EN
Linear logo
Official user manual

Linear Telephone Entry System (AE-100)

24 pages·758 KB·Home Security System·PDF·ENDEFRITNLJA
Linear Telephone Entry System (AE-100)
Table of Contents 80 sections Commercial telephone entry system AE-100 · Guide to the Residence Manager · Contents · Resident register data · … ShowHide
Commercial telephone entry system AE-100p.1Guide to the Residence Managerp.1Contentsp.2Resident register datap.2RESIDENT REGISTER DATA (UP TO 125 RESIDENTS)p.2FOR EACH RESIDENT:p.2DATA FROM INDEPENDENT ACCESS CODES (UP TO 125 CODES)p.2NOTE: EACH INDEPENDENT ACCESS CODE IS REDUCEDp.2OF A UNIT THE NUMBER OF RESIDENTS' ENTRANCESp.2AVAILABLE IN THE DIRECTORYp.2Location of componentsp.3Access to programming from the digital keyboardp.4Programming mode outputp.4TELEPHONE CONNECTIONp.5References for the programme and factory-confi gated default parametersp.6LENGTH OF DIRECTORY NUMBERp.8NPP 02 02#LENGTH#p.8LENGTH = NUMBER (2 OR 3) OF THE DIGITS IN THE DIRECTORY NUMBERp.8FACTORY CONFIGURATION: 3 DIGITSp.8NPP 21 ENTERING A RESIDENT'S DATA IN THE DIRECTORYp.821#REP#NAME#TELEPHONE#CODE#CODEp.8MODIFICATION OF EXISTING RESIDENT DATA IN THE DIRECTORYp.8NPP 22p.822#REP#NAME#TELEPHONE#CODE#p.8ERASING AN EXISTING ENTRY IN THE DIRECTORYp.8NPP 23p.8NPP 31 31#CODE#CODE#p.9ENTERING AN INDEPENDENT ACCESS CODEp.9ERASURE OF AN INDEPENDENT ACCESS CODEp.9NPP 33 33#CODE#CODE#p.9DISPLAY LANGUAGE OF THE SYSTEMp.10NPP 38 38#LANG#p.10FACTORY CONFIGURATION: ENGLISHp.10COUNTING BEFORE LOCKING THE DIGITAL KEYBOARDp.10NPP 51 51#COUNTING#p.10FACTORY CONFIGURATION: 3 TESTSp.10DURATION OF THE ACCESS RELAYp.10NPP 52 52#SECONDS#p.10SECONDS = ACTUATION TIME (04 TO 99 SECONDS)p.10FACTORY CONFIGURATION: 4 SECONDSp.10AUTOMATIC TELEPHONE RESPONSEp.11NPP 61 61#RESPONSE#p.11FACTORY CONFIGURATION: AUTOMATIC RESPONSE ENABLEDp.11CLICKING THE KEYS HEARD IN THE SPEAKERp.11NPP 62 62#CLICK #p.11FACTORY CONFIGURATION: CLICKEDp.11TONE HEARD IN THE SPEAKER AT TIME OF OPERATION OF ACCESS RELAYp.11NPP 63 63#TONALITY#p.11FACTORY CONFIGURATION: TONALITY ACTIVATEDp.11NPP 64p.12MAXIMUM DURATION OF CONVERSATION WITH VISITORSp.1264#DURINGp.12FACTORY CONFIGURATION: 60 SECONDSp.12CONTROL OF THE ACCESS RELAY BY THE RESIDENTp.12NPP 77 77#COMMAND#p.12FACTORY CONFIGURATION: CONTROL BY THE RESIDENT ACTIVATEDp.12NPP 95 95#RECALL#p.12REMINDER BY THE RESIDENTp.12FACTORY CONFIGURATION: THE RESIDENT'S RECALL OPTION IS DISABLEDp.12COPY OF ACCESS DATA ONLY FROM THE MAIN UNIT TO SUBUNITSp.13NPP 30p.1330#SUBUNITS#5#p.13COPY OF ALL DATA FROM THE MAIN UNIT TO SUBUNITSp.13NPP 34p.1334#SUBUNITS#5#p.13TEMPORARY LOCKING OF THE ACCESS RELAYp.14NPP 81 81#p.14ACCESS RELAY LOCKp.14UNLOCKING THE ACCESS RELAYp.14NPP 83 83#p.14NPP 92 92#92#p.14ERASING ALL DIRECTORY ENTRIESp.14ERASURE OF ALL INDEPENDENT ACCESS CODESp.14NPP 93 93#93#p.14Access to the Other Programming Method from the Digital Keyboardp.15Output of the programming mode by other methodp.15Step 2 Enter the new directory numberp.16REMARKS:p.16RESIDENT IN THEp.17DIRECTORYp.17
Page 1 of the Linear Telephone Entry System (AE-100) user manual — Guide to the Residence Manager
Page 1 · click to enlarge
Page 1

Commercial telephone entry system AE-100

Linear Telephone Entry System (AE-100) — Commercial telephone entry system AE-100 diagram (page 1)
Fig. 1 · Commercial telephone entry system AE-100

Guide to the Residence Manager

(760) 438-7000 USA & Canada (800) 421-1587 & (800) 392-0123

Free FAX No. (800) 468-1340

www.linearcorp.com

Page 2 of the Linear Telephone Entry System (AE-100) user manual — Table of Contents
Page 2 · Contents
Contents

Contents

Commercial telephone entry system AE-100p.1Guide to the Residence Managerp.1Contentsp.2Resident register datap.2RESIDENT REGISTER DATA (UP TO 125 RESIDENTS)p.2FOR EACH RESIDENT:p.2DATA FROM INDEPENDENT ACCESS CODES (UP TO 125 CODES)p.2NOTE: EACH INDEPENDENT ACCESS CODE IS REDUCEDp.2OF A UNIT THE NUMBER OF RESIDENTS' ENTRANCESp.2AVAILABLE IN THE DIRECTORYp.2Location of componentsp.3Access to programming from the digital keyboardp.4Programming mode outputp.4TELEPHONE CONNECTIONp.5References for the programme and factory-confi gated default parametersp.6LENGTH OF DIRECTORY NUMBERp.8NPP 02 02#LENGTH#p.8LENGTH = NUMBER (2 OR 3) OF THE DIGITS IN THE DIRECTORY NUMBERp.8FACTORY CONFIGURATION: 3 DIGITSp.8NPP 21 ENTERING A RESIDENT'S DATA IN THE DIRECTORYp.821#REP#NAME#TELEPHONE#CODE#CODEp.8MODIFICATION OF EXISTING RESIDENT DATA IN THE DIRECTORYp.8NPP 22p.822#REP#NAME#TELEPHONE#CODE#p.8ERASING AN EXISTING ENTRY IN THE DIRECTORYp.8NPP 23p.8NPP 31 31#CODE#CODE#p.9ENTERING AN INDEPENDENT ACCESS CODEp.9ERASURE OF AN INDEPENDENT ACCESS CODEp.9NPP 33 33#CODE#CODE#p.9DISPLAY LANGUAGE OF THE SYSTEMp.10NPP 38 38#LANG#p.10FACTORY CONFIGURATION: ENGLISHp.10COUNTING BEFORE LOCKING THE DIGITAL KEYBOARDp.10NPP 51 51#COUNTING#p.10FACTORY CONFIGURATION: 3 TESTSp.10DURATION OF THE ACCESS RELAYp.10NPP 52 52#SECONDS#p.10SECONDS = ACTUATION TIME (04 TO 99 SECONDS)p.10FACTORY CONFIGURATION: 4 SECONDSp.10AUTOMATIC TELEPHONE RESPONSEp.11NPP 61 61#RESPONSE#p.11FACTORY CONFIGURATION: AUTOMATIC RESPONSE ENABLEDp.11CLICKING THE KEYS HEARD IN THE SPEAKERp.11NPP 62 62#CLICK #p.11FACTORY CONFIGURATION: CLICKEDp.11TONE HEARD IN THE SPEAKER AT TIME OF OPERATION OF ACCESS RELAYp.11NPP 63 63#TONALITY#p.11FACTORY CONFIGURATION: TONALITY ACTIVATEDp.11NPP 64p.12MAXIMUM DURATION OF CONVERSATION WITH VISITORSp.1264#DURINGp.12FACTORY CONFIGURATION: 60 SECONDSp.12CONTROL OF THE ACCESS RELAY BY THE RESIDENTp.12NPP 77 77#COMMAND#p.12FACTORY CONFIGURATION: CONTROL BY THE RESIDENT ACTIVATEDp.12NPP 95 95#RECALL#p.12REMINDER BY THE RESIDENTp.12FACTORY CONFIGURATION: THE RESIDENT'S RECALL OPTION IS DISABLEDp.12COPY OF ACCESS DATA ONLY FROM THE MAIN UNIT TO SUBUNITSp.13NPP 30p.1330#SUBUNITS#5#p.13COPY OF ALL DATA FROM THE MAIN UNIT TO SUBUNITSp.13NPP 34p.1334#SUBUNITS#5#p.13TEMPORARY LOCKING OF THE ACCESS RELAYp.14NPP 81 81#p.14ACCESS RELAY LOCKp.14UNLOCKING THE ACCESS RELAYp.14NPP 83 83#p.14NPP 92 92#92#p.14ERASING ALL DIRECTORY ENTRIESp.14ERASURE OF ALL INDEPENDENT ACCESS CODESp.14NPP 93 93#93#p.14Access to the Other Programming Method from the Digital Keyboardp.15Output of the programming mode by other methodp.15Step 2 Enter the new directory numberp.16REMARKS:p.16RESIDENT IN THEp.17DIRECTORYp.17
Page 3 of the Linear Telephone Entry System (AE-100) user manual — Location of components
Page 3 · click to enlarge
Page 3

Location of components

Linear Telephone Entry System (AE-100) — Location of components diagram (page 3)
Fig. 2 · Location of components
Page 4 of the Linear Telephone Entry System (AE-100) user manual — Programming mode output
Page 4 · click to enlarge
Page 4

Programming Access To make life easier for installers familiar with Linear systems and other manufacturers of access control systems, two programming methods are available. The programming position numbers (or function codes) that match those of other equipment help the installer to quickly make changes by typing on different keys they have used to use before.

Linear Telephone Entry System (AE-100) — Access to programming from the digital keyboard diagram (page 4)
Fig. 3 · Access to programming from the digital keyboard

Choice of automatic programming method Programming position numbers (or function codes) change according to the programming method used. See the table on page 6 for numbers used with each method. The keys used to enter programming from the unit's digital keyboard select the programming method that will be used during the current programming session. The programming input by pressing the keys at once & selects the standard programming method (Linear access style). Details of each programming step by standard method are given on pages 8 to 14. The programming input by pressing the keys at once and selecting the Other Programming Method (other style of access by other manufacturers). Details of each programming step by the Other Method are given on pages 15 to 22. Programming from the Digital Keyboard (Standard Method) The system can be programmed using the digital keyboard on the face of the AE-100 housing. The posting indicates the programming information.

Linear Telephone Entry System (AE-100) — Access to programming from the digital keyboard diagram (page 4)
Fig. 4 · Access to programming from the digital keyboard
Linear Telephone Entry System (AE-100) — Access to programming from the digital keyboard diagram (page 4)
Fig. 5 · Access to programming from the digital keyboard

ALPHANUMERIC KEYBOARD INPUT (WHEN PROGRAMMING STEPS REQUIRE TEXT ENTRY)

Access to programming from the digital keyboard

a b c d e f g h i

1. Press & then release the keys at the same time 2. The publication indicates [PASSWORD:] 3. Enter the main password (the factory code is 123456). 4. Press . 5. If the password is correct, posting indicates [ENTER FUNCTION:]. 6. Programming commands can then be entered on the digital keyboard. See the following sections of the manual for details of this step. See also illustrations for alphanumeric characters on the digital keyboard. Voice prompts on the digital keyboard If the program is programmed using a digital keyboard, each of the programming steps consists in entering the program data. With the standard programming method, the system issues sound beeps to indicate whether or not input is correct.

Press the back or erase key

After a correct entry, two short beeps are heard. After incorrect typing, a long beep is heard. When the programming step is completed correctly, three short beeps are heard. Re-entering an order after error If you have an incorrect input, or if it is pressed by mistake on a key during programming, press to reset the digital keyboard and start over step operations.

  • WAIT 3 SECONDS FOR THE NEXT CHARACTER (ONE BEEP SOUNDS AFTER A 3-SECOND BREAK) OR PRESS ANOTHER KEY
  • THE FIRST LETTER OF EACH WORD IS A CAPITAL, AND FOR THE ENTIRE WORD TO BE IN CAPITALS, PRESS THE KEY #
  • COMPLETE THE INPUT BY PRESSING #
  • PRESS THE STAR KEY TO MAKE A BACKWARDS TURN, AGAIN PRESS THE STAR BUTTON TO CLEAR THE LINE

Programming mode output

1. Press:

programming after five minutes of inactivity.

• • •

Page 5 of the Linear Telephone Entry System (AE-100) user manual — TELEPHONE CONNECTION
Page 5 · click to enlarge
Page 5

Phone Programming Most system commands can be programmed on a TouchToneTM phone. The keyboard of the phone behaves like a digital keypad for AE-100s unit. Both methods of programming can be used with a telephone. Telephone connection

TELEPHONE CONNECTION

1. CALL SYSTEM 2. THE SYSTEM RESPONDS TO THE THIRD RINGING 3. THE SYSTEM EMITS SOUNDS INDICATING CURRENT STATE: > A SHORT BEEP ALL RELAYS ARE OPERATED > TWO SHORT BEPS ALL RELAY IS DISABLED > ONE LONG BEEP SOME RELAYS OPEN AND OTHERS CLOSED 4. ENTER THE UNIT NUMBER (1 TO 4) AND PRESS # FOR SINGLE UNIT INSTALLATIONS, PRESS 1# 5. ENTER THE MAIN PASSWORD (DEFAULT PASSWORD: 123456) 6. TO USE THE STANDARD PROGRAMMING METHOD, PRESS [#] TO USE OTHER PROGRAMMING METHOD AND PRESS [*] 7. START PROGRAMMING, ENTER THE STEP NUMBER FOLLOWED BY [#]

1. Call the telephone number of the line to which Unit AE-100 is connected. 2. The AE-100 system responds to the third ringing. 3. Bips are issued by the system to indicate current status of the system (including condition of other units in a multi-unit facility):

A short beep sounds if all the access relays are activated (all doors open). Two short beeps sound if all access relays are disabled (all doors closed). A long beep sounds if there is a combination of activated and deactivated access relays (some doors are open, others closed). 4. Enter the unit number (1 to 4) that you want to connect to and then tap on With a single unit installation, enter the default number 1 assigned to the unit. ✦ NOTES: Connect to main unit No. 1 d

install several units to program the main memory. The main memory can then be copied to each of the other units. 5. Enter the main unit password (the factory programmed code is 123456).

6. To program using the standard programming method,

press To program using the Other Programming Method,

Linear Telephone Entry System (AE-100) — TELEPHONE CONNECTION diagram (page 5)
Fig. 6
VOICE PROMPTS FOR EACH PROGRAMMING METHOD CONDITIONTONES ISSUED BY EMI LATION THE METHOD OF OGRAMMINGANDARD METHOD AFTER INCORRECT ENTRY OFLONG B BIP LONG AFTER CORRECT ENTRY OF AN INTERMEDIATE STEPSHORT NECKX BIPS RTS AFTER CORRECT ENTRY OF A COMPLETE CONTROL COUX BIPS TROI URTS COUS BIPS RTS TR OUTPUT OF THE PROGRAMMING MODE COOIS BIPS AUC URTSUN BIP

If the password is correct, then the system issues two short beeps. 7. You can then enter the programming commands from your phone keyboard. To program the system, see the following pages of the manual.

The steps of the standard programming are shown on pages 8-14. The steps in the Other Programming Method are shown on pages 15 to 22. Voice calls from the phone When programming by telephone, each step of the program consists in entering programming data using the phone keyboard. The system issues beeps via the phone to indicate whether or not entries are correct. Voice prompts that provide feedback during programming are different in each of the programming methods. These differences are shown in the table on the right. Re-entering an order after error If you have an incorrect input, or if the key is pressed by mistake during programming, press and start over. Programming mode output Do not forget to leave the programming mode after completing it.

Linear Telephone Entry System (AE-100) — TELEPHONE CONNECTION diagram (page 5)
Fig. 7

TO EXIT THE PROGRAMMING MODE STANDARD PROGRAMMING METHOD

✦ REMARQUEThe AE-100 system automatically exits from the

programming mode after five minutes of inactivity. To exit the programming mode when using standard method, press: To leave the programming way when using Other Programming Method, tap:

Show 8 more labels / short text on this page
press
Page 6 of the Linear Telephone Entry System (AE-100) user manual — References for the programme and factory-confi gated default parameters
Page 6 · click to enlarge
Page 6

References for the programme and factory-confi gated default parameters

STANDARD PROGRAMMING POSITION NUMBEROTHER VALID FUNCTION CODE NUMBERFUNCTION OF THE PROGRAMMING STAGEFACTORY CONFIGURED DEFAULT PARAMETER 9991OUTPUT FROM PROGRAMMING MODE SYSTEM OPTIONS 3838SYSTEM DISPLAY LANGUAGEENGLISH 5172NUMBER OF INPUT TESTS BEFORE LOCKING THE DIGITAL KEYBOARD3 TESTS 5271DURATION OF ACTIVATION OF THE ACCESS RELAY4 SECONDS 5710WELCOME TEXT DISPLAYEDTELEPHONE ENTRY SYSTEM LINEAR 6174AUTOMATIC TELEPHONE RESPONSEACTIVATED 6275KEYBOARD KEYS CLICKACTIVATED 6376SPEAKER TONE AT THE TIME OF OPERATION OF ACCESS RELAYACTIVATED 6470MAXIMUM CONVERSATION TIME WITH THE VISITOR60 SECONDS 7777CONTROL OF THE RELAY ACCESS BY THE RESIDENTACTIVATED 9595REMINDER BY THE RESIDENTDISABLED COMMAND ACCESS DATA 2101ENTERING AN ENTRY IN THE DIRECTORY FOR A RESIDENT 2202MODIFICATION OF AN ENTRY SAVED IN THE DIRECTORY 2303ERASING AN ENTRY SAVED IN THE DIRECTORY 3131SEIZING AN INDEPENDENT ACCESS CODE 3333ERASURE OF AN INDEPENDENT ACCESS CODE SYSTEM MAINTENANCE 3030COPY OF ACCESS DATA EXCLUSIVELY FROM THE MAIN UNIT TO SUBUNITS 3434COPY OF ALL DATA, FROM THE MAIN UNIT TO SUBUNITS 8005TEMPORARY LOCKING OF THE ACCESS RELAY 8105LOCK OF THE ACCESS RELAY 8305UNLOCKING THE ACCESS RELAY 9204ERASURE OF ALL RESIDENT DATA 9393ERASURE OF ALL INDEPENDENT ACCESS CODES
Linear Telephone Entry System (AE-100) — References for the programme and factory-confi gated default parameters diagram (page 6)
Fig. 8 · References for the programme and factory-confi gated…
Page 7 of the Linear Telephone Entry System (AE-100) user manual — References for the programme and factory-confi gated default parameters
Page 7 · click to enlarge
Page 7
UNIT NOTYPE OF UNITUNIT LOCATION 1MAIN UNIT 2SUBUNIT 3SUBUNIT 4SUBUNIT

Pre-confied unit numbers The company that installed your input system has already programmed this system. If it is a multi-unit installation, subunit numbers have already been given in the subunits and the main unit has also been programmed to recognize these numbers.

Page 8 of the Linear Telephone Entry System (AE-100) user manual — ERASING AN EXISTING ENTRY IN THE DIRECTORY
Page 8 · click to enlarge
Page 8

Resident data programming Up to 125 resident names and telephone numbers can be given. Each resident is assigned one Directory number. The directory number is the number that visitors must enter in order to call the resident. Visitors can also call a resident whose name is displayed by pressing the button . Use the programming fiche provided to organize resident data before entering them into the system. For each of the following steps, enter the main password and enter in the programming mode (if unit is not already there). Exit the programming mode when all programming is complete.

Change in length of directory numbers The factory confi gation of the directory numbers assigns to these three digits. This can be changed into two or three digits.

LENGTH OF DIRECTORY NUMBER

NPP 02 02#LENGTH#

1. Press 2. Enter the length of directory number (2 or 3). 3. Press

LENGTH = NUMBER (2 OR 3) OF THE DIGITS IN THE DIRECTORY NUMBER

FACTORY CONFIGURATION: 3 DIGITS

Entering a resident's data in the directory

1. Press 2. Enter the directory number that will be posted for this resident. 3. Press 的 NOTE: To add the name in capital letters, press before entering the name 4. Enter the name of the resident at affluent price (up to 16 characters). 5. Press 6. Enter the resident's phone number (up to 14 digits). Press

NPP 21 ENTERING A RESIDENT'S DATA IN THE DIRECTORY

21#REP#NAME#TELEPHONE#CODE#CODE

REP = RESIDENT'S DIRECTORY NUMBER NAME = RESIDENT NAME (UP TO 16 CHARACTERS) PHONE = RESIDENT TELEPHONE NUMBER (UPTO 14 DIGITS) CODE = RESIDENT ACCESS CODE (4 DIGITS) CODE = NEW ENTRY OF THE CHECK ACCESS CODE

keys, , or hold them down to record 1-4 breaks of two seconds. Hold the key down for about two seconds. NOTES: Each pause entered counts as one of the 14 digits allowed for telephone number. 7. Press 8. Enter a access code single four-digit for this resident. 9. Press 10. Enter the access code Single four-digit check. 11. Press

Changes to existing resident data in the directory Once an entry has been entered into the register, it can be changed to change the name, telephone number or access code of the resident.

MODIFICATION OF EXISTING RESIDENT DATA IN THE DIRECTORY

NPP 22

✦ NOTES: This step cannot be done remotely by telephone. 1. Press 2. Enter the Directory number the resident. 3. Press NOTES: To change the name using capital letters,

22#REP#NAME#TELEPHONE#CODE#

REP = RESIDENT'S DIRECTORY NUMBER NAME = RESIDENT NAME (UP TO 16 CHARACTERS) PHONE NUMBER = RESIDENT TELEPHONE NUMBER (UPTO 14 DIGITS) CODE = RESIDENT ACCESS CODE (4 DIGITS)

Press before entering the name. 4. Change the name the resident has a good deal (up to 16 characters), and apppuy on the key, or to keep the same name, press . 5. Change the telephone number The resident (up to 14 digits, see above how to enter breaks and press , or to keep the same phone number, tap . 6. Change the access code If you want to keep the same access code, simply press . Clearing an existing entry in the directory The entries of the directory can be deleted individually (to delete all entries from the directory, see the programming step 92).

ERASING AN EXISTING ENTRY IN THE DIRECTORY

NPP 23

1. Press 2. Enter the directory number. 3. Press 4. Enter the directory number again. 5. Press

23#REP#REP #REP= RESIDENT'S DIRECTORY NUMBER REP= RESIDENT RE-ENTERED REGISTER NUMBER FOR VERIFICATION

Page 9 of the Linear Telephone Entry System (AE-100) user manual — ERASURE OF AN INDEPENDENT ACCESS CODE
Page 9 · click to enlarge
Page 9

Programming an independent access code One independent access code is a number entered by the digital keyboard of unit AE-100 to request entry. Up to 125 independent four-digit access codes can be programmed.

✦ REMARQUEEach independent access code programmed

reduces by one unit the number of possible entries in the directory. Use the programming fiche provided to organize independent access codes before entering them into the system. For each of the following steps, enter the main password and enter in the programming mode (if unit is not already there). Exit the programming mode when it is complete.

Seizure of an independent access code Independent access codes must be entered separately.

NPP 31 31#CODE#CODE#

ENTERING AN INDEPENDENT ACCESS CODE

1. Press 2. Enter the new independent access code. 3. Press 4. Enter the independent access code again for verification. 5. Press

CODE = NEW INDEPENDENT ACCESS CODE CODE = RE-ENTERING THE INDEPENDENT ACCESS CODE FOR VERIFICATION

Clearing an Independent Access Code Independent access codes can be entered separately. (to delete all independent access codes, see Programming Step 93).

ERASURE OF AN INDEPENDENT ACCESS CODE

NPP 33 33#CODE#CODE#

1. Press 2. Enter the independent access code to erase. 3. Press 4. Enter the independent access code again to erase. 5. Press

CODE = INDEPENDENT ACCESS CODE TO BE DELETED CODE = NEW ENTRY OF THE INDEPENDENT ACCESS CODE FOR VERIFICATION

Page 10 of the Linear Telephone Entry System (AE-100) user manual — SECONDS = ACTUATION TIME (04 TO 99 SECONDS)
Page 10 · click to enlarge
Page 10

System Options Factory configurations will be appropriate in most cases. To customize the system, access the programming mode by phone or via the digital keyboard. Use the programming fiche provided to record all changes made to system options before entering them into the system. For each of the following steps, enter the main password and enter in the programming mode (if unit is not already there). Exit the programming mode when it is complete.

System Display Language The system's default language is English. Three other languages may be chosen as the user language and for programming features.

DISPLAY LANGUAGE OF THE SYSTEM

NPP 38 38#LANG#

✦ REMARQUEThis step cannot be accomplished remotely by

LANG = SYSTEM DISPLAY LANGUAGE 1 = ENGLISH 2 = SPANISH 3 = FRENCH 4 = PORTUGUESE

Phone.The system supports the posting of a single

language at once. 1. Press 2. Choose a language: Enter 1 for English Enter 2 for Spanish Enter 3 for French Enter 4 for Portuguese 3. Press Count before locking the digital keyboard The system counts the number of invalid access codes entered by the numeric keypad. If the number of input tests exceeds the fi xed number for locking, the digital keyboard is locked for 90 seconds. The factory confi gation for this number of tests is three. The possible value is one to nine.

FACTORY CONFIGURATION: ENGLISH

COUNTING BEFORE LOCKING THE DIGITAL KEYBOARD

NPP 51 51#COUNTING#

1. Press 2. Enter the number of input tests before locking on keyboard (1 to 9). 3. Press

COUNT = NUMBER (1 TO 9) OF INCORRECT INPUT TESTS THAT CAUSE THE LOCK FOR 90 SECONDS

FACTORY CONFIGURATION: 3 TESTS

The time to actuate the access relay The factory confi gation causes the relay to operate for four seconds. The operating time can be adjusted between 4 and 99 seconds to suit different types of input control devices.

DURATION OF THE ACCESS RELAY

NPP 52 52#SECONDS#

1. Press 2. Enter the time (in seconds) during which the access relay remains activated (04 to 99). 3. Press

SECONDS = ACTUATION TIME (04 TO 99 SECONDS)

FACTORY CONFIGURATION: 4 SECONDS

Page 11 of the Linear Telephone Entry System (AE-100) user manual — FACTORY CONFIGURATION: TONALITY ACTIVATED
Page 11 · click to enlarge
Page 11

System Options (continued) Text of the host message displayed L'Unité AE-100 has a visitor reception message alternating with instructions to find and call a resident. The home message can be customized according to the installation.

Linear Telephone Entry System (AE-100) — AUTOMATIC TELEPHONE RESPONSE diagram (page 11)
Fig. 9
✦ REMARQUEThis step cannot be accomplished remotely by

Phone. 1. Press ✦ NOTES: To enter only letters of printing, press

LINE 1 = UP TO 16 CHARACTERS LINE 2 = UPTO 16 CHARACTERS

first on: before entering the text.

2. Type the new text for the top line of posting (up to 16 characters). 3. Press

first on: before entering the text. 4. Type the new text for the lower line of display (up to 16 characters). 5. Pressing Automatic Telephone Response The factory confi gation allows the system to detect a ringtone on the telephone line and respond to the call.

AUTOMATIC TELEPHONE RESPONSE

NPP 61 61#RESPONSE#

✦ REMARQUEThe response functionality to a telephone call can

be disabled, but in this case remote programming functions, resident remote control and residents recall are also deactivated. 1. Press 2. Choose the automatic phone response option: Enter 0 to DISACTAIN the autophone answer. Enter 1 for ACTIVER the automatic phone response. 3. Press Clicking the Keys heard in the speaker The factory config allows you to hear the key clicks in the loudspeaker whenever it is pressed on a button of the digital keyboard. This feature can be disabled.

RESPONSE = 0 TO DISABLE THE ANSWER CALL RESPONSE = 1 TO ACTIVATE THE REPLY TO THE CALL

FACTORY CONFIGURATION: AUTOMATIC RESPONSE ENABLED

CLICKING THE KEYS HEARD IN THE SPEAKER

NPP 62 62#CLICK #

1. Press 2. Choose the key click agreement option: Enter 0 to DISACTIVER the keys click. Enter 1 for ACTIVER the key click. 3. Press

CLICK = 0 TO DISABLE THE RATCHETING OF KEYS CLICK = 1 TO ACTIVATE THE RATTLING OF KEYS

FACTORY CONFIGURATION: CLICKED

Tonality heard in the speaker when operating the access relay The factory confederation causes a tone to be heard in a loudspeaker for two seconds when running the access relay. It is possible to disable this tone.

TONE HEARD IN THE SPEAKER AT TIME OF OPERATION OF ACCESS RELAY

NPP 63 63#TONALITY#

1. Press 2. Choose the agreement option of a tone in the speaker: Enter 0 to DISACTAIN the tone in your speaker. Enter 1 for ACTIVER the tone in the speaker. 3. Press

TONE = 0 TO DISABLE THE TONE OF THE SPEAKER TONES = 1 TO ACTIVATE THE VOICE OF THE LOUDSPEAKER

FACTORY CONFIGURATION: TONALITY ACTIVATED

Page 12 of the Linear Telephone Entry System (AE-100) user manual — FACTORY CONFIGURATION: THE RESIDENT'S RECALL OPTION IS DISABLED
Page 12 · click to enlarge
Page 12

System Options (continued) Maximum time for conversation with visitors Visitors can speak on the phone to the resident until he or she grants or refuses entry into the residence. If the resident responds to a visitor's request by pressing the phone key, the system hangs up and releases the telephone line. If for some reason the resident does not press or hang up on the phone key, then the system will cut the line to the visitor after 60 seconds. Ten seconds and then five seconds before hanging up, a tone is heard on the phone line to remind the resident of the imminent cut. The resident can extend the conversation by pressing the # button on his/her phone. The duration before disconnection can be set between 10 and 180 seconds.

NPP 64

MAXIMUM DURATION OF CONVERSATION WITH VISITORS

64#DURING

DURATION = TIME TO AUTOMATIC CONVERSATION SHUTDOWN (010-180 SECONDS)

FACTORY CONFIGURATION: 60 SECONDS

1. Press 2. Enter the conversation duration in seconds (010 to 180). 3. Press the Relay Control by the Resident The factory confi gation allows the resident to activate the access relay by pressing key 9 of his phone when he receives a call from unit AE-100. This function can be disabled. When this function is disabled, the input can only be granted by using the resident's access code and independent access codes entered on the unit's digital keyboard.

CONTROL OF THE ACCESS RELAY BY THE RESIDENT

NPP 77 77#COMMAND#

COMMAND = 0 TO DISABLE THE ORDER BY RESIDENT COMMAND = 1 TO ACTIVATE THE ORDER FROM RESIDENT

1. Press 2. Choose the option of commanding the access relay by the resident: Enter 0 to DISACTIVER the control of the access relay by the residents. Enter 1 for ACTIVER the control of the access relay by the resident. 3. Press Reminder by Resident The callback function by the resident allows AE-100 to answer the phone and switch into speaker mode if the telephone is dialed within 60 seconds of last use of the AE 100 unit. This function gives residents who have missed a visitor's recent call the opportunity to recall the latter. This function can only be used on single unit installations. The factory confi gation disables the recall function by the resident. But this function can be activated.

FACTORY CONFIGURATION: CONTROL BY THE RESIDENT ACTIVATED

NPP 95 95#RECALL#

REMINDER BY THE RESIDENT

REMINDER = 0 TO DISABLE THE RECALL BY RESIDENT RECALLS = 1 TO ACTIVATE THE CALLBACK BY RESIDENT

FACTORY CONFIGURATION: THE RESIDENT'S RECALL OPTION IS DISABLED

✦ REMARQUESo that the reminder function by the resident can

be enabled, the automatic telephone response function NPP #61 must also be activated.

1. Press 2. Select the recall option by resident: Enter 0 for DISACTIVER the reminder option by the resident. Enter 1 for ACTIVER the recall option by the resident. 3. Press

Page 13 of the Linear Telephone Entry System (AE-100) user manual — COPY OF ALL DATA FROM THE MAIN UNIT TO SUBUNITS
Page 13 · click to enlarge
Page 13

System utility controls Several utilities commands are available for the system. These commands can be used to copy data from other units of a multi-unit system, erase memory, provide information about the system and control relays. For each of these steps, enter the main password and enter in the programming mode (if unit is not already there). Exit the programming mode when it is complete. Copying data only from the main unit to subunits To synchronize programming in multi-unit installations, directory numbers and access codes can be copied from the primary unit to selected subunit.

COPY OF ACCESS DATA ONLY FROM THE MAIN UNIT TO SUBUNITS

NPP 30

30#SUBUNITS#5#

✦ REMARQUEIn order for this control to work, the system must be

The first is for installation to several units. ✦ NOTES: This utility command can only work from

SUBUNITS = NUMBER OF EACH SUBUNIT (2 TO 4) TO WHICH ACCESS DATA IS COPIED IN A MULTI-UNIT SYSTEM

Main unit.

access data which existed in the selected subunits. 1. Press 2. Enter the unit number(s) of all subunits that must receive access data. Examples:

To copy to Unit Two, enter only To copy into Unit Three, type Only To copy towards Units Two and Three, enter To copy back to Units Two, Three and Four, enter 3. To execute the command, enter or input to exit (any other input will cancel the order).

Copying all data from the main unit to subunits To synchronize programming in multi-unit facilities, all system data can be copied from the primary unit to selected subunit. This includes directory numbers, independent access codes and all system options except the subunit number).

COPY OF ALL DATA FROM THE MAIN UNIT TO SUBUNITS

NPP 34

34#SUBUNITS#5#

✦ REMARQUEIn order for this control to work, the system must be

SUBUNITS = NUMBER OF EACH SUBUNIT (2 TO 4) TO WHICH THE DATA SET IS COPIED IN A MULTI-UNIT SYSTEM

The first is for installation to several units. ✦ NOTES: This utility command can only work from

Main unit. ATTENTIONThis utility command erases and replaces ALL the

data which existed in the selected subunits. 1. Press 2. Enter the unit number(s) of all subunits that must receive all data. Examples:

To copy to Unit Two, enter only To copy into Unit Three, type Only To copy towards Units Two and Three, enter To copy back to Units Two, Three and Four, enter 3. To execute the command, enter or input to exit (any other input will cancel the order).

Page 14 of the Linear Telephone Entry System (AE-100) user manual — ERASURE OF ALL INDEPENDENT ACCESS CODES
Page 14 · click to enlarge
Page 14

System utility controls (cont'd) Temporary locking of the access relay For maintenance or testing, while the unit is in programming mode it is possible to manually lock the access relay from the digital keyboard for a few hours.

NPP 80 80#HOURS#HRS = TEMPORARY LOCKING OF THE ACCESS RELAY IN HOURS (01 TO 98)

TEMPORARY LOCKING OF THE ACCESS RELAY

1. Press 2. Enter the lock time of access relay in hours (01 to 98). 3. Pressing the Access Relay Lock For maintenance or testing, and while the unit is in the programming mode it is possible to lock the access relay manually from the digital keyboard for an unfailing time.

NPP 81 81#

ACCESS RELAY LOCK

✦ REMARQUEThis command resets the relay and cancels the duration

temporary locking provided by the NPP 80. 1. Press Unlocking the access relay For maintenance or testing, and while the unit is in the programming mode it is possible to unlock the access relay when manually locked from the digital keyboard (temporarily or unsurely).

UNLOCKING THE ACCESS RELAY

NPP 83 83#

1. Press

Clearing all entries in the directory This utility command permanently erases any resident's directory numbers, names, phone numbers and access codes.

NPP 92 92#92#

ERASING ALL DIRECTORY ENTRIES

in the unit.This step cannot be accomplished remotely by

Phone. 1. Press 2. Press again to check cation. Clearing all Independent Access Codes This utility command permanently erases any independent access codes.

ERASURE OF ALL INDEPENDENT ACCESS CODES

NPP 93 93#93#

in the unit.This step cannot be accomplished remotely by

Phone. 1. Press 2. Press again to check cation.

Page 15 of the Linear Telephone Entry System (AE-100) user manual — Output of the programming mode by other method
Page 15 · click to enlarge
Page 15

Section on Alternative Programming Method To make life easier for installers familiar with Linear and other manufacturers' access control systems, two programming methods are available. Function codes adapted to other equipment help the installer quickly make programming changes using keyboard keys that they already know.

Linear Telephone Entry System (AE-100) — Access to the Other Programming Method from the Digital Keyboard diagram (page 15)
Fig. 10 · Access to the Other Programming Method from the Digi…

Selection of the Other Programming Method The program position numbers (or function codes) change according to the programming method used. See the table on page 6 for numbers used by each of the programming methods. The keys used to enter programming from the unit's digital keyboard select the programming method used for the current programming session. Entering the programming mode by pressing at the same time on keys & selects the Other Programming Method (other access style used by other manufacturers). Details of each of the programming stages using the Other Method are shown on pages 15 to 22. Voice Invites with the Other Method Voice prompts that provide feedback during programming by the unit's digital keyboard or on the phone are different with the Other Programming Method. These differences are shown in the table on the right.

Linear Telephone Entry System (AE-100) — Access to the Other Programming Method from the Digital Keyboard diagram (page 15)
Fig. 11 · Access to the Other Programming Method from the Digi…

AFTER INCORRECT ENTRY TWO LONG BEEPS A LONG BEIP

AFTER CORRECT ENTRY OF AN INTERMEDIATE STEP A SHORT BEEP TWO SHORT BEPS

AFTER CORRECT ENTRY OF A COMPLETE COMMAND TWO SHORT BEEPS THREE SHORT BEPS

OUTPUT PROGRAMMING MODE THREE SHORT BEEPS NO BEEP

Alphanumeric input into the Other Method When using the digital keyboard for alphanumeric data input in the Other Programming Method, each key captures the data differently than that of the standard interface mode. See the illustration of the digital keyboard on the right.

Access to the Other Programming Method from the Digital Keyboard

Linear Telephone Entry System (AE-100) — Access to the Other Programming Method from the Digital Keyboard diagram (page 15)
Fig. 12 · Access to the Other Programming Method from the Digi…

1. Press & and then release the keys. 2. The publication indicates [MAIN CODE:] 3. Enter the main code (the factory confi gation is 123456). 4. The display generates asterisks as one enters the code. 5. If the main code is incorrect, the system emits two long beeps and returns to normal operating mode. 6. If the password is correct, posting indicates [CHOOSE FUNCTION:] 7. The commands can then be entered on the digital keyboard. See the following pages of the manual for details on steps in the Other Programming Method. Re-entering an order after error If you are entering an incorrect input, or if you press a wrong key during programming, tap to reset the keyboard and start over the program step.

ALPHANUMERIC INPUT BY KEYBOARD FOR THE INTERFACE OF THE OTHER PROGRAMMING METHOD (WHEN PROGRAMMING STEPS REQUIRE TEXT ENTRY)

Q Z - , . ' * q z 0 1 2 3 4 5 6 7 8 9

A B C a b c D E F d e f

Output of the programming mode by other method

1. Press:

programming after five minutes of inactivity.

  • PRESS: [#] AFTER EACH LETTER TO ENTER THE FOLLOWING CHARACTER
  • FINISH A COMPLETE ENTRY BY PRESSING [#] [#].
  • PRESS: [8] AND THEN [0] TO GO BACK TO A CHARACTER
  • PRESS: [*] TO ERASE THE ENTIRE ENTRY
Page 16 of the Linear Telephone Entry System (AE-100) user manual — REMARKS:
Page 16 · click to enlarge
Page 16

References to the Other Programming Method See the following pages for further programming methods. For each of the following steps, enter the main password and enter in the programming mode (if unit is not already there). Exit the programming mode when it is finished.

FUNCTION CODE LOCAL PROGRAMMING BY TELEPHONE 01 DATA PROGRAMMING OF A NEW RESIDENT

Step 1 Enter function code 01 and press

#, a short beep sounds.

Step 2 Enter the new directory number

(two or three digits) and press #, a short beep sounds. (If you hear two long beeps, it's because the directory number already exists, go back to I-Step 1.)

Step 2 Enter the Directory number Two or three

Four different fields must be programmed: directory number, name, telephone number and access code.

Directory number: A unique two or three digit identification number is assigned to each resident.

Step 3

Step 3 Enter the name of the resident (up to 16

If the directory number has already been used, posting indicates:

characters) and press # after each character, then again on # after the last character, a short beep sounds.

Name: up to 16 characters.

Telephone numberup to 14 digits

Step 4 Enter the telephone number (up to

Return to Step 2.

Access code: four-digit code assigned to the resident for entry using digital keyboard

14 digits), press # after each number, then again on # after the last issue, a short beep sounds.

If the memory is full, posting indicates:

Step 5 Enter access code, then press #,

REMARKS:

Two short beeps are ringing.

1. Directory numbers can be given with two or three digits. All these numbers must have the same number of digits.

Return to Step 2.

Step 3 Enter name the resident (up to 16 characters),

Press # after each character, then again on # after the last character

2. A directory number cannot be duplicated.

3. Each directory number represents a resident.

Step 4 Enter the telephone number of the resident

4. Clear unused directory numbers to prevent the system from running out of memory.

(up to 14 digits), press # after each number, then again on # after the last number. Press the 1, 2, 3 or 4 keys and hold them down for about two seconds to record 1-4 breaks of 2 seconds. NOTES: Each pause entered counts as one of the 14 digits allowed for telephone number.

5. Resident names may be entered in any order. The system provides them in alphabetical order.
6. The same name, telephone number and access code may exist under different directory numbers.

Step 5 Enter the access code four digits,

Step 6 Press #.

numbers

Page 17 of the Linear Telephone Entry System (AE-100) user manual — NOT AVAILABLE
Page 17 · click to enlarge
Page 17

FUNCTION CODE LOCAL PROGRAMMING BY PHONE 02 CHANGE DATA FROM

RESIDENT IN THE

Step 2 Enter the new Directory number Two or three

figures.

DIRECTORY

Select a directory number to be modified (you need the resident's register number in order to change it).

The name the current resident is:

Step 3 To keep this name, press # and move to Step 5. Step 4 To change the name, press and then grab a

new name (up to 16 characters), press # after each character, then again on # after the last character:

NOT AVAILABLE

Step 5 To keep this phone number, press #

and proceed to step 7.

Step 6 To change the telephone number, press

then enter a new phone number (up to 14 digits), press # after each number, and again tap # after the last number. Press the 1, 2, 3 or 4 keys and hold them down for about two seconds to record 1-4 breaks of 2 seconds. NOTES: Each pause entered counts as one of the 14 digits allowed for telephone number.

Step 7 To keep the access code, press #. Step 8 To change the access codeenter a new code

d

03 ERASE DATA FROM A

Step 1 Enter function code 03 and press

#, a short beep sounds.

Step 2 Enter the directory number (two or

RESIDENT IN THE

Step 2 Enter the Directory number Two or three digits

three digits) to erase and press #, two short beeps sound. (If a long beep followed by two short beeps is heard, the directory number did not exist, return to Step 1.)

to erase, then press #:

DIRECTORY This erases a single entry in the directory. This command releases the memory occupied by an unused directory entry.

If the directory number does not exist, posting indicates an error, return to Step #1.

04 CLEAR ALL

DATA OF RESIDENTS IN THE

Step 2 Enter the number and press #.

DIRECTORY This erases all entries in the directory. This command erases all directory numbers, names, phone numbers and access codes related to the directory.

NOT AVAILABLE

Step 3 Enter 5 for cation check, then press # (or press

on

Page 18 of the Linear Telephone Entry System (AE-100) user manual — NOTES:
Page 18 · click to enlarge
Page 18

FUNCTION CODE LOCAL PROGRAMMING BY PHONE 05 MANUAL CONTROL OF THE ACCESS RELAY

Step 1 Enter function code 05 and press #, a short beep sounds.

" "

Step 2 Enter the number of hours from 01 to 98, to activate the access relay and then press #. - OU - Enter the number 99 to activate the unsatisfied access relay and then press #. - OU - Enter the number 00 to disable the access relay, then press #. Two long beeps and two short beep sounds.

Step 2 Enter the number of hours from 01 to 98 during which

the access relay will be activated, then press #. - OU - Enter the number 99 to activate the unsatisfied access relay and then press #. - OU - Enter the number 00 to disable the access relay, then press #. - OU - Enter

This command can be used to lock the access relay unsuspected or temporarily, and to unlock the access relay.

06 NUMBER OF DIGITS

NUMBERS OF

Step 2 The display indicates the current value. Type 2 or 3, then press #.

DIRECTORY Choose two or three digits for the length of the directory number (the default factory config is three digits). NOTES: In multi-unit installations, if sub-units are updated with access data containing directory numbers that have more digits than those with which the unit is confided, then the number of digit(s) for the sub-group's directory numbers will be automatically adjusted.

- OU - Enter

NOT AVAILABLE

10 HOME TEXT

# $

DISPLAYED

Step 2 Enter the new home message. There is

The AE-100 poster generates a message of welcome to visitors alternating with instructions for finding and calling a resident. The home message can be customized according to the installation.

32 characters to do this. The display progresses until the beginning of the lower line after the 16th character entered on the upper line. Type # after each new character, type ## after the last character.

NOT AVAILABLE

30 COPIES OF DATA

Step 1 Enter function code 30 and press

#, a short beep sounds.

ACCESS TO THE UNIT

Step 2 Enter the numbers of all sub-

MAIN TO SUBUNITS

Step 2 Enter the unit numbers (2, 3 and 4) of all

Units (2, 3 and 4) to which the data must be copied, then press #, a short beep sounds.

subunits to copy the data to them, then press #.

To synchronize programming in the multiunit facilities, it is possible to copy directory entries and access codes independent of the main unit to selected subunits.

Step 3 Enter 5 for verification, then press

#, two short beeps are ringing. (Any entry other than 5# cancels the order.)

Step 3 Enter 5 for the cation check, then press #.

NOTES:

- OU -

To allow network communications in multi-unit systems, when running this remote over the phone, the system disconnects your call after step 3 and then copies data from the main unit to sub-units.

Enter

NOTES:

In order for this control to work, the system must be previously confided for installation with several units.

Page 19 of the Linear Telephone Entry System (AE-100) user manual — NOT AVAILABLE
Page 19 · click to enlarge
Page 19

LOCAL PROGRAMMING FUNCTION CODE BY TELEPHONE 31 ACCESS CODES ENTERED

Step 1 Enter function code 31 and press #, a short beep sounds.

Step 2 Enter the new independent four-digit access code, press #, a short beep sounds.

INDEPENDENT

Step 2 Enter the new independent access code to

An independent access code is a digit entered by the AE-100 digital keyboard to request entry into the residence. Up to 125 independent access codes can be set up with four digits.

four digits, then press #.

Step 3 Enter the new independent four-digit access code a second time to check for cation.

Step 4 Press #, two short beeps are ringing.

Step 3 Enter the new independent access code to

four digits a second time to check the cation.

Step 4 Press #.

33 ERASURE OF A

Step 1 Enter function code 33 and press #, a short beep sounds.

Step 2 Enter the independent four-digit access code to erase, press #, a short beep sounds.

ACCESS CODE

INDEPENDENT

Step 2 Enter the new independent access code to

This command erases a single independent access code.

four digits, then press #.

Step 3 Enter the independent four-digit access code a second time to delete, for verification.

Step 3 Enter the new independent access code to

Step 4 Press #, two short beeps are ringing.

four digits a second time to check the cation.

Step 4 Press #.

Step 1 Enter function code 34 and press #, a short beep sounds.

34 COPY ALL MAIN MEMORY

Step 2 Enter the numbers of all subunits (2, 3 and 4) to which you wish to copy data, then press #, a short beep sounds.

VERS LES SOUS-

UNITS To synchronize the program- tion in multiunit facilities, it is possible to copy all data from the main unit to selected sub-units. This includes directory entries, independent access codes and all system options confi gations (except subunit numbers). NOTES: This utility command can only be executed from the main unit.

Step 2 Enter the numbers of all subunits (2,

3 and 4) to which you want to copy the data, then press #.

Step 3 Enter 5 to check cation, then press #, two short beeps ring. (Any entry other than 5# will cancel this order.)

NOTES:

To allow network communications in multi-unit systems, when running this remote over the phone, the system disconnects your call after step 3 and then copies data from the main unit to sub-units.

Step 3 Enter 5 for verification, then press #.

- OU -

Enter

NOTES:

In order for this control to work, the system must be previously confided for installation with several units.

38 LANGUAGE OF THE DISPLAY

#

SYSTEM The default factory confi gation of the language is English. Three other languages can be chosen as the user language and the programming display language. NOTE: The system supports the posting of one language at a time.

Step 2 Enter: 1 for English (default language) 2 for Spanish 3 for French 4 for Portuguese Step 3 Press #.

NOT AVAILABLE

Page 20 of the Linear Telephone Entry System (AE-100) user manual — LOCKING OF THE
Page 20 · click to enlarge
Page 20

FUNCTION CODE LOCAL PROGRAMMING BY TELEPHONE 70 MAXIMUM CONVERSATION TIME WITH THE

Step 1 Enter function code 70 and press #,

A short beep sounds.

" &

Step 2 Enter the new conversation time (010)

At 180 seconds) and press #, two short beeps sound.

Step 2 The posting indicates the conversation time currently

VISITORS

confi gure.Enter the new conversation duration (010 to 180 seconds).

If for some reason the resident does not press or hang up on the phone key, then the system will cut the line to the visitor after 60 seconds. Ten seconds and then five seconds before hanging up, a tone is heard on the phone line to remind the resident of the imminent cut. The resident can extend the conversation by pressing the # button on his/her phone. The duration before disconnection can be set between 10 and 180 seconds.

Step 3 Press #, two short beeps are ringing.

Step 3 Press #.

71 DURATION OF OPERATION

Step 1 Enter function code 71 and press #,

A short beep sounds.

Step 2 Enter the new relay operation time

(04 to 99 seconds).

RELAY

Step 2 The display indicates the current operating time

The factory confederation allows the access relay to be operated for four seconds. The activation time can be set from 4 to 99 seconds for the various types of access control devices.

The system access relay. Enter the new time to activate the access relay (04-99 seconds).

Step 3 Press #, two short beeps are ringing.

Step 3 Press #.

72 NUMBER OF INLET TESTS BEFORE THE

Step 1 Enter function code 72 and press #,

A short beep sounds.

$ #

Step 2 Enter the new number of entry tests

The test results are shown in Table 1.

LOCKING OF THE

KEYBOARD The system counts the number of input tests by entering invalid access codes on the digital keyboard. If the number of tests exceeds the system-tolerated test, the keyboard shall be locked for 90 seconds. The factory default config for the number of tests before keyboard lock is three. The value of the number of tests possible may be one to nine.

Step 2 The display indicates the number of inlet tests

Step 3 Press #, two short beeps are ringing.

before the keyboard is locked. Enter the new number of tests to be tolerated (1-9 trials).

Step 3 Press #.

Page 21 of the Linear Telephone Entry System (AE-100) user manual — NOT AVAILABLE
Page 21 · click to enlarge
Page 21

FUNCTION CODE LOCAL PROGRAMMING TELEPHONE PROGRAMMING 74 PHONE RESPONSE

' (

AUTOMATIC The factory confederation allows the system to detect a tone signal on the telephone line and respond to the call.

Step 2 The display indicates the response setting

automatic.

Enter 0 to disable the automatic response.

NOT AVAILABLE

Enter 1 to enable automatic response (default setting).

Step 3 Press #.

75

Step 1 Enter function code 75 and press

#, a short beep sounds.

$ ( (

KEYBOARD KEYS IN THE

Step 2 Enter 0 to disable the clicks of

Keyboard keys.

SPEAKER The factory confederation allows the speaker to make clicks of keys sound when pressing on the digital keyboard. This function can be disabled.

Step 2 Enter 0 to disable the click of the keys on

Enter 1 to activate the key-clicking button.

keyboard.

Enter 1 to enable the keyboard keys click (default setting).

Step 3 Press #, two short beeps

sound.

Step 3 Press #.

76 TONES

Step 1 Enter function code 76 and support

On #, a short beep sounds.

$ # ) "

MOMENT OF OPERATION OF THE

Step 2 Enter 0 to disable the relay tone.

Enter 1 to activate the relay tone.

ACCESS RELAYS The factory confederation causes the transmission of a tone transmitted by the loudspeaker for two seconds when the access relay is activated. This function can be disabled.

Step 2 Enter 0 to disable the relay tone.

Step 3 Press #, two short beeps

Enter 1 to activate the relay tone (default setting).

sound.

Step 3 Press #.

77 CONTROL OF THE RELAY ACCESS BY

( ( "

RESIDENTS The factory confederation allows residents to activate the access relay by pressing key 9 of their phone when they receive a call from Unit AE-100. This function can be disabled. If it is, then entry is only possible for them by entering their resident access code and independent access codes on the unit's digital keyboard.

Step 2 Enter 0 to disable relay control

access by the resident.

Enter 1 to enable the resident's access relay command (default setting).

NOT AVAILABLE

Step 3 Press #.

Page 22 of the Linear Telephone Entry System (AE-100) user manual — RESIDENT
Page 22 · click to enlarge
Page 22

FUNCTION CODE LOCAL PROGRAMMING BY TELEPHONE 91 OUTPUT OF MODE

Step 1 To exit the programming mode, enter

Step 1 To get out of the programming mode,

function code 91, then press #.

enter function code 91.

PROGRAMMING

NOTES:

Step 2 Press #, three short beeps

The number of this command is entered and the unit is removed from the programming mode and returned to normal operating mode.

The AE-100 system automatically exits the programming mode after five minutes of inactivity.

sound.

93 ERASURE

OF ALL ACCESS CODES

Step 2 Enter function code 93 again for

INDEPENDENT

Check cation, then press #. NOT AVAILABLE

This utility command permanently erases all independent access codes.

95 REMINDER BY THE

Step 1 Enter function code 95 and press

#, a short beep sounds.

(

RESIDENT

Step 2 Enter 0 to disable the function of

The resident's callback function allows the AE-100 system to answer the phone and switch into speaker mode if the telephone calls occur within 60 seconds of most recent use of the Ae-100. This function gives residents the opportunity to call a visitor if they have just missed a call. The factory confi gation disables this function but it can be activated.

recall by the resident.

Step 2 The display indicates the current confi gation.

Enter 1 to enable the reminder function by the resident.

Enter 0 to disable the reminder function by the resident (default setting).

Step 3 Press #, two short beeps

Enter 1 to enable the reminder function by the resident.

sound.

Step 3 Press #.

Page 23 of the Linear Telephone Entry System (AE-100) user manual — System Instructions AE-100 Request for visitor to enter by call
Page 23 · click to enlarge
Page 23

System Instructions AE-100 Request for visitor to enter by call

Linear Telephone Entry System (AE-100) — System Instructions AE-100 Request for visitor to enter by call diagram (page 23)
Fig. 13 · System Instructions AE-100 Request for visitor to en…

If the visitor already knows the resident's directory number, first press the key and then enter the directory number to call the resident. If the visitor does not know the resident's directory number, he can challenge entries in the directory that appear alphabetically by pressing or . Press the directory from A to Z. Press defi late to challenge the directory from Z to A. The directory challenges the fastest when you press continuously on keys or . When the visitor finds the resident's directory number, he can press the key to call him. The system will call the resident's telephone number to establish a two-way communication. NOTES: Resident's telephone number is never posted

1. THE VISITOR ALREADY KNOWS THE RESIDENT'S DIRECTORY NUMBER, PRESS # AND ENTER THE RESIDENT DIRECTORY NUMBER AND THEN CALL THE RESIDENT.
1. PRESS THE BUTTONS UP OR DOWN TO VIEW NAMES IN THE DIRECTORY (THE FOLDER SCROLLS FASTER WHEN YOU PRESS HIGH OR LOW KEYS CONTINUOUSLY).
2. WHEN THE NAME IS FOUND, PRESS THE CALL BUTTON.

in front of the visitor. The resident responds to the call and speaks with the visitor about whether or not they should grant access to the residence. The resident can use his phone keyboard to grant access by operating the access relay; for this purpose he presses the key. After granting the entrance, the system stops communication with the visitor and calls from the resident. The resident can cut off his communication with the visitor without granting access by pressing or hanging up. NOTES: The communication cut by hanging up is not

1. WHEN THE RESIDENT ANSWERS THE CALL, HE SPEAKS WITH THE VISITOR.

recommended. The system then stays in control of the line until the maximum conversation time with the visitor is exhausted (this default duration was set at 60 seconds). The maximum conversation time with the visitor can be scheduled from 10 to 180 seconds. Ten and five seconds before disconnection, a tone is heard in the phone to remind the resident of the next cut. To restart the timer, a resident can press the button on his/her phone. Request for entry with an access code Residents and authorized personnel have up to 40 seconds to enter their access code.

Linear Telephone Entry System (AE-100) — System Instructions AE-100 Request for visitor to enter by call diagram (page 23)
Fig. 14 · System Instructions AE-100 Request for visitor to en…

PRESS THE STAR KEY FIRST TO RESET THE DIGITAL KEYBOARD (OPTIONAL), THEN ENTER THE DIRECTORY NUMBER OR INDEPENDENT ACCESS CODE.

EIGHT SECONDS ARE TOLERATED BETWEEN EACH KEYSTROKE.

MAXIMUM 40 SECONDS ARE ALLOWED TO ENTER A COMPLETE ACCESS CODE.

1. Press first to reset the digital keyboard (optional), then enter access code. 2. When the access code has been entered, the access relay is activated. It is possible to use the directory numbers or independent access codes. An eight-second interval is allowed between each keystroke. All numbers in the access code must be entered.

THE FOUR DIGITS MUST BE ENTERED, INCLUDING ZEROS AT THE BEGINNING.

IF YOU ARE WRONG, PRESS THE STAR KEY TO START ENTERING AGAIN.

THE DIGITAL KEYBOARD LOCKS AFTER A NUMBER OF INCORRECT ENTRIES.

Example: The access code has four digits and the code is 0042, user must enter "0 0 4 2". In case of error, press the key to reset the digital keyboard. Enter the correct code again. If the number of tests with an incorrect code exceeds the number that triggers locking on the digital keyboard, it locks and n- accepts more than 90 seconds. Reminder by the resident If the Resident's Reminder function is activated, the resident can call Unit AE-100 to speak with a visitor and grant entry. The callback must be made within 60 seconds of the visitor's missed call.

WHEN A CORRECT CODE IS ENTERED, ACCESS RELAYS ARE ACTIVATED.

Linear Telephone Entry System (AE-100) — System Instructions AE-100 Request for visitor to enter by call diagram (page 23)
Fig. 15 · System Instructions AE-100 Request for visitor to en…
1. CALL THE SYSTEM WITHIN 60 SECONDS OF A MISSED VISITOR'S CALL.
2. THE SYSTEM RESPONDS AND A SHORT BEEP SOUNDS.
1. The resident shall call the telephone number of the system within 60 seconds after its last use. 2. The system responds and a short beep sounds. 3. After talking to the visitor, the resident can tap his access code to allow entry or he may press the star key to refuse access.
Show 13 more labels / short text on this page
➙
Page 24 of the Linear Telephone Entry System (AE-100) user manual — Troubleshooting Blowout on the phone line
Page 24 · click to enlarge
Page 24

Troubleshooting Blowout on the phone line

Linear Limited Warranty This linear product is guaranteed against all manufacturing and labour defects for twenty-four (24) months. This guarantee is granted exclusively to wholesalers who purchase directly from Linear or via the normal linear distribution channels. Linear does not guarantee this product to consumers. Consumers must inquire with their distributor or reseller as to the nature of the warranty that they are given by the dealer or retailer, if any. Linear LLC does not incur any obligation or liability for indirect damage caused by, or in connection with the use or performance of, this product, as well as other consequential damages relating to loss of property and income, lost profits, and costs of removal, installation or relocation. All implied guarantees, including implicit warranties of market value and adaptation to a particular purpose or use shall be valid exclusively until the date on which the guarantee expires. Linear LLC's warranty is granted in lieu of any other explicit or implicit warranties. All product returns involving the warranty must be issued a Product Return Authorization Number (PRN). Please contact Linear Technical Services at 1-800-421-1587 for a NAPP and other important details.

1. Disconnect the 16 Vca fi ls coming out of the terminal; if the buzz stops, one side of the transformer's f i ls is put to earth. 2. Check all connections to detect any short circuits with earthing. Digital keyboard does not activate a relay
1. The access code was not assigned. 2. The digital keyboard may be locked due to too many incorrect access attempts. Wait 90 seconds for the keyboard to unlock and try again. Resident's phone doesn't ring when a visitor calls
1. The resident's phone number is incorrectly scheduled. 2. Check the AE-100 telephone line. 3. Call the resident on another line or mobile phone to determine if his/her telephone is working.

NOTICE OF THE FEDERAL (USA) COMMUNICATION CONTROL AGENCY (FCC) Changes or modifications not explicitly described in this manual or not approved by the manufacturer may cancel the user's device licence. This equipment was tested and found to be in compliance with the FCC Part 15 regulations for Class B digital devices. These limits are intended to provide reasonable protection against interference harmful to residential facilities. This equipment generates, uses and can radiate energy in radio frequencies, and if it is not installed or used as directed, it may cause interference harmful to communications via radio. However, there is no guarantee that interference will not occur in a particular facility. If this equipment produces pests harmful to the reception of radio or television signals, which can be determined by stopping and re-starting the equipment, users are encouraged to try to remedy these noises in one of the following ways:

Reorientation or moving the receiving antenna. By increasing the distance between equipment and receiver. By connecting the equipment to a outlet of an electrical circuit different from that on which the receiver is connected. By consulting the distributor or a specialist radio/TV technician.

Derechos reservados Copyright © 2007 Linear LLC 227625 A

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Linear Telephone Entry System (AE-100)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Telephone Entry System (AE-100)

Be the first to ask — other owners or our team will answer.

Original document

Linear Telephone Entry System (AE-100) manual PDF

24 pages·758 KB·Home Security System·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…