Instruction/ maintenance manual of the product SPER0 FRYMATE ML-52920 Vulcan-Hart
Go to page of 12
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 INST ALLA TION & OPERA TION MANUAL SPER1 & SPER2 ELECTRIC FR YERS MODEL SPER1 ML-52918 SPER2 ML-52919 SPER0 Frymate ML-52920 FORM 30729 Rev.
— 2 — Installation, Operation and Care of MODEL SPER1 & SPER2 ELECTRIC FR YERS PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE GENERAL Your Vulcan fryer is produced with quality workmanship and material. Proper installation, usage and maintenance of your fryer will result in many years of satisfactory performance.
— 3 — INSTALLATION CODES AND STANDARDS Your Vulcan fryer must be installed in accordance with: 1. State and local codes. 2. The National Electrical Code, ANSI/NFPA No. 70 (latest edition). Copies may be obtained from The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
— 4 — PL-40545-1 Power On Light High Limit Lights Temperature Controller Power Switch Trouble Light Fry / Melt Switch Heating Light OPERA TION WARNING: HOT OIL AND PARTS CAN CAUSE BURNS.
— 5 — POWER SWITCH — Controls electric supply to fryer (Optional - hood ventilator to interlock.) POWER ON LIGHT — Indicates when electric supply is on. TEMPERATURE CONTROLLER — Maintains frying temperature by controlling power supply. HEATING LIGHT — When on, indicates temperature control is calling for power to the elements.
— 6 — Split Vat 1. Remove crumb screens. 2. Divide a 50-pound block of shortening into two equal halves (approximately 25 pounds each). 3. Place each half of the shortening directly on the heating elements in each well of the fry tank and slide back.
— 7 — PL-40547-1 Drain Valves Drain Nipple 1. Allow shortening to cool before draining or filling. 2. Consult the operating instructions supplied by the manufacturer of your filtering system before filtering the shortening. 3. Firmly screw the fryer drain nipple (supplied) into the fryer drain valve (Fig.
— 8 — SHORTENING MAINTENANCE Shortening life may be extended by following these important procedures. Do not salt foods over the fryer. Use good quality shortening. Filter shortening daily at a minimum. Keep equipment and surroundings clean. Set thermostats correctly.
— 9 — PL-40546-1 Reset Button 7. Turn power switch OFF at termination of burn-off cycle. 8. Heating elements will heat up in excess of 600 ° F glowing red. If any do not glow, call a Vulcan- authorized service agency. Some smoking, crackling sound and puffs of flame will occur.
— 10 — 6. Drain solution and discard. Close drain valve and fill tank half full with water. 7. Scrub entire inside of tank with a stiff bristle nylon brush. 8. Drain solution and rinse tank thoroughly with clean water. 9. Close drain valve and refill tank with clean hot (minimum 140 ° F) water.
— 11 — MAINTENANCE WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE FRYER. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE PERFORMING ANY MAINTENANCE. CALIBRATION PROCEDURES 1. Monitor shortening temperature 1" below the surface with an accurate temperature measuring device.
— 12 — FORM 30729 Rev. A (1-95) PRINTED IN US.A..
An important point after buying a device Vulcan-Hart SPER0 FRYMATE ML-52920 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart SPER0 FRYMATE ML-52920 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart SPER0 FRYMATE ML-52920 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart SPER0 FRYMATE ML-52920 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart SPER0 FRYMATE ML-52920 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart SPER0 FRYMATE ML-52920, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart SPER0 FRYMATE ML-52920.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart SPER0 FRYMATE ML-52920. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart SPER0 FRYMATE ML-52920 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center