Instruction/ maintenance manual of the product GR65F ML-135534 Vulcan-Hart
Go to page of 12
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 OPERA TION MANUAL For additional information on Vulcan-Hart Company or to locate an authorized parts and service provider in your area, visit our website at www.vulcanhart.
– 2 – Table of Contents GENERAL ............................................................................................................................................. 3 ASSEMBLY ..............................................................
– 3 – OPERATION AND CARE OF KLEENSCREEN FILTRATION SYSTEM SAVE THESE INSTRUCTIONS GENERAL The KleenScreen Filtration System filters the oil as it is pumped back to its respective tank. Valves inside the doors under each fry tank must be set so only one tank is being drained, filtered and pumped back at any one time.
– 4 – CONTROLS AND COMPONENT LOCATIONS — Gas Fryers The filter tank cover is removed to show component locations. Fig. 1.
– 5 – CONTROLS AND COMPONENT LOCATIONS — Electric Fryers The filter tank cover is removed to show component locations. Fig. 2.
– 6 – Fig. 3 Fig. 4 Fig. 5 5. Turn the filter power switch ON (Fig. 6). The red pilot light in the filter power switch comes on. PL-41601 PL-41602 PL-41603 PL-41604 Gas Fryer Electric Fryer Fig. 6 OPERATION WARNING : HOT FRYING COMPOUND AND PARTS CAN CAUSE BURNS.
– 7 – 6. To start filtering, pull out the red filter valve handle (Fig. 7) of the fryer tank to be filtered. Use a brush to remove all the residue from the bottom of the tank into the drain tube. Let the oil recycle for 1 to 3 minutes, flushing residue from the tank bottom into the filter.
– 8 – PL-41612 2. Set the fryer thermostat at 350°F (177°C). 3. Once shortening has melted, stir oil to eliminate solid shortening in the cold zone (Fig. 10). All solid shortening must have melted completely. 4. Allow the fryer to idle at 350°F (177°C) for 10 minutes, if filtering from a cold start.
– 9 – PL-41615 PL-41616 3. While holding the discard hose at the base of the fitting, use your free hand to slide the collar away from the end of the female fitting (Fig. 12). Align the male and female parts of the quick disconnect line and push the hose onto the male connector discharge fitting.
– 10 – MAINTENANCE WARNING : HOT FRYING COMPOUND AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE FRYER. USE CARE WHEN FILTERING. WARNING : SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE THE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK.
– 11 – FRYER BOIL-OUT INSTRUCTIONS CAUTION : Do not run water or boil-out solution through the filter motor or pump. Do not use the filter during boil-out or cleaning of the fryer. Before cleaning the fryer, read the entire cleaning instructions provided by the cleaning product's manufacturer.
– 12 – FORM 35616 (Nov. 2003) PRINTED IN U.S.A. 18. After rinsing the tank, close the drain valve and refill the tank with hot water to the - Max - fill line. 19. Add 1 cup (0.2 L) of vinegar per 20 lb (9 kg) of fryer capacity to neutralize any caustic ingredients remaining from the boil-out solution.
An important point after buying a device Vulcan-Hart GR65F ML-135534 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart GR65F ML-135534 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart GR65F ML-135534 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart GR65F ML-135534 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart GR65F ML-135534 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart GR65F ML-135534, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart GR65F ML-135534.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart GR65F ML-135534. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart GR65F ML-135534 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
