Instruction/ maintenance manual of the product WESY59101 Weider
Go to page of 35
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in the literature. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76.0 in. Width: 86.5 in. Length: 91.5 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arms Leg Press Seat .
5 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y .” See the inset drawing. Insert two 1 1/2” x 2 1/2” Inner Caps (83) and two 3/8” x 2” Carriage Bolts (92) into the Butterfly Base (4). Insert two 1 1/2” x 2 1/2” Inner Caps (83) into the indicated ends of the Butterfly Base (4) and the Press Base (6).
5. Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat W ashers (48), and two 3/8” Nylon Locknuts (50). Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat W ashers (48) and two 3/8” Nylon Locknuts (50).
8 89 48 48 48 89 51 6 50 48 21 Slot 15 9. See the inset drawing. Insert two Weight Inserts (56) into each Weight (21). Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6). Slide the Weight Guides (15) through the Weight Bumpers (51) and the holes in the Press Base (6).
9 48 62 50 48 33 9 12. Secure the Press T op Frame (9) to the Butterfly T op Frame (33) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat W ashers (48), and two 3/8” Nylon Locknuts (50).
10 15 48 48 10 84 28 10 28 48 48 53 53 15. Insert a 2” Square Inner Cap (28) into the end of the Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm (10) with two 3/8” x 1” Bolts (84) and two 3/8” Flat W ashers (48). Repeat this step with the other Butterfly Arm (10).
21. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Locate the Butterfly Cable (73), which is the shorter cable of the two that have eyelets on both ends. Attach the Butterfly Cable (73) to the Right Pivot Arm (85) with a 5/16” x 2 1/4” Shoulder Bolt (79) and a 5/16” Nylon Jamnut (101).
12 23. Remove the preassembled 3/8” x 2” Bolts (54) from one set of Adjustable Pulley Plates (23). Wrap the Butterfly Cable (73) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable T rap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
13 27. Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). Insert the Ab Cable down through the Press T op Frame (9). Attach a 3/8” Flat W asher (48) and a 5/8” x 3/4” Bushing (66) to a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press T op Frame and the 3 1/2” Pulley .
14 31. Locate the Weight Cable (72). Note that one end of the Weight Cable has a bolt, and the other end has a ball on it. Lay the Weight Cable (72) inside the bracket on the Butterfly Base (4) in the manner shown. Attach a 3 1/2” Pulley (24) to the bracket with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
15 36 37 38 35. Wrap the Weight Cable (72) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable T rap (25) to the Butterfly Upright (1) with a 3/8” x 4” Bolt (59), a 3/8” Flat W asher (48), and a 3/8” Nylon Jamnut (63). Be sure that the Cable T rap is turned to hold the Cable in place.
16 39. Wrap the Weight Cable (72) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable T rap (25) between the lowest holes in the Adjustable Pulley Plates (23) hanging from the Ab Cable (47) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50) that was removed in step 28.
17 43. Locate the Leg Press Cable (75). Attach the Leg Press Cable to the indicated side of the Press Upright (2) with a 3/8” x 3 1/4” Bolt (62) and a 3/8” Nylon Locknut (50). Do not tighten the Nylon Locknut yet. Wrap the Leg Press Cable (75) up around a 3 1/2” Pulley (24) in the direction shown.
18 47. Remove the 3/8” Nylon Locknut (50) from the indi- cated 3/8” x 5 1/2” Bolt (55). Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Secure the 3 1/2” Pulley and a Cable T rap (25) to the 3/8” x 5 1/2” Bolt (55) on the indi- cated side of the Press Base (6) with the 3/8” Nylon Locknut (50).
19 51. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4” x 3/4” Bolts (49). Repeat this step with the other Seat (not shown) and the Press Seat Frame (not shown).
Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly , find and correct the problem. IMPORT ANT : If the cables are not properly installed, they may be damaged when heavy weight is used.
21 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise.
22 A TT ACHING THE AB STRAP TO THE AB PULLEY ST A TION Attach the Ab Strap (81) to the Ab Cable (47) at the ab pulley station with a Cable Clip (69). ADJUSTING THE BACKREST T o adjust a Backrest (12),.
23 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 10 lb. top weight. The other numbers refer to the 10 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
25 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the Ab Cable (47), the Butterfly Cable (73), and the Weight Cable (72). Use the diagrams to be sure that the Cables have been assembled correctly .
26 Weight Cable (72) 2 3 1—Low Pulley 4 8 11 12—Weight Stack 7 6 5 Cable ID 72 47 75 73 9 10.
27 NOTES.
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain Time (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
Note: The assembly procedure is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , and 4) seat assembly . The hardware for each stage is packaged separately . W AIT UNTIL YOU BEGIN EACH ASSEMBL Y ST AGE TO OPEN THE P ARTS BAG LABELED FOR THA T ASSEMBL Y ST AGE.
5/16" Nylon Jamnut (101) Cable Clip (69) "V" Pulley (27) (Not shown to scale) 3 1/2" Pulley (24) (Not shown to scale) Retainer Ring (31) 4 1/2" Pulley (82) (Not shown to scale.
5/16" x 2 1/4" Shoulder Bolt (79) 3/8" x 1" Bolt (84) 3/8" x 1 3/4" Bolt (57) 3/8" x 1 1/4" Button Head Bolt (98) 1/4" x 3/4" Bolt (49) 3/8" x 4&.
2" x 3” Inner Cap (78) 2" Square Inner Cap (28) 1 1/2" Square Inner Cap (35) 1 1/2" x 2 1/2” Inner Cap (83) 2 1/2" Square Inner Cap (76).
8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
P ART LIST—Model No. WESY59101 R0103A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
92 92 49 39 49 23 25 24 25 24 23 50 54 23 25 24 25 24 23 50 44 35 49 86 65 77 28 65 86 77 64 25 24 60 96 68 36 25 24 50 8 68 29 36 68 36 63 25 24 25 24 60 90 78 62 48 50 80 40 20 50 83 6 60 24 25 50 5.
An important point after buying a device Weider WESY59101 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Weider WESY59101 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Weider WESY59101 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Weider WESY59101 you will learn all the available features of the product, as well as information on its operation. The information that you get Weider WESY59101 will certainly help you make a decision on the purchase.
If you already are a holder of Weider WESY59101, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Weider WESY59101.
However, one of the most important roles played by the user manual is to help in solving problems with Weider WESY59101. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Weider WESY59101 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
