Instruction/ maintenance manual of the product 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-13 Vulcan-Hart
Go to page of 20
VULCAN-HART DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC WWW.VULCANHART.COM INST ALLA TION & OPERA TION MANUAL For additional information on Vulcan-Hart or to locate an authorized parts and service provider in your area, visit our website at www .vulcanhart.
— 2 — GR SERIES GAS FRYERS IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREP ARED FOR PERSONNEL QUALIFIED T O INST ALL GAS EQUIPMENT , WHO SHOULD PERFORM THE INITIAL FIELD ST ART -UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
— 3 — GR SERIES GAS FRYERS T ABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY ................................................................................................. 2 INTRODUCTION ..............................................................
— 4 — GR SERIES GAS FRYERS EXTENDING SHORTENING LIFE ........................................................................................... 14 DRAINING THE TANK .................................................................................
— 5 — GR SERIES GAS FRYERS INTRODUCTION GENERAL Vulcan Fryers are produced with quality workmanship and material. Proper installation, usage and maintenance will result in many years of satisfactory performance. Before installing the fryer, thoroughly read this manual and carefully follow all instructions in the order given.
— 6 — GR SERIES GAS FRYERS RECEIVING AND UNPACKING This fryer was carefully inspected before leaving the factory. Upon acceptance of the shipment, the transportation company assumes full responsibility for safe delivery. Immediately after unpacking the fryer, check for possible shipping damage.
— 7 — GR SERIES GAS FRYERS INST ALLA TION WARNING: THIS EQUIPMENT SHALL BE INSTALLED ONLY BY A LICENSED GAS FITTER. Caution: Do not use the door or its handle to lift the fryer.
— 8 — GR SERIES GAS FRYERS Air Supply and Ventilation WARNING: DO NOT OBSTRUCT THE FLOW OF COMBUSTION/ VENTILATION OR AIR OPENINGS AROUND THE FRYER. ADEQUATE CLEARANCE AROUND THE FRYER IS NECESSARY FOR SERVICING AND PROPER BURNER OPERATION. • Install fryer in an area with sufficient air supply for gas combustion at fryer burners.
— 9 — GR SERIES GAS FRYERS FLUE CONNECTION Caution: Ensure that your ventilation system does not cause a down draft at the fryer's flue opening. Down drafts will not allow the fryer to exhaust properly and will cause overheating which may cause permanent damage.
— 10 — GR SERIES GAS FRYERS Quick-Disconnect for Units on Casters For an appliance equipped with casters: • The installation shall be made with a connector that complies with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas Appliances, CAN/CGA-6.
— 11 — GR SERIES GAS FRYERS OPERA TION WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITH- OUT DRAINING ALL FRYING COMPOUND FROM THE TANK.
— 12 — GR SERIES GAS FRYERS CAUTION: Solid shortening should NOT be used with GRM Fryers with millivolt controls. Melting solid shortening will damage the fryer tank and void your warranty. • Close the drain valve. • Fill the fryer tank with liquid shortening.
— 13 — GR SERIES GAS FRYERS TURNING OFF THE FRYER (FREE-STANDING MODELS) 1 . Turn the thermostat OFF. 2 . To keep the pilot lit, turn the gas valve knob to “I” in PILOT. 3 . To shut off all gas to the system, including the pilot, turn the gas valve knob to OFF.
— 14 — GR SERIES GAS FRYERS BASIC FRYING INSTRUCTIONS • Set the desired temperature and allow shortening to heat up to that temperature. • Fry items that are about the same size together to ensure equal doneness. • Drain or wipe dry raw or wet foods to minimize splatter when lowering into the hot shortening.
— 15 — GR SERIES GAS FRYERS DAILY FILTERING – ALL MODELS WARNING: HOT OIL AND HOT PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE FRYER. WARNING: WHEN HANDLING HOT OIL, WEAR INSULATED AND OIL- PROOF GLOVES. • Filter shortening at least once a day.
— 16 — GR SERIES GAS FRYERS BOIL OUT PROCEDURE Weekly or as required 1 . Drain the tank as described under DRAINING THE TANK. 2 . Once the shortening has been drained, flush out scraps and sediment with a small amount of warm shortening, using tank brush.
— 17 — GR SERIES GAS FRYERS MAINTENANCE WARNING: HOT OIL AND HOT PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK.
— 18 — GR SERIES GAS FRYERS TROUBLESHOOTING WARNING: FRYERS WITH KLEENSCREEN™ FILTERS: CERTAIN PROCEDURES IN THIS SECTION REQUIRE ELECTRICAL TESTS OR MEASUREMENTS WHILE POWER IS APPLIED TO THE MACHINE.
— 19 — GR SERIES GAS FRYERS.
F-31233 Rev. B (May 2006) PRINTED IN U.S.A ..
An important point after buying a device Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410, (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410, yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410, - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410, you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410, will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410,, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410,.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410,. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart 1GR35M, 1GR45M, 1GR65M, 1GR85M, 2GR45MF, 2GR65MR, 2GR85MF, 3GR45MF, 3GR65MF, 3GR85MF, 4GR45MF, ML-136407, ML-136408, ML-136409, ML-136410, along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
