Instruction/ maintenance manual of the product 430 TORQUE Taylor
Go to page of 37
Model 4 30 T orque Sh ake/S lush F reezer Original Ope ra ting Instructions 051430 - M 3/97 (Or i ginal Publ icat ion) (Up da ted 7 /3 /12 ).
Com plete this pa ge for quic k refe renc e when ser vic e is re quir ed: Taylor Distributor: Address: Phone: Serv ice: Par ts: Date of Installation: Infor mati on found on data plat e: Model Number: .
T able of Cont ent s Model 4 30 T or que T able of Contents Section 1 T o the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 ....................
Mode l 430 T orque T able of C ontent s T able of C ontents - - Page 2 ______________________________________________________________________________ Se ction 7 Impor tant: Opera tor Check list 18 .............................. During Cl eaning and Saniti zing: 18 .
1 Model 4 30 T orque T o th e Installer 0901 14 Section 1 T o t he Installer The f ollowing are general inst allation inst ruct ions. For complet e inst allation det ails, pleas e see the c heck out card. Installer Safety In all ar eas of t he world, equipment should be installed i n acc ordance wit h existing local codes.
2 T o th e Installer Model 430 T orque 101012 Air Cooled Units DO NOT obst ruc t air int ake and disc harge openings: Air c ooled units r equire a minimum of 3” (76. 2 mm) of clearanc e around all sides of the f reezer t o allow f or adequate air f low acros s condenser.
3 Mode l 430 T orque T o th e Installer 120709 Beater Rotation Beater rot ation mus t be cloc kwise as viewed looking into t he f reezing cy linder . Note : The following proce dure m ust be perf ormed by an aut ho riz ed T ayl o r service tech ni cian .
4 T o th e Operator Mode l 430 T orque 061012 Sec tion 2 T o the Opera tor The f reezer you have pur chased has been carefully engineered and manuf act ured to giv e you dependable operat ion. The T aylor Model 430 T orque, when properly operated and c ared for, will pr oduce a consist ent qualit y product.
5 Mode l 430 T orque Safety 1 10414 Se cti on 3 Sa fety We at T aylor Company ar e c oncerned about t he safet y of the operator when he or she comes in contact wit h the f reezer and it s par ts. T aylor has gone to ext reme effort s t o design and manufac tur e built - - in saf ety feat ures t o prot ect bot h you and t he serv ice technician.
6 Safety M odel 43 0 T orque 0901 14 S DO NOT allow unt rained pers onnel to operat e this m achine. S DO NOT operat e t he freez er unless all serv ice panels and access doors ar e restrain ed with screw s. S DO NOT rem ove any int ernal operat ing part s (examples: f reezer door, beater , scr aper blades, et c.
7 Model 43 0 T orque Oper at or Par ts Ide ntific ation 070104 Section 4 Operator Parts Identif ication AUTO OFF WASH 1 6 12 7 8 10 11 2 3 4 5 9 Item Descripti on Part Numb er 1 Sh ield - - S pla sh 049320 2 Tra y - - Dri p 049319 3 Pan- - Drip 17- - 1/4” Long 027504 4 Gasket- - Base Pan 049420 5 Panel A.
8 Oper at or Par ts Ide ntific ation Mode l 430 T orque 1 11018 Item Descripti on Part Numb er 1 Door A.- - Parti al- - Prime X50403- - SER 2 Handle A.- - Draw X47384 3 Va l v e - - D r a w 047734 4 V alve A.- - Handle Pin X25929 5 O- - Ring - - 1” OD x .
9 Model 43 0 T orque Oper at or Par ts Ide ntific ation Item Descripti on Part Numb er 1 Brush- - 3” x 7” Whit e 023316 2 Brush- - Double Ended 013072 3 Brush- - Draw V alve 014753 Item Descripti on Part Numb er 4 Brush- - Rear Beari ng 013071 5 Lubri cant- - T aylor 047518 *6 V ideo- - Tr aini ng M430T orque 050987- - V *Not Shown.
10 Impor ta nt: T o the Opera tor Model 4 30 T orque Section 5 Important: T o the Operator Viscosity Adjustment The viscosity (thickn ess) of the slush can be adjusted by t urning the v iscosit y adjus tment sc rew on t he upper right s ide of t he front panel.
11 Mo del 430 T o rqu e Op erati ng Pro cedu res Section 6 Operating Procedures The M odel 430 freez er is designed t o produce s hake or slush product at t he desired thic kness.
12 Op erati ng Pro cedu res Mo del 430 T o rqu e Holding the beat er sec urely , slide t he beater int o the fr eezing cylinder and align the hole at t he rear of the beater with t he flat s on t he end of t he drive shaf t . Slide the beat er t he remainder of t he way int o the fr eezing cylinder and ov er the end of t he drive s haft .
13 Mo del 430 T o rqu e Op erati ng Pro cedu res Ro tate th e dr aw va lv e so the fl ats o n the to p of the draw valve ar e perpendicular t o the door fac e. Figur e 12 Ins ert t he ice bust er t hrough the door spout and into the slot locat ed just above t he lower o - - ring.
14 Op erati ng Pro cedu res Mo del 430 T o rqu e 0901 14 Step 7 Inst all t he front drip pan. Slide t he long drip pan into the hole in the f ront panel. Figur e 17 Step 8 Inst all t he front drip t ray and s plash shield beneat h the door spout . Figur e 18 Step 9 Lay t he air/m ix feed t ube (opt ional) in t he bott om of the mix hopper .
15 Mo del 430 T o rqu e Op erati ng Pro cedu res Step 5 Place an em pty m ix pail beneath the door spout and move t he draw handle t o t he right . Draw off all the saniti zing solut ion. W hen the sanit izer stops flowing fr om the door s pout, m ove t he draw handle to t he left and place the c ontr ol switc h in the “O FF ” pos ition.
16 Op erati ng Pro cedu res Mo del 430 T o rqu e Step 4 Place t he mix hopper cover in posit ion. Periodically , during t he day’s operation, check t o be sure t here is a subst antial am ount of mix in t he hopper .
17 Mo del 430 T o rqu e Op erati ng Pro cedu res 0901 14 Cleaning Step 1 Prepar e a pail of an approv ed 100 P PM cleaning solution (ex amples: 2 - - 1/2 gal. [9. 5 liters ] of Kay - - 5 R or 2 gal. [7.6 liters ] of Ster a- - S heen R ). USE W ARM W A TE R AND F OLLO W T HE MANUFACTURER’S SPECIFICA TI ONS.
18 Impor ta nt: Oper ator C hec klis t Model 43 0 T orque 071205 Section 7 Important: Operator Checklist Dur ing Cleani ng and Sani tizing: AL W A YS FOLLOW LOCAL HEAL TH CODES Clean in g and san it iz in g sched ul es are govern ed by fed eral, state, o r l ocal reg ul ato ry agen cies, an d must be f ol lo wed acco rdi ng ly .
19 Model 43 0 T orque Impor ta nt: Oper ator C hec klis t Winter Stor age If the place of bus iness is to be closed dur ing t he winter mont hs, it is import ant to prot ect the freezer by following cert ain prec autions, par ticular ly if t he building is t o be left unheated and s ubject t o fr eezing conditi ons.
20 T roubles hooting Guide Model 4 30 T orque Section 8 T roubleshooting Guide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 1. No product being dispensed. a. Power s witch is in the “O F F” position. a. Place power switc h in the “AUTO ” position.
21 Model 4 30 T orque T roubles hooting Guide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 5. Product t oo thin. a. Missing, in correctly in stalled , or bad scraper blade. a. Ins tall or r eplace scr aper blade. 11 b. Im proper mix ing of pr oduct. b.
22 Parts Rep lacemen t Sch edu l e Mo del 430 T o rqu e Section 9 Parts Replacement Schedule P ART DESCRI PT IO N EVER Y 3 MONT HS EVER Y 6 MONT HS ANNUALL Y QUANT I TI ES TO BE REPL ACED Drive S haft.
Section 10 Parts List 23 + A vail able Separ atel y Model 4 30 T orque Parts List 120703 DESCRI PTI ON P ART NUMBER QTY. WARR. CLASS RE MARKS P ART S UPDA TE 043012H555 TORQUE - 115V 60HZ 1PH & 04.
+ A vail able Separ atel y 24 Parts List Model 43 0 T orque DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER CORD-POW ER-230V 15A PLUG- 75"L 025340-27 1 103 208- 230V 60HZ 1PH COVER A.- BLACK INS. MIX HOPPER X49679-BLA 1 103 COVER-HOLE- DRAW HANDLE *430* 050499 1 103 DECAL-DEC- 430 - TORQUE 050685 1 000 DECAL-CLEAN I NST.
25 + A vail able Separ atel y Model 4 30 T orque Parts List DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER GASKET-DOOR 5. 109"I D X 5.630OD 014030 1 000 O-RI NG 1 'OD X .139W 032504 2 000 DRAW VALVE O-RI NG-. 291 ID X . 080W 018550 1 000 TORQUE O-RI NG-7/ 8 OD X .
+ A vail able Separ atel y 26 Parts List Model 43 0 T orque DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER P R O B EA . - M I XL O W X42077 1 103 MIX LOW P R O B EA .
27 + A vail able Separ atel y Model 4 30 T orque Parts List DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER BUSHING A. -TORQUE X50399-SER 1 103 BUSHING- ARM-TORQUE 049737 1 103 BUSHING- PIVOT- TORQUE ARM 049739 1 103 NUT-PUSH ON-9/ 16DIA.
+ A vail able Separ atel y 28 Parts List Model 43 0 T orque DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER 043027HA55 - 208-230V 60HZ 1PH - MARINE-TOR QUE CONTROL DIAGRAM- WIRI NG* .
29 + A vail able Separ atel y Model 4 30 T orque Parts List DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER 043012H210 - 115V 60HZ 1PH - PANEL SPIN- RIGHT SI DE-HARD SLUSH LEG-4" 3/ 8-16 STUD 036397 4 103 PANEL A.- FRONT *430* TORQU X50897 1 103 PLUG-HOLE 1/ 4 DIA.
+ A vail able Separ atel y 30 Parts List Model 43 0 T orque DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER + FAN-5 BLADE 7 " PUSH 30D 016289 1 103 220-240V 50HZ 1PH PANEL-BACK * 430* 063937 1 103 220-240V 50HZ 1PH RELAY-3 POLE- 20A-208/ 240 066795-33 1 103 220- 240V 50HZ 1PH STARTER-1 PHASE 2.
31 + A vail able Separ atel y Model 4 30 T orque Parts List DESCRI PTI ON P ARTS UPDA TE REMARKS WARR. CLASS QTY. PART NUMBER LUBRICANT- TAYLOR 4 OZ. 047518 1 000 MAN-OPER 430 DUNKI N DONUT 051430DD 1 000 PAIL- MIX 10 QT. 013163 1 000 PAIL- MIX 10 QT.
Model 430 T orque 050367- - 12 7/3/ 12.
Model 430 T orque 050367-27 7/3/ 12.
An important point after buying a device Taylor 430 TORQUE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Taylor 430 TORQUE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Taylor 430 TORQUE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Taylor 430 TORQUE you will learn all the available features of the product, as well as information on its operation. The information that you get Taylor 430 TORQUE will certainly help you make a decision on the purchase.
If you already are a holder of Taylor 430 TORQUE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Taylor 430 TORQUE.
However, one of the most important roles played by the user manual is to help in solving problems with Taylor 430 TORQUE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Taylor 430 TORQUE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
