Instruction/ maintenance manual of the product SDU50 Frymaster
Go to page of 13
Frymaster, a member of the Comm ercial Food Equipment Service Association, recommends using CFESA Certified Technicians. 24-Hour Service Hotline 1-800-551-8633 SEPTEMBER 2005 www.
ii NOTICE IF, DURING THE WARRANTY PERIOD, THE CU STOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHE R THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR AN Y OF ITS AUTHORIZED SERVICE CENTERS, AND/OR THE PART BEI NG USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID.
iii Shortening Disposal Unit (SDU) Installation, Operation, Service, and Parts Manual TABLE OF CONTENTS Page 1. INTRODUCTION 1 1.1 Service Information and Parts Ordering ..............................................1 1.2 Installation, Operating and Service Personnel .
SHORTENING DISPOSAL UNIT (SDU 50, SDU 90 AND BKSDU) INSTALLATION, OPERATION, SERVICE AND PARTS 1 1. INTRODUCTION 1.1 Service Information and Parts Ordering Included with the unit when shipped from the factory is a list of Factory Au thorized Service Cen ters (FASCs).
2 manuals, and to stock a minimum amount of parts for F rymaster equipment. A list of Factory Authorized Service Centers (FAS Cs) was included with this equipment when shipped from the factory. Unless specifically indica ted ot herwise in this manual, failure to use q ualified service personnel will void the Frymaster Warranty on this equipment.
3 With the cover open, the top of the tank is 9¾ in ches (248 mm) above the floor, permitting it to be positioned directly beneath the dra ins of most fryers.
4 DANGER Before each use inspect the cover to ensure the cover gasket is present and properly placed. DO NOT use the disposal unit if this gasket is damaged or missing. 3. Slowly open the drain valve. Regulate flow w ith the drain valve to prevent splashing.
5 6. On BKSDU units, the built-in heater may be connected to a grounded 120VAC or 240VAC receptacle to prevent shortening from solidifyi ng in the tank when immediate transfer to a disposal container is not possible. 2.4 Cleaning Clean the crumb screen with a solution of detergent and water.
6 2. Remove the five screws securing the front cover and remove the cover. If replacing the pump shaft seal only, remove the old seal and install the replacem ent as shown in the illustration below, then go to Step 5. If replacing the pump vanes, go to Step 3.
7 4. PARTS LIST 5 17 22 23 32 31 33 9 28 1 2 3 4 6 7 8 10 12 13 11 14 15 16 20 21 25 26 27 29 16 11 30 18 34 38 37 36 35 19 NOTE: See Pag e 6 for BK SDU pump assembly components .
8 Item Part # Component 1 Pipe Assembly, Discharge 823-4600 Standard (includes Item 2) (use 823-4617 for BKSDU) 823-4598 For use with Item 4 (Hose Discharge) (includes Item 3) 2 813-0115 Nipple, ¾-in.
9 NOTE: T he BKSDU pum p assem bly is identical to the SDU 50/SDU 90 pum p as sem bly except for the addition of the pump c over and insulation and the m odified dischar ge pipe ass em bly.
Frymaster, L.L.C., 8700 Line Av enue, PO Box 51 000, Shreveport, Louisiana 71135-1000 Shipping Address: 8700 Line Av enue, Shreveport, Louisiana 71106 TEL 1-318-865-1711 FAX (Par ts) 1-318- 688-2200 F.
An important point after buying a device Frymaster SDU50 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Frymaster SDU50 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Frymaster SDU50 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Frymaster SDU50 you will learn all the available features of the product, as well as information on its operation. The information that you get Frymaster SDU50 will certainly help you make a decision on the purchase.
If you already are a holder of Frymaster SDU50, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Frymaster SDU50.
However, one of the most important roles played by the user manual is to help in solving problems with Frymaster SDU50. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Frymaster SDU50 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
