Instruction/ maintenance manual of the product WESY49310 Weider
Go to page of 33
QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through direct assis- tance from our factory .
1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. Use the weight system only on a level sur- face.
3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in. Width: 1 10 in. Length: 92 in. Foot Plate High Pulley Station Lat Bar Leg Lever Butterfly Arms Assist Arm Press Arm Weight Stacks Backrests Dip .
4 ASSEMBL Y 1 8 11 51 27 1 4 3 1 51 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press two 2” Square Outer Caps (51) onto the Stabilizer (5).
5 2. Slide the Assist Upright (74) and the Leg Press Upright (56) onto the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the Uprights should be on the side shown. Hand-tighten four 5/16” Nylon Locknuts (3) onto the Carriage Bolts.
6 4. Press a 2” Square Inner Cap (27) into the end of the T op Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the T op Frame.
7 7. Press a Weight Tube Bumper (64) into the end of the Short Weight Tube (108). Insert the Weight Tube into the front stack of W eights (25). Be sure that the pin on the W eight T ube is sitting in the pin grooves in the top Weight. Lubricate the inside of the holes in a T op Weight (65).
8 9. Attach the upper ends of the Short Weight Guides (73) to the T op Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) in the same manner .
9 12. Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).
10 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (101) with two 5/16” x 2 1/4” Bolts (33) and two 5/16” Nylon Locknuts (3). Press two 1 1/2” Square Inner Caps (32) into the Military Press Arm (84). Press two 1” Round Inner Caps (49) into the Military Press Arm.
11 17. Attach the Left Pull-up Arm (75) and the Right Pull-up Arm (77) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3). Attach the Left Dip Arm (78) and the Right Dip Arm (79) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3).
12 20. Wrap the High Cable (58) around a “V”-Pulley (50). Attach the “V”-Pulley and a Long Cable T rap (31) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the Long Cable T rap is positioned to hold the Cable in place.
13 24. See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable T rap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable T rap is inside the Long “U”- Bracket.
14 27. Locate the Low Cable (23). Route the Low Cable under the 3 1/2” Low Pulley (102). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the crossbar on the Press Frame.
15 31. Attach the end of the Low Cable (23) to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing.
16 34. Wrap the Military Press Cable (72) around a “V”-Pulley (50). Attach the “V”-Pulley to the T op Frame (55) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Wrap the Military Press Cable (72) around a 3 1/2” Pulley (15).
17 36. Slide a 5/16” Flat W asher (8) onto a 5/16” x 2 3/4” Bolt (1 1). Insert the Bolt through the indi- cated hole in the Pivot Arm (101). The Bolt must be inserted from the side shown. Fully tighten a 5/16” Nylon Jam Nut (93) onto the Bolt.
18 38. Locate the Leg Press Cable (99). Attach the end of the Leg Press Cable to the Long “U”- Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.
19 40. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Insert a 1/4” x 2 1/2” Carriage Bolt (92) through the center hole in a Seat Plate (37).
20 43. Attach the Front Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Flat W ashers (10). The Backrest must be oriented as shown. 44. Press a 1 1/2” Square Inner Cap (32) into the Front Seat Frame (36).
47. Press two 3/4” Round Inner Caps (34) into each Pad T ube (28). Insert a Pad T ube (28) into the Front Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Foam Pad (30) onto each end of the Pad T ube.
22 HOW T O USE THE WEIGHT SYSTEM The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise poster accompanying this manual to see how the weight system should be set up for each exercise.
23 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Front Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Front Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).
24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
26 CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly .
27 Military Press Cable (72) Leg Press Cable (99) Rear Weight Stack— 1 2 3 4 7 6 5 3 2 4 — Rear Seat Frame 8 — Pivot Arm 1 — Long “U”-Bracket Military Press Cable (72) and Leg Press Cable .
5/16" Nylon Locknut (3) 1/4" Flat W asher (10) 5/16" Flat W asher (8) 3/8" Flat W asher (9) 1/4" x 2 1/2" Screw (43) 3/8" Nylon Locknut (21) 1/4" x 2" Mach.
1" Retainer (69) 3/8" x 3 1/2" Bolt (16) 1/4" x 3/4" Screw (18) 5/16" x 5" Bolt (68) 3/8" x 3 3/4" Bolt (88) 3/8" x 8" Bolt (59) Cable Clip (53) .
1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 5/16" x 2" Eyebolt (35) 1 1/2" Square Inner Cap (32) 1 3/4&quo.
P ART LIST—Model No. WESY49310 R1 101A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
60 27 21 50 55 86 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 108 64 25 26 19 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 48.
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
An important point after buying a device Weider WESY49310 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Weider WESY49310 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Weider WESY49310 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Weider WESY49310 you will learn all the available features of the product, as well as information on its operation. The information that you get Weider WESY49310 will certainly help you make a decision on the purchase.
If you already are a holder of Weider WESY49310, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Weider WESY49310.
However, one of the most important roles played by the user manual is to help in solving problems with Weider WESY49310. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Weider WESY49310 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
