EN
Linear logo
Official user manual

Linear RE-BWC

1 pages·175 KB·Home Security System·PDF·ENDEFRITNLJA
Linear RE-BWC
Table of Contents 30 sections RECONNECT THESE · TWO CONNECTORS · 1. REMOVE CIRCUIT BOARD · PRODUCT DESCRIPTION · … ShowHide
Page 1 of the Linear RE-BWC user manual — SECURE THE CAMERA ASSEMBLY
Page 1 · click to enlarge
Page 1
Linear RE-BWC — RECONNECT THESE diagram (page 1)
Fig. 1

RECONNECT THESE

TWO CONNECTORS

Linear RE-BWC — RECONNECT THESE diagram (page 1)
Fig. 2
RE-BWC Black & White CCTV Camera Installation Instructions (760) 438-7000 • FAX (760) 438-7043 USA & Canada (800) 421-1587 & (800) 392-0123 Toll Free FAX (800) 468-1340 www.linearcorp.comPRODUCT DESCRIPTION1. REMOVE CIRCUIT BOARD Linear’s Model RE-BWC (P/N ACP00886) CCTV camera can be installed inside the RE-1 Entry System. The camera provides a video signal for viewing the area in front of the entry system The camera is continuously powered by the RE-1. The camera’s infrared light emitters illuminate the area directly on front of the entry system for nighttime or low light operation. The camera focus has been factory adjusted to a range of three to four feet. The RE -1 CAMERA jack is used to connect the camera to the main circuit board with the double-ended modular cable supplied with the camera. This cable routes power to, and video from the camera. The RE-1 VIDEO jack is for connection to a video cable with a Type “BNC” connector. Up to 300 feet of 75-ohm RG-59 video cable can be used. Longer cable runs may require the use of a video amplifi er. NOTE: If camera is being installed on an existing installation, power must be off prior to removing circuit board.DISCONNECT THESE TWO CONNECTORS REMOVE CIRCUIT BOARD REMOVE THESE 4 SCREWS 2. MOUNT THE CAMERA3. CONNECT LIGHTING POWER4. REPLACE CIRCUIT BOARD SECURE THE CAMERA ASSEMBLY WITH TWO SCREWS IMPORTANT! TO PREVENT INTERNAL INFRARED LIGHT FROM ENTERING THE CAMERA, BE SURE THE FOAM GASKET AROUND THE CAMERA'S LENS PRESSES FIRMLY AGAINST THE RE-1'S FACEPLATEINSERT WIRING HARNESS PLUG INTO THE 2-PIN LIGHTING CONNECTORRECONNECT THESE TWO CONNECTORS REPLACE CIRCUIT BOARD SECURE WITH 4 SCREWS 5. CONNECT CAMERA CABLE6. CONNECT VIDEO CABLELINEAR LIMITED WARRANTY

1. REMOVE CIRCUIT BOARD

Linear’s Model RE-BWC (P/N ACP00886) CCTV camera can be installed inside the

RE-1 Entry System. The camera provides a video signal for viewing the area in front

Linear RE-BWC — 1. REMOVE CIRCUIT BOARD diagram (page 1)
Fig. 3

PRODUCT DESCRIPTION

NOTE: ALTERNATELY, THE CAMERA CAN BE

CONNECTED DIRECTLY TO ANY OF LINEAR'S

KEEPSAFER™ BRAND MONITORS

RE-1

CAMERA

JACK

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 • FAX (760) 438-7043

Toll Free FAX (800) 468-1340

www.linearcorp.com

Installation Instructions

SECURE THE CAMERA ASSEMBLY

LENS PRESSES FIRMLY AGAINST

Black & White

AND THE RE-1'S CAMERA JACK

CCTV Camera

WITH TWO SCREWS

BE SURE THE FOAM GASKET

RE-BWC

PLUG THE CAMERA CABLE

INTO THE CAMERA'S JACK

TO PREVENT INTERNAL

ENTERING THE CAMERA,

AROUND THE CAMERA'S

INFRARED LIGHT FROM

THE RE-1'S FACEPLATE

IMPORTANT!

CAMERA'S JACK

CABLE FROM

CAMERA

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Linear RE-BWC

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear RE-BWC

Be the first to ask — other owners or our team will answer.

Original document

Linear RE-BWC manual PDF

1 pages·175 KB·Home Security System·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…