Instruction/ maintenance manual of the product 632 Taylor
Go to page of 50
Model 6 32 Co mbo F reezer Original Ope rating Ins tructions 030049 - - M 3/00 (Or igi nal Publ icat ion) (Updat ed 8/10/ 12).
Com plete this pa ge for quick r efer ence w hen ser vice is r equir ed: Taylor Distributor: Address: Phone: Serv ice: Par ts: Date of Installation: Infor mati on found on the data la bel: Model Numbe.
Model 6 32 T able of Cont ents T able of Contents Section 1 T o the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 ..............................
T able of Cont ents Model 63 2 T able of C ontents - - Page 2 Section 6 Operating Pr ocedu res 15 ..................................... Prior T o Set - - Up For Units With A Syrup Rai l (Optional Feature) 15 ............. Freezing Cylinder Assembl y - - Soft S erve Side 15 .
1 Model 6 32 T o th e Installer 1 10421 Section 1 T o th e Installer The f ollowing are general inst allation inst ruct ions. For complet e inst allation det ails, please see the check out card.
2 T o th e Installer Model 6 32 1 10407 Air Cooled Units DO NOT obst ruc t air int ake and dis charge openings: Air cooled units r equire a minimum of 3” (76 mm) of clearanc e around all s ides of the f reezer t o allow for adequate air flow ac ross t he condens ers.
3 Mode l 63 2 T o th e Installer 120810 S Stat ionary appliances whic h are not equipped with a power cord and a plug or another dev ice t o disconnect t he appliance fr om the power sourc e must have an all- pole disconnect ing devic e with a cont act gap of at least 3 m m inst alled in the ext ernal installat ion.
4 T o th e Operator Model 6 32 0 8 111 7 Sec tion 2 T o the Ope rator The f reezer you hav e pur chased has been car efully engineered and manuf act ured t o give y ou dependable operat ion. T he T aylor Model 632, when properly operat ed and cared f or , will produc e a consist ent quality produc t.
5 Mode l 63 2 Safety 1 10407 Se cti on 3 Sa fety We, at T aylor Company , are concerned about t he safet y of the operat or when he or s he comes in cont act with t he fr eezer and its par ts . T aylor has gone to extr eme effor ts to des ign and manuf actur e built- - in safet y f eatur es t o protec t bot h you and the service technic ian.
6 Safety M odel 6 32 0 8 111 7 S DO NOT allow unt rained pers onnel to operat e this m achine. S DO NOT operat e t he freez er unless all serv ice panels and access doors ar e restrain ed with screw s. S DO NOT rem ove any int ernal oper ating part s (examples: f reez er door , beat er , scr aper blades, et c.
7 Mo del 632 Op erato r Parts I den ti fi cati on 1111 0 1 Section 4 Operator Parts Identif ication Model 632 E xploded View.
8 Op erato r Parts I den ti fi cati on Mode l 63 2 1111 0 1 Model 632 P ar ts Identif ication Li st ITE M DESCRIPTI ON PART NO. 1 COVER-HOPPER 053809 2 TUBE-FEED- SHAKE-5/ 16 HOLE 028967-7 3 TUBE A.- FEED-SS- 5/32 HOLE X29429-2 4 OR IFIC E 022465-100 5 O-RI NG-3/8 OD X .
9 Mo del 632 Op erato r Parts I den ti fi catio n Soft S erve D oor Assem bly E xploded View Item Descripti on Part No. 1 Seal- - Drive Shaft 032560 2 Shaft- - Beater 032564 3 Beater A.
10 Op erato r Parts I den ti fi catio n Model 6 32 Shake Door A ssembly E xploded View Item Descripti on Part No. 1 Seal- - Drive Shaft 032560 2 Shaft- - Beater 032790 3 Beater A.- - 7 Qt.- - 1 Pin X46233 4 Cli p - - Scraper Blade - - 8.75” 046238 5 Blade- - Scraper- - Plasti c 046237 6 Beari ng - - Front 0131 16 Item Descripti on Part No.
11 Mo del 632 Op erato r Parts I den ti fi catio n Accessor ies Item Descripti on Part No. 1 Brush- - Rear Bearing 013071 2 Brush- - Double Ended 013072 3 Brush- - Draw V alve 014753 4 Brush- - Mix Hopper 023316 5 Lubri cant- - T aylor 4 oz. 047518 6 Pail- - Mix 10 qt.
12 Impor tant : T o the Opera tor Model 6 32 Section 5 Important: T o the Operator Item Descripti on 1 Power Swit ch 2 Mix Low I ndicat or Light 3 Mix (Hopper Ref rigerat ion) 4 Standby 5 Wa s h 6 Aut.
13 Model 63 2 Im porta nt: T o the Oper ator Mix Ref When t he MI X REF key is pressed, t he light comes on indicating t he mix hopper re f rigerat io n syst em is operat ing. MIX REF is contr olled by the lef t side of t he fr eezer as v iewed fr om the oper ator end.
14 Impor tant : T o the Opera tor Model 6 32 Air T ube (S oft Ser ve) The air t ube serves t wo pur poses. O ne end of the t ube has a hole and t he other end does not. Figur e 1 1. Af t er priming t he mac hine, lubric ate t he o - - rings on the air t ube ( the end with the hole ) and place it into t he mix inlet hole.
15 Model 6 32 Op erati ng P roced ures 0 8 111 7 Section 6 Operating Procedures We begin our inst ruct ions at t he point where we enter the st ore in t he morning and f ind the parts disassem bled and laid out t o air dry f rom t he previous night’s cleaning.
16 Op erati ng Pro ced ures Model 6 32 Inser t t he driv e shaft int o the freez ing cylinder , hex end fir st, and into t he rear s hell bearing until t he seal f its secur ely over t he rear shell bearing. Engage t he hex end fir mly int o the dr ive coupling.
17 Model 6 32 Op erati ng P roced ures Slide the t wo o - - r ings int o the groov es on t he pr ime plug. Apply an even coat of T aylor Lube t o t he o - - rings and shaf t. Figur e 8 Inser t t he prim e plug into t he hole in the t op of the fr eezer door , and pus h down.
18 Op erati ng Pro ced ures Model 6 32 Slide the f ork over t he bar in t he slot of t he dr aw valve. Secure wit h pivot pin. Figur e 14 Note: T hese unit s f eatur e adjustable draw handles to provide t he best port ion cont rol. T he draw handles c an be adjust ed for diff erent f low rates .
19 Model 6 32 Op erati ng P roced ures Freezing C ylinder A ssembly - - Sha ke Sid e Note: W hen lubric ating part s, use an appr oved food grade lubricant (ex ample: T aylor Lube). MAKE SURE CO NTRO L SW IT CH IS I N THE “OFF ” POSITI ON. Failur e t o do so m ay c ause injury fr om hazardous mov ing parts , or elect rocut ion.
20 Op erati ng Pro ced ures Model 6 32 If blades are in good condit ion, ins tall t he scr aper blade clips on t he sc raper blades. P lace the r ear sc raper blade ov er t he rear holding pin on the beater (k nife edge to t he outs ide).
21 Model 6 32 Op erati ng P roced ures 0 8 111 7 Rotat e t he draw v alve brac ket to t he lef t and center it into posit ion by r aising the dr aw arm and plac ing it int o the slot t ed groove of t he draw valve br acket . Note: T he draw v alve brack et m ust be pos itioned wit h the n otch to th e le ft.
22 Op erati ng Pro ced ures Model 6 32 Step 4 Place t he power swit ch in t he ON pos ition. Figur e 31 Step 5 Pres s the WASH key . T his will cause the saniti zing solution in t he f reezing cy linder t o agitat e. Allow it to agitat e for fiv e minutes .
23 Model 6 32 Op erati ng P roced ures Prim ing Step 1 Wit h a pail beneath t he door spout, open t he draw handle. Be s ure t he prime plug is s till in the UP position (sof t s erve s ide only). Pour two gallons (7. 6 liter s) of fres h mix int o the mix hopper and allow it to f low into the f reezing c ylinder .
24 Op erati ng Pro ced ures Model 6 32 0 8 111 7 Closing P r ocedure T o disassem ble your unit , t he f ollowing it ems will be needed: S T wo cleaning pails S Sanitiz ed st ainless st eel rer un can.
25 Model 6 32 Op erati ng P roced ures 0 8 111 7 Re pea t ste ps 1 through 7 for t he other s ide of t he fr eezer . Disassem bly BE SU RE TH E POWER SWITC H IS IN THE OFF POSITION .
26 Impor tant : Opera tor C hec klis t Model 6 32 0 8 111 7 Section 7 Important: Operator Checklist Dur ing Cl eaning and Sani tizing AL W A YS FOLLOW LOCAL HEAL TH CODES. Clean in g and san i tiz in g sched u les are govern ed by fe der al, s ta te, or loca l re gulator y a genc ies , and mu st be f ol lo w ed acco rdi ng ly .
27 Model 6 32 Impor tant : Opera tor C hec klis t 0 8 111 7 CAUTI ON: Alw ays di sc onnec t elect rical po w er pri or t o cl eani ng t he conde nse r .
28 T roubles hooting Guide Model 6 32 Section 8 T roubleshooting G uide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 1. No product i s being dispensed wi th dr aw valve open and the machi ne in t he AUTO m ode. a. Freeze- - up in mix i nlet hole. a. Call ser vice techni cian t o adjust t he mix hopper temper atur e.
29 Model 6 32 T roubles hooting Guide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 6. The dri ve shaft is st uck in th e dri ve coupli ng. a. Rounded corners of dri ve shaft , coupli ng, or both. a. Call servi ce technici an to corr ect cause, and to replace the necessar y components.
30 Parts Rep lacemen t S ched ul e Model 6 32 Section 9 Parts Replacement Schedule P ART DESCRI PT IO N EVER Y 3M O N T H S EVER Y 6M O N T H S ANNUALL Y Drive S haft Seal X *Scr aper Blade (S oft Ser.
Section 10 Parts List 31 + Avai labl e Separat ely Model 6 32 Parts List 091215 HP - - 62 REFRIGERANT DESCRI PT IO N PART NUMBER QTY. WARR. CLASS RE MARKS PART S UPDATE ADAPTOR A.- CASTER X18915 4 103 BEARING- FRONT 050216 1 000 SOFT SERVE BEARING- FRONT 013116 1 000 SHAKE BEARING- REAR SHELL *NICK.
+ Avai labl e Separat ely 32 Parts List Model 6 32 DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER COMPRESSOR M63B203BBCB-BRI STOL 062274-27 1 512 S/N K7045455 & UP / 208-230/ 60/.
33 + Avai labl e Separat ely Model 6 32 Parts List DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER CONDENSER-AC- 7X6X1.25- 2 ROW 027155 1 103 SHR COUPLING- DRIVE 1/2 SQ. X 1-7/ 8 025997 1 103 SHAKE COUPLING- DRIVE 3/4 HEX X 1- 7/8 012721 1 103 SOFT SERVE COVER-HOPPER * GRAY* 053809 2 103 DECAL-CLEAN I NST.
+ Avai labl e Separat ely 34 Parts List Model 6 32 DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER GUIDE A. -DRI P PAN *632* X28929 2 103 HOOD * 632* 049771-SP * 103 K9083225 & Pr ior - 5/ 17/96 To 5/ 19/09 ( ECN 109570) KIT A. -COMPRESSOR-DANFOSS X47701SER2 1 512 +DRYER-CAP.
35 + Avai labl e Separat ely Model 6 32 Parts List DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER LUBRICANT- TAYLOR 4 OZ. 047518 1 000 MAN-OPER 632 030049-M 1 000 MOTOR-1.0 HP 013102-27 1 212 208- 230V 60HZ 1PH - SHAKE MOTOR-1.5 HP 021522-27 1 212 208- 230V 60HZ 1PH - SS MOTOR-1.
+ Avai labl e Separat ely 36 Parts List Model 6 32 DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER PULLEY-AK74 051013 1 103 GEAR - SHAKE RECEPTACLE A.
37 + Avai labl e Separat ely Model 6 32 Parts List DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER BRACKET A.- SWITCH X51682 1 103 J7061461/UP 118 BRACKET A.- SWITCH X33330 1 103 (OLD STYLE) 118 E-RI NG EXTERNAL 1/2 024908 2 000 SCREW-4- 40 X 5/8 RHM- ZP STEEL 027219 2 000 SPRING- RETURN L.
+ Avai labl e Separat ely 38 Parts List Model 6 32 DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER SWITCH- PRESSURE 350 PSI 048231 2 103 TRAY-DRI P 22-13/ 16 X 5-1/8 046171 1 103 VALV.
39 + Avai labl e Separat ely Model 6 32 Parts List DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER MOTOR-1. 5 HP CAPS@10&2 O'CLO 021522-34 1 212 220- 240V 50HZ 1PH PANEL A.- FRONT *632* SYR*HP62 X49747 1 103 220-240V 50HZ 3PH W/SY RAI L PANEL A.
+ Avai labl e Separat ely 40 Parts List Model 6 32 DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER OPTIONA L COVER-LI FT OFF W/PLAI N KNOB 028772 2 103 FAUCET-CENTRAL 4 I N. CENT 016778 1 103 +PLATE-FAUCET 016796 1 103 HOOD *632* W/ FAUCET HOLES 049771- SP1 1 103 FOR FAUCET OPTION JAR-3 QT.
41 + Avai labl e Separat ely Model 6 32 Parts List DESCRI PT IO N PARTS UPDATE REMARKS WARR. CLASS QTY. PART NUMBER FILTER- CORCOM 2VR1 032567 1 103 HOOK-UPPER SPI NNER 011173 1 103 MOTOR- SPINNER MODEL 22- 230 020101-27 1 103 PLATE A.- SWITCH * SPINNER A.
Mode l 63 2 049443-27 2/12.
Mode l 63 2 049443-33 2/12.
Mode l 63 2 049443-35 2/12.
Mode l 63 2 049443-40 2/12.
Mode l 63 2 049443-58 2/12.
An important point after buying a device Taylor 632 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Taylor 632 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Taylor 632 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Taylor 632 you will learn all the available features of the product, as well as information on its operation. The information that you get Taylor 632 will certainly help you make a decision on the purchase.
If you already are a holder of Taylor 632, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Taylor 632.
However, one of the most important roles played by the user manual is to help in solving problems with Taylor 632. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Taylor 632 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
