EN
Linear logo
Official user manual

Linear TMD-90

2 pages·193 KB·Home Security System·PDF·ENDEFRITNLJA
Linear TMD-90
Table of Contents 80 sections STEP 8 Replace cover. Replace the case cover. Press the · the various components. STEP 3 Remove circuit board. Remove the adjustment · STEP 7 Set option switches. Set the option switches to · select the number of pulses and time frame for alarm. Set · … ShowHide
STEP 8 Replace cover. Replace the case cover. Press thep.1the various components. STEP 3 Remove circuit board. Remove the adjustmentp.1STEP 7 Set option switches. Set the option switches top.1select the number of pulses and time frame for alarm. Setp.1DESCRIPTION The TMD-90 is a passive infrared (PIR)p.1STEP 6 Replace board. Replace the circuit board andp.1ANTENNAp.1ADJUSTMENTp.1WALK TESTp.1FOUR TYPE "AA"p.1REMOVE THEp.1PROTECTIONp.1DETECTORp.1INFRAREDp.1BATTERIESp.1REPLACEp.1BATTERYp.1LEDp.1POST CENTER DETECTIONp.1STRIPp.1POSTp.1TRANSMITTERp.1PATTERN POINTERp.1ON ADJUSTMENTp.1USE DURACELLp.1TOSHIBA LR6Gp.1"AA" ALKALINEp.1TEST BUTTONp.1MN1500 ORp.1SWITCHp.1NOTE:p.1ONLY!p.1TAMPERp.1OPTIONp.1STEP 1 Open detector case. Press in the locking tab andp.1STEP 5 Mount case. Attach the case to the wall using thep.1screws and screw anchors provided. Mount the detector in ap.1location where the intruder’s path will likely cross thep.1LOCKING TABp.1OPENp.1CASEp.1FORMAT!p.1PUSH INp.1SXp.1ANCHORS TO MOUNTp.1USE SCREWS ANDp.1(760) 438-7000 • FAX (760) 438-7043p.1CASE TO WALLp.1SUPERVISED WIRELESSp.1CASE POINTSp.1ARROW ONp.1TO TOPp.1TMD-90p.1PASSIVE INFRAREDp.1MOTION DETECTORp.1Installation Instructionsp.17 FEET FROM FLOORp.1APPROXIMATELYp.1STEP 12 Replace and lock cover. Replace the unit’sp.2CLOSEp.2INSERT LOCKINGp.2Optional Horizontal Curtain Lens See the figure forp.2WITH SMOOTH SIDEp.2PRY TABS UP TOp.2INSERT NEW LENSp.2REMOVE LENSp.2SIDE VIEWp.2SCREWp.2BRACKETp.2OUTp.2TOPp.2VIEWp.2LINEAR LIMITED WARRANTYp.2WILL SNAP SHUTp.2HORIZONTALp.2CURTAIN LENSp.2STEP 11 Program transmitter into receiver. Refer to thep.2instructions supplied with the supervised receiver to program thep.2TMD-90 as a non-restoring PIR sensor. Turn the walk test switchp.2Optional Long Range Lens See the figure forp.2
Page 1 of the Linear TMD-90 user manual — 7 FEET FROM FLOOR
Page 1 · click to enlarge
Page 1
Linear TMD-90 — STEP 8 Replace cover. Replace the case cover. Press the diagram (page 1)
Fig. 1 · STEP 8 Replace cover. Replace the case cover. Press…

post and remove the circuit board. STEP 4 Punch out knockouts. Use a small Phillips

screwdriver to punch out the desired case mounting knockouts.

STEP 8 Replace cover. Replace the case cover. Press the

The transmitter is powered by four Duracell “AA” MN1500 1.5-volt

alkaline batteries (included) and can power the unit for up to 5 years.

When the battery voltage gets low, a low battery report is sent to the

the various components. STEP 3 Remove circuit board. Remove the adjustment

STEP 7 Set option switches. Set the option switches to

select the number of pulses and time frame for alarm. Set

switches 2 & 5 ON, 1, 3 & 4 OFF. Set switch #6 ON to select

DESCRIPTION The TMD-90 is a passive infrared (PIR)

motion detector with a built-in supervised, digitally-coded radio

The PIR detects motion in its detection pattern by measuring the

infrared emission levels of objects that it “sees”. If the infrared levels

change quickly, as when a person moves across the detection

A selectable “pulse count” circuit controls the PIR’s triggering of the

transmitter. As a person moves across the detection pattern, the PIR

registers one pulse as each “finger” of the detection pattern is

crossed. The TMD-90 counts these pulses. When the selected

number of pulses occur during the selected time, the PIR will trigger

the transmitter, sending an alarm signal. A lockout timer prevents the

transmitter from triggering more often than once every 2 minutes

when constant motion is detected. The pulse counting and timing

The unit is supervised for low battery, alarm and status reporting. The

TMD-90 is compatible with any Linear SX format supervised

security receiver. The transmitter sends hourly status reports. A test

Coding switches are not required or used in this transmitter. Each

transmitter is pre-coded at the factory to a unique code. With the SX

remove the case cover. STEP 2 Identify components. Examine the unit to identify

STEP 6 Replace board. Replace the circuit board and

install the adjustment post. Center the detection pattern pointer.

ANTENNA

ADJUSTMENT

WALK TEST

FOUR TYPE "AA"

ADJUSTMENT

REMOVE THE

PROTECTION

DETECTOR

INFRARED

BATTERIES

REPLACE

BATTERY

pattern, the PIR will recognize the change as an intrusion.

format, there are more than sixteen million codes possible.

LED

POST CENTER DETECTION

STRIP

POST

transmitter designed for security applications.

report can be sent by pressing the test button.

options are selected with the OPTION switch.

Remove the battery protection strip.

TRANSMITTER

PATTERN POINTER

ON ADJUSTMENT

USE DURACELL

TOSHIBA LR6G

"AA" ALKALINE

TEST BUTTON

PROTECTION

MN1500 OR

BATTERIES

SWITCH

NOTE:

ONLY!

TAMPER

SWITCH

OPTION

BATTERY

STRIP

POST

STEP 1 Open detector case. Press in the locking tab and

STEP 5 Mount case. Attach the case to the wall using the

screws and screw anchors provided. Mount the detector in a

location where the intruder’s path will likely cross the

LOCKING TAB

OPEN

CASE

FORMAT!

USA & Canada (800) 421-1587 & (800) 392-0123

PUSH IN

SX

ANCHORS TO MOUNT

USE SCREWS AND

(760) 438-7000 • FAX (760) 438-7043

CASE TO WALL

Toll Free FAX (800) 468-1340

SUPERVISED WIRELESS

CASE POINTS

ARROW ON

TO TOP

TMD-90

PASSIVE INFRARED

MOTION DETECTOR

Installation Instructions

detection pattern beams.

7 FEET FROM FLOOR

APPROXIMATELY

Page 2 of the Linear TMD-90 user manual — CURTAIN LENS
Page 2 · click to enlarge
Page 2

Copyright © 2006 Linear LLC 208457 E

STEP 12 Replace and lock cover. Replace the unit’s

CLOSE

INSERT LOCKING

Optional Horizontal Curtain Lens See the figure for

WITH SMOOTH SIDE

3' (.91 m)

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The

Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers

who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant

this product to consumers. Consumers should inquire from their selling dealer as to the nature of the

dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear LLC for

consequential damages arising out of or in connection with use or performance of this product

or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,

installation, or reinstallation. All implied warranties, including implied warranties for merchantability and

implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact

Linear radio controls provide a reliable communications link and fill an important need in portable wireless

1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter

1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating

1 Changes or modifications to the device may void FCC compliance. 1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated

CASE

PRY TABS UP TO

INSERT NEW LENS

REMOVE LENS

SIDE VIEW

40' (12.19 m)

SCREW

BRACKET

Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

Linear LLC Warranty is in lieu of all other warranties express or implied.

OUT

TOP

VIEW

cover and secure it with the locking screw.

signalling. However, there are some limitations which must be observed.

LINEAR LIMITED WARRANTY

frequencies, regardless of code settings.

80' (24.38 m)

power and therefore limited range.

changing supplied lenses.

WILL SNAP SHUT

LOCKING TAB

HORIZONTAL

CURTAIN LENS

to the ultimate users.

STEP 11 Program transmitter into receiver. Refer to the

instructions supplied with the supervised receiver to program the

TMD-90 as a non-restoring PIR sensor. Turn the walk test switch

(#6) OFF. Press the TEST button to cause the unit to send a

signal. The TEST button will not send a valid signal if the unit

TRANSMITTER

Optional Long Range Lens See the figure for

changing supplied lenses. Do not set the pulse count for more

14.43' (4.4 m)

10.5' (3.2 m)

SHIELDINGMetal shielding for maximum RFI/EMI immunity

WITH SMOOTH SIDE

RECEIVER

INSERT NEW LENS

LEARNS

ID CODE

PRY TABS UP TO

131.2' (40 m)

9 main, 8 intermediate, 5 short, 2 creep DETECTION PATTERN: 40 x 40 feet (12.2 x 12.2 M)

SIGNAL PROCESSINGSelectable pulse count (2, 3 & 5 pulses)
RF ENCODINGLinear SX format (A1D PPM @ 200 bps)

REMOVE LENS

DETECTORBalanced dual-element pyro electric
LENSAspheric fresnel lens with 24 facets,

Pulse window (8, 16 & 32 seconds)

DIMENSIONS5.75" high x 3.25" wide x 1.75" deep
VERTICAL ADJUSTInstaller adjustable up and down
POWER REQUIREMENTSFour type “AA” MN1500 batteries

BRACKET

than 2 pulses when using the long range lens.

Operating:12 mA maximum

TAMPER SWITCHSwitch linked to case cover
Standby15 uA maximum
LEDExtra bright for walk test

OUT

MOUNTINGWall, corner or swivel

+32° to +122° F

(0° to +50° C)

SIDE VIEW

6.56' (2 m) 13.12' (4 m) 26.24' (8 m) 52.48' (16 m)

COLORCool Gray 1C

TOP VIEW

NUMBER OF CODES: 16,777,216

is in walk test (switch #6 ON).

OPERATING TEMPERATURE:

SPECIFICATIONS

LONG RANGE LENS

PRESS TEST

SWITCH #6

BUTTON

TO SEND

SIGNAL

MUST BE

OFF

STEP 10 Adjust detection pattern. If the detection

pattern is too high or low, loosen the adjustment post and slide

Optional Swivel Mount An optional swivel mount is

supplied for mounting the TMD-90 to a wall in special situations.

Refer to the figure for details on attaching the swivel mount to the

details on changing lenses. Optional Lens Masks Adhesive stick-on labels are

provided to mask unwanted detection areas of each lens. Apply

POST TO SLIDE

SLIDE BOARD

UP OR DOWN

NOTE: BOARD UP

STICKERS TO THE INSIDE

ADJUSTMENT

PATTERN DOWN

KNOCKOUTS

TO ADJUST

BASE

PUNCH OUT

APPLY LENS MASKING

PATTERN

LOOSEN

ADJUSTS

BOARD

SWIVEL

OF THE LENS

case (swivel mount must be assembled first).

SWIVEL

BASE

BALL

the labels to the inside of the lens.

the circuit board up or down.

SCREW (1)

SCREWS (4)

SHORT

LONG

STEP 9 Walk test. Walk test the unit by walking across the

detection pattern from both sides. The red LED should light as you

cross each detection pattern “finger”. (Alarm transmissions will

STEP 13 System test. Place the receiver into a sensor test

mode. Stay out of the detection pattern of the PIR for at least

4 minutes then walk across the detection pattern. The receiver should indicate that the signal was received.

Optional Vertical Curtain Lens See the figure for

SHOULD BEEP AS ALARM

SYSTEM IN TEST MODE

SIGNAL IS RECEIVED

WITH SMOOTH SIDE

PRY TABS UP TO

INSERT NEW LENS

WALKING ACROSS THE DETECTION PATTERN!

REMOVE LENS

BRACKET

WAIT AT LEAST 4 MINUTES BEFORE

OUT

80' (24.38 m)

SIDE

VIEW

DETECTION PATTERN

4.4' (1.34 m)

WATCH RED LED AS

DETECTOR SENSES

AFTER WAITING, WALK

ACROSS DETECTION

WALK ACROSS

occur in walk test.)

TOP VIEW

40' (12.19 m)

CURTAIN LENS

PATTERN

VERTICAL

MOTION

Show 10 more labels / short text on this page
Tamper Trouble · Power · Low Battery · Supervisory · Alarm · Open · Bypass · # · 7 * · ? ? ?

Ask about the Linear TMD-90

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear TMD-90

Be the first to ask — other owners or our team will answer.

Original document

Linear TMD-90 manual PDF

2 pages·193 KB·Home Security System·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…