenue. Further, Linear Corporation is in no way

responsible for installation of our product, and will assume

no costs to reinstallation or removal. Linear

Corporation’s Warranty is in lieu of all other warrantees, ex-

Linear Corporation has devoted a great deal of time and

research in order to provide the most reliable equipment

1. MULTI-CODE radio components must conform with

FCC Part 15 requirements. For this reason, the range

2. As with all manufacturers, MULTI-CODE radios

must accept all signals that they receive. This may, in

and power of our radios is within specified limits.

possible. Certain limitations must be observed.

however, certain precautions must be taken:

MAINTENANCE

WARRANTY

rare instances, create difficulty.

pressed, or implied.

PLEASE NOTE

receiver.

If you are going to use the 1051 transmitter in a safety

related device, be sure to read the manufacturer’s

instructions with regard to wiring and limitations of the

After you have wired and coded the 1051, you are now

ready for mounting. You will note that there are four holes

in the case, through which you can mount your screws,

rivets, or other mounting devices. If the transmitter is to be

used in the proximity of metal, be sure to test the location at

the greatest distance the device will be from its receiver, in

order to be sure that adequate performance is achieved.

ANY METAL, INCLUDING MOUNTING PLATES, ETC., MAY

AFFECT THE PERFORMANCE OF YOUR TRANSMITTER.

Once you are satisfied with the performance of the radio,

Linear Corporation has taken every precaution to

assure that the 1051 will perform reliably. In order to

provide the greatest reliability, we have fastened the

printed circuit board to the case with a special fastening

agent, such as Loctite. We suggest that you use a similar

material to your fastening screws if vibration is likely to be

Before releasing the radio transmitter for use, test the system for

associated hardware. The system should be tested at various

positions of travel of the gate member to be certain that the gate

functioning to detect an obstruction and reverse or stop the

MTG. HOLE MTG. HOLE

MTG. HOLE

proper operation after installing the radio transmitter and

… IMPORTANT SAFETY TEST …

edge, radio transmitter, receiver and gate operator are

CODE SWITCH

STRAIN RELIEF

you can permanently mount it.

TERMINAL BLOCK

safety circuit.

encountered.

MTG. HOLE

BATTERY

gate.

Ask about the Linear Garage Door Remote (1051)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Garage Door Remote (1051)

Be the first to ask — other owners or our team will answer.

Original document

Linear Garage Door Remote (1051) manual PDF

2 pages·24 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…