Instruction/ maintenance manual of the product Q25DVR4ES Q-See
Go to page of 25
Q-See Q25DVR4ES User ’ s Manual Page 1 Q25DVR 4ES Econo m y Series User Manual Contact Us : Q-See Products 8015 E. Cr ystal D r Anaheim, CA 92807 W ebsite: http://www .q-see.com Customer Ser vice: Phone: 877-998- 3440 x 538 Email: cs@dpsi-usa. com T ec h Support: Phone: 877-998- 3440 x 539 Email: ts@dpsi-u sa.
Q-See Q25DVR4ES User ’ s Manual Page 2 1. DVR Feature s .. ... .. .. .. .. .. .. .. ... .. .. .. .. ... .. .. ... .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. ... .. .. ... .. .. .. ... .. .. .. .. . 3 2. Layout . .. .. ..
Q-See Q25DVR4ES User ’ s Manual Page 3 4 Channel BNC Camera Input. 1 Channel BNC V ideo Output. V ideo Source Option: NTSC / P AL. Motion Detection with Sensitivity and Area Settings. T i me Schedule Reco rding / Motion T riggered Recording.
Q-See Q25DVR4ES User ’ s Manual Page 4 01. CH1 Select or enlarge CH1 02. CH2 Select or enlarge CH2 03. CH3 Select or enlarge CH3 04. CH4 Select or enlarge CH4 05. QUAD Quad V ie w 06. Rewind 07. Play recording list 08. Forward 09. Record 10. Pause 1 1.
Q-See Q25DVR4ES User ’ s Manual Page 5 NOTE: This package comes w ith a 250GB hard drive. Y ou would follow these i nstructions if you want or need to install a new hard drive. 1. Slide the HDD tray out of DVR body carefully . 2. Connect the power c ord and data cable to hard disk drive carefully .
Q-See Q25DVR4ES User ’ s Manual Page 6 There are 4 camera inputs a nd 1 video output with BNC connectors (Refer to Chapter 2: Layout- 2.2 Rear Panel).
Q-See Q25DVR4ES User ’ s Manual Page 7 Chapter 4 : System Boot - 4.2 Recovering Lost Data The s y s tem will automatically recov er lost data. A Power Error can cause data to be lost.
Q-See Q25DVR4ES User ’ s Manual Page 8 Menu Dir ectory CAMERA SELECT RECORD SELECT RESOLUTION RECORD FRAME VIDEO QUALITY SCHEDULE SET MISCELLANEOUS MENU HARD DISK SET MOTION SET F ACTOR Y RESET Chapte r 5: DVR Setup - 5.
Q-See Q25DVR4ES User ’ s Manual Page 9 Configure which channels are allowed to r ecord. Note: If no channels are selected, an error message will appear briefl y o n th e scr een when record is selected. There ar e two modes of r esolution for video re cording: 1.
Q-See Q25DVR4ES User ’ s Manual Page 10 [ QUAD ] button and hold for three (3) s econds t o make each video cha nnel enlarge to full screen . The full screen will be d isplayed for thre e (3) s econds, including Qu ad view . The Loop F unction will co ntinue until any bu tton is pushed .
Q-See Q25DVR4ES User ’ s Manual Page 1 1 User can setup video recording m ethod b y T ime, Motion T riggered and Continuous Recording. When the function is set to be “ ON ”, DVR will be awaked to record autom aticall y b y schedule if DVR is without any manual operations in five m inutes.
Q-See Q25DVR4ES User ’ s Manual Page 12 System default password: Pre ss [ CH1] button six times. Chapter 5: DVR Setup - 5.10 Sub Men u-Passwo rd Change User needs to enter six characters for the password. All ke y s can be used as password key except the [ Menu] key , which is used to exit.
Q-See Q25DVR4ES User ’ s Manual Page 13 HDD FORMA T : If y ou format the hard drive, it will erase all the data on the hard drive . Note: When y ou install a new hard drive in the DVR, please use this fu nction to format the hard drive. Chapte r 5 : DVR Setup - 5.
Q-See Q25DVR4ES User ’ s Manual Page 14 After com pleting the “MOTION SETUP ”, User can exit by clicking [ Menu] , and press [ Rec ord] to start Motion Recording. Chapte r 5: DVR Setup - 5.14 Motion Setup CHANNEL SENSITIV ITY : Press [ Select] to adjus t sensitivity of motion de tection on each channel.
Q-See Q25DVR4ES User ’ s Manual Page 15 Change the J10 jumper on the sy ste m boa rd to select NTSC or P AL video output as marked on the silkscreen of the sy stem board. Press the [ SEL ] Bu tton to reload factory def aults, then the DVR will reboot, all custo m settings (including password) will be restored to default .
Q-See Q25DVR4ES User ’ s Manual Page 16 Press [ Record ] to start recording (As set in 5.7 Schedule Set ). System will display in formation on Screen. NOTE: Onl y EACH Mode can enlarge si ngle channel to full screen displa y . 1. Hard Drive Usage (Displa y e d as a percentage) 2.
Q-See Q25DVR4ES User ’ s Manual Page 17 Estimated record time based on a 120GB Ha rd Drive (Quad Mode) Unit: Hour Estimated record time based on a 120GB Ha rd Drive (Quad Mode) in hours: 120 (G B y t e) x 1024 (M B y t e) x 1024 (K By te) Divided by : 15 (K B y te/ frame) x 7 (f ram e/sec.
Q-See Q25DVR4ES User ’ s Manual Page 18 4 1. S tart Time. 2. End Tim e. 3. TIME: Continuous record. 4. MOTION: M otion T riggered event. 5. Un-played video recording. 1. Put the U SB Driver Pro gram CD i n your CD-ROM Drive. 2. Open CD directory . 3.
Q-See Q25DVR4ES User ’ s Manual Page 19 Chapte r 8: USB DVR Access - 8.2 Program but tons.
Q-See Q25DVR4ES User ’ s Manual Page 20 1. DVR Event Lis t 2. Capture one frame picture 3. Save DV R’ s Recorded V ideo to PC 4. Configuration 5. Load V ideo File Saved i n PC 6. Play DVR V ideo File 7. Play PC V ideo File 8. Channel Selection Key s 9.
Q-See Q25DVR4ES User ’ s Manual Page 21 Press to configure the DVR play/r ecord system. Press to print the pictur e of DVR’ s playback Press to play the video .
Q-See Q25DVR4ES User ’ s Manual Page 22 D VR Specifications ITEM DESCRIPTION NOTE V ideo Format NTSC / P A L Operation Sys tem None ST AND-AL ONE Camera Input Cha nnel 4 channel Comp osite BNC V ide.
Q-See Q25DVR4ES User ’ s Manual Page 23 Chapte r 10: A ppendix - 10.1 System Connection Diagram.
Q-See Q25DVR4ES User ’ s Manual Page 24 Q-SEE Product Wa rranty Chapte r 10: A ppendix - 10.2 DVR Accessories (included).
Q-See Q25DVR4ES User ’ s Manual Page 25 Thank you f or choosing our product s. All of our products users have a conditiona l free warra nty repair service for har dware within 12 m onths starting from purchase da te, a nd a free exchange service within one month (valid for manufacturing defects).
An important point after buying a device Q-See Q25DVR4ES (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Q-See Q25DVR4ES yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Q-See Q25DVR4ES - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Q-See Q25DVR4ES you will learn all the available features of the product, as well as information on its operation. The information that you get Q-See Q25DVR4ES will certainly help you make a decision on the purchase.
If you already are a holder of Q-See Q25DVR4ES, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Q-See Q25DVR4ES.
However, one of the most important roles played by the user manual is to help in solving problems with Q-See Q25DVR4ES. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Q-See Q25DVR4ES along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
