EN
Linear logo
Official user manual

Linear MDT

2 pages·133 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear MDT
Table of Contents 73 sections STEP 2B MDRM/MDRM2 Program button and LED · TRANSMITTERS PRESS · WITH MULTI-BUTTON · THE DESIRED BUTTON · … ShowHide
Page 1 of the Linear MDT user manual — MegaCode Series
Page 1 · click to enlarge
Page 1

MDT - Single-channel transmitter with a button on the front and the

MDT-2 - Three-channel transmitter with two buttons on the front and

MDT-4 - Five-channel transmitter with four buttons on the front and

STEP 2B MDRM/MDRM2 Program button and LED

Location. Locate the program button and LED on the back of the

STEP 4 Add additional transmitters. Repeat Step 3 for each

transmitter used with the receiver. Be sure to press the receiver’s

program button each time a new transmitter or a different

transmitter button on a multi-button transmitter is pressed.

If the LED doesn’t come on when the receiver’s program button is

pressed, the receiver’s memory is full. Use the erase function (Step 7)

one button on the top (each button performs a separate function).

one button on the top (each button performs a separate function).

TRANSMITTERS PRESS

WITH MULTI-BUTTON

THE DESIRED BUTTON

MDT MDT-2 MDT-4

P R O G R A I N

to remove transmitters form the receiver’s memory.

THEN PRESS TRANSMITTER BUTTON

top (both buttons perform the same function).

L E

PRESS CHANNEL 1 OR CHANNEL 2

PROGRAM BUTTON FIRST

C H A N N E L O N E

C H A N N E L T O

P R O G R A I N

P R O G R A I N

receiver case.

CH2 CH1

B U T T O

B U T T O

The MegaCode series of digital transmitters are wireless radio controls

designed for use with automatic garage door and gate openers. The

MegaCode radio format provides unparalleled security. The system

MegaCode transmitters and receivers do not contain a typical “coding

switch” as in Linear’s standard digital receivers. Each transmitter is

pre-set at the factory to a unique code. The receiver is programmed by

sending a signal to it from the transmitter(s) that are going to be used

with it. This stores the transmitter’s code into the receiver’s memory.

The receiver will retain its memory even without power. The receiver

will activate only from these “memorized” transmitters. Please refer to

The transmitters are powered from two Type 2032 lithium “button cell”

batteries. When the batteries get low, the bright red LED light on the

transmitter will start to dim as the unit is activated. When the red LED

no longer lights when the transmitter is activated, the batteries should

STEP 2A MDR/MDRNR/MDR2 Program button and LED

Location. Locate the program button and LED on the side of the

PROGRAMMING

IS READY, PRESS THE DESIRED

CHANNEL ONE

PROGRAMMING

CHANNEL TWO

PROGRAMMING

the receiver’s instructions for maximum transmitter capability.

can be programmed to more than a million different codes.

TRANSMITTER BUTTON

LED

BUTTON

BUTTON

WHEN RECEIVER

AS TRANSMITTER

IS ENTERED INTO

RECEIVER LED

WILL FLICKER

PROGRAMMING

MEMORY

CHANNEL 1

BUTTON

LED WILL LIGHT

WHEN RECEIVER

IS READY

CH2 CH1

DESCRIPTION

receiver case.

PROGRAMMING

be replaced.

CHANNEL 2

BUTTON

STEP 1 Receiver Installation. Connect the receiver to the

garage door operator as described in the receiver’s Installation

STEP 3 Program receiver. Momentarily press the receiver’s

program button (channel one or two). The red programming LED

will light if there’s room in the receiver’s memory for another

transmitter. The LED stays on for about 5 seconds. A transmitter

must be entered while the LED is on. Press the desired

transmitter button. The LED will flicker indicating that the receiver

¯ NOTEBe sure to press the receiver program button for less than

2 seconds. ¯ WARNING! Door operator will not activate when the receiver

is being programmed from the transmitter, but the door

operator will activate the next time the transmitter is activated

¯ NOTEThe programming LED also monitors radio signals entering

the receiver. It is common to see an occasional blink from the LED.

The LED will also light when any transmitter tuned to the receiver’s

Instructions. Apply power to the operator before programming.

frequency (programmed into the receiver or not) is activated.

MDT

CONNECT RECEIVER TO GARAGE DOOR OPERATOR

(800) 421-1587 • www.linearcorp.com

DIGITAL TRANSMITTERS

MDT, MDT-2, MDT-4

Installation Instructions

has accepted the transmitter.

MegaCode Series

after programming.

Page 2 of the Linear MDT user manual — FOR THREE SECONDS
Page 2 · click to enlarge
Page 2

STEP 7 Erasing receiver memory. Transmitters may be

erased from the receiver’s memory by pressing and holding the

receiver’s program button (channel one or two) for 5 seconds or

more. After the LED blinks (count of transmitters) it will blink one

more time for channel one and twice for channel 2 as the

receiver’s memory for that channel is erased. All transmitters

Copyright © 1999 Linear Corporation 207779 D

INFO 2 Visor Clip Removal. The visor clip can be removed

by removing the three screws as shown. Slide the clip off the

Linear radio controls provide a reliable communications link and fill an

1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited

1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating

1 Changes or modifications to the device may void FCC compliance. 1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be

AS THE TRANSMITTERS ARE ERASED

TOTAL NUMBER OF TRANSMITTERS

THEN IT WILL BLINK ONE MORE TIME

for each receiver channel are erased at the same time.

LED WILL FLASH, COUNTING THE

PROGRAMED TO THAT CHANNEL.

BY REMOVING THREE

REMOVE VISOR CLIP

retaining plate and reattach the plate to the transmitter.

CH2 CH1

FROM THAT CHANNEL

Linear MDT — CH2 CH1 diagram (page 2)
Fig. 1

transmitter power and therefore limited range.

frequencies, regardless of code settings.

communicated to the ultimate users.

limitations which must be observed.

FOR FIVE SECONDS OR MORE

PRESS PROGRAM BUTTON

(CHANNEL 1 OR 2)

IMPORTANT !!!

CH2 CH1

STEP 6 Test receiver. Be sure door area is clear. Activate

each transmitter. The receiver relay should click (relay output

models only) and the operator should activate. Wait 2 seconds

INFO 1B Replacing transmitter batteries. Replace the two

batteries with two Type 2032 lithium batteries or equivalent. The

batteries stack on top of each other with the (+) sides facing the

front of the transmitter. Replace with new batteries then close the

battery compartment, replace battery access screw and test

This product is warranted to the consumer against defects in material and

workmanship for one year from the date of purchase. This warranty applies

to first retail buyers of new devices. Warrantor will repair, or at its option,

replace, any device it finds that requires service under this warranty, and

will return the repaired or replaced device to the consumer at the

warrantor’s cost. For warranty service and shipping instructions contact

warrantor at the address shown below. Devices must be sent to warrantor

for service at owner’s expense. The remedies provided by this warranty

are exclusive. Implied warranties under state law are to the one year period

of this written warranty. Some states do not allow limitations on how long

an implied warranty lasts, so the above limitation may not apply to you. In

order to be protected by this warranty, save your proof of purchase and

send copy with equipment should repair be required. This warranty gives

you specific legal rights, and you may also have other rights which vary

All products returned for warranty service require a Return Product

Authorization Number (RPA#). Contact Linear Technical Services at

PRESS TRANSMITTER

BUTTON TO TEST

1-800-421-1587 for an RPA# and other important details.

SIDE UP

OF OBSTRUCTIONS

BE SURE DOOR

AREA IS CLEAR

between each activation.

LIMITED WARRANTY

WARNING!

from state to state.

WITH TWO

BATTERIES

REPLACE

TYPE 2032

transmitter.

STEP 5 Review memory. Press and hold the receiver’s

program button (channel one or two) until the LED begins to flash

(about 3 seconds) and then release the button. Count the number

of flashes. The number of flashes equals the number of

¯ NOTEDon’t hold down the programming button longer than

5 seconds, the receiver’s memory for that channel will be erased (Step 7).

INFO 1A Opening battery compartment. To access the

transmitter’s batteries remove the battery access screw on the

back of the unit. Flip the unit over so that the front is facing you.

¯ NOTEThe same transmitter (or the same transmitter button on

multi-button transmitters) cannot be programmed into both

¯ NOTEIf the receiver’s LED flashes continuously when a

transmitter isn’t being activated, the receiver is too close to an

electrical noise source. Move the receiver away from the noise

COMPARTMENT OPEN

TOTAL NUMBER OF TRANSMITTERS

transmitters programmed into that channel of the receiver.

LED WILL FLASH, COUNTING THE

PROGRAMED TO THAT CHANNEL

Use a small screwdriver to open the battery compartment.

SWING BATTERY

CH2 CH1

TRANSMITTER

source or call technical services for assistance.

CONTINUOUSLY FLASHING LED MAY

FLIP

OVER

INDICATE ELECTRICAL NOISE

CH2 CH1

INTERFERRENCE

PRESS PROGRAM BUTTON

receiver channels 1 and 2.

FOR THREE SECONDS

(CHANNEL 1 OR 2)

CH2 CH1

THEN RELEASE

REMOVE BATTERY

ACCESS SCREW

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Linear MDT

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear MDT

Be the first to ask — other owners or our team will answer.

Original document

Linear MDT manual PDF

2 pages·133 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…