Instruction/ maintenance manual of the product WESY85290 Weider
Go to page of 25
USERÕS MANUAL QUESTIONS? As a manufacturer , we are com- mitted to complete customer sat- isfaction. If you have questions, or if there are missing/damaged parts, we will guarantee you com- plete satisfaction through direct assistance from our factory .
2 LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. It is the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 3. If you feel pain or dizziness at any time while exercising, stop immediately and begin cool- ing down.
4 ASSEMBLED DIMENSIONS: Height: 76 in. Width: 38 in. Length: 59 in. Leg Press Plate Low Pulley Station Foot Plate High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Weight Stack Seat Backrest Weight Pin Lat Bar Holder Thank you for selecting the versatile WEIDER ¨ 8620 Home Gym System.
5 1 56 High Side of Bracket 3 5 51 51 14 1 4 1 Before beginning assembly , carefully read the following information and instructions: ¥ Place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.
6 FRAME ASSEMBL Y 2. Slide the Front Upright (42) onto the 5/16Ó x 2 1/2Ó Carriage Bolts (1) in the Base (4). Hand tighten a 5/16Ó Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. 3. Press a 2Ó Square Inner Cap (27) into the open end of the T op Frame (55).
7 FRAME ASSEMBL Y ARM ASSEMBL Y 5. Press the Weight Tube Bumper (64) into the end of the Weight Tube (63). Insert the Weight Tube into the stack of W eights (25). Be sure that the pins on the Weight T ube are resting in the pin grooves in the upper Weight.
8 ARM ASSEMBL Y 8. Press a 1 3/4Ó Square Inner Cap (44) into the top of a Press Arm (46). W et the handle on the Press Arm with soapy water . Slide a Handgrip (31) onto the handle.
1 1. Press a 1 3/4Ó Square Inner Cap (44) into the Seat Frame (36). Attach a Bumper (73) to the Seat Frame with a 1/2Ó T ap Screw (65). Slide the Seat Frame (36) onto the 5/16Ó x 2 1/2Ó Carriage Bolts (1) in the Base (4). See the inset drawing. The bracket on the Seat Frame must be behind the Press Frame (17).
14. During steps 15 through 29, refer to the CABLE DIAGRAM on page 19 of this manual to verify proper cable routing. Before begin- ning this section, identify the Long Cable (23) and the Short Cable (58) by comparing the lengths of the cables. IMPORT ANT : While assembling the cables, do not overtighten the bolts and nuts securing the pulleys.
11 18. Route the Long Cable (23) around the ÒVÓ- Pulley (6) on the Right Arm (48). Be sure that the Cable is in the groove of the ÒVÓ- Pulley and that the Long Cable T rap (50) is turned to hold the Cable in place. T ighten the 3/8Ó x 2 1/2Ó Bolt (7) and the 3/8Ó Nylon Locknut (not shown).
12 22. Locate the Short Cable (58). Route the Short Cable under the 3 1/2Ó Low Pulley (77). Be sure that the end of the Cable with the ball is on the indicated side of the Pulley and that the Cable is between the Pulley and the welded spacer on the Leg Lever (29).
13 26. Note: The 3 1/2Ó Pulley (15) labeled in this step is pre-attached. It is shown removed for easy part identification. Route the Short Cable (58) around the 3 1/2Ó Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable is routed around the Pulley as shown.
14 29. Attach the Long Cable (23) to the Small ÒUÓ- Bracket (67) with a 1/4Ó Nylon Locknut (2) and a 1/4Ó Flat W asher (10). Do not com- pletely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.
15 32. Press a 1 3/4Ó Square Inner Cap (44) into the Press Adjustment T ube (79). Align one set of holes in the Press Adjustment T ube (79) with the holes in the Rocker Arm (32). Insert the ÒLÓ-Pin (40) through the holes. Be sure that the Press Adjustment T ube is oriented as shown.
16 The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise.
17 ADJUSTING AND REMOVING THE LEG PRESS PLA TE AND ADJUSTMENT TUBE T o adjust the position of the Leg Press Plate (78), remove the ÒLÓ-Pin (40) from the Press Adjustment T ube (79) and the Rocker Arm (32). Align a different set of holes in the Press Adjustment Tube with the set of holes in the Rocker Arm.
18 Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used.
19 The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use the diagram to be sure that the two cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the home gym system will not function properly and damage may occur .
1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 1 3/4" Square Inner Cap (44) 2" Square Inner Cap (27) 2" Squar.
1/4" Flat W asher (10) 5/16" Flat W asher (8) 3/8" Flat W asher (9) 1/4" x 2 1/2" Screw (43) 5/16" x 1 3/4" Bolt (72) 5/16" x 2 1/2" Carriage Bolt (1) 5/16.
1" Retainer (69) 3/8" Nylon Locknut (21) 3/8" Nylon Jam Nut (33) 3/8" x 2" Bolt (12) 3/8" x 3 1/2" Bolt (16) 3/8" x 2 1/2" Bolt (7) 3/8" x 3 3/4".
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty . Description 1 4 5/16Ó x 2 1/2Ó Carriage Bolt 2 3 1/4Ó Nylon Locknut 3 20 5/16Ó Nylo.
7 50 6 21 69 70 69 70 47 48 44 45 44 45 74 74 11 11 8 8 55 27 12 15 44 15 71 23 21 44 21 49 3 61 60 56 15 3 21 6 50 7 42 66 68 55 3 21 66 15 20 12 12 2 57 58 21 3 5 19 26 51 25 64 63 76 9 21 10 43 10 .
T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
An important point after buying a device Weider WESY85290 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Weider WESY85290 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Weider WESY85290 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Weider WESY85290 you will learn all the available features of the product, as well as information on its operation. The information that you get Weider WESY85290 will certainly help you make a decision on the purchase.
If you already are a holder of Weider WESY85290, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Weider WESY85290.
However, one of the most important roles played by the user manual is to help in solving problems with Weider WESY85290. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Weider WESY85290 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
