Instruction/ maintenance manual of the product PFSY92080 ProForm
Go to page of 28
¨ USERÕS MANUAL Model No. PFSY92080 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 ASSEMBLED DIMENSIONS: Height: 79 in. Width: 38 in. Length: 91 in. Low Pulley Station Foot Plate Leg Lever Butterfly Arms Press Arm Shroud Covering Weight Stack Seat Backrest Thank you for selecting the versatile PROFORM ¨ 920 Home Gym System.
4 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual.
1. Before beginning, make sure that you have read and understood the information on page 4. Locate and open the parts bag labeled ÒFRAME ASSEMBL Y . Ó Press a 2Ó Square Inner Cap (24) into each end of the Stabilizer (5). Insert two 3/8Ó x 2 3/4Ó Carriage Bolts (20) up through the holes in the Stabilizer and place it flat on the floor .
5. Slide the Press Upright (3) onto the indicated 5/16Ó x 2 1/2Ó Carriage Bolts (22) in the Press Base (4). T ighten a 5/16Ó Nylon Locknut (68) onto each Carriage Bolt. Note: The Press Upright (3) must be leaning towards the center of the unit with the two brackets oriented as shown.
7. Position two W eight Bumpers (19) over the indicated holes in the Stabilizer (5). Insert both Weight Guides (23) through the Weight Bumpers (19) and the holes in the Stabilizer (5 ). See the inset drawing. Press two Round Weight Inserts (76) into the indicated holes in each Weight (26).
8 13. Press Arm AssemblyÑLocate and open the parts bag labeled ÒARM ASSEMBL Y .Ó Press a 2Ó Square Inner Cap (24) into the top of each arm on the Press Frame (12). Lubricate the 1/2Ó x 9 1/2Ó Bolt (59). Slide the Cable Frame (57) in between the arms of the Press Frame (12).
9 16. Butterfly Arm Assembly Press a 2Ó Square Inner Cap (24) into both ends of each Butterfly Arm (80 and 81). Wet the lower end of each Arm with soapy water . Slide a Butterfly Foam Pad (82) onto the lower end of each Arm. 16 14. Press a 2Ó Square Inner Cap (24) into the lower end of each Press Arm (46 and 47).
17 17. Lubricate both axles on the T op Frame (1). Identify the Right Arm (80) and the Left Arm (81) by noting the position of the welded bracket (A) on each Arm. Arm identification is very important for this step. Place a Weld Cover (63) on top of the Right Butterfly Arm (80) in the location shown.
11 22. Remove the 3/8Ó Nylon Jamnut (78) attached to the 3/8Ó x 5Ó Bolt (42) in step 20. Wrap the High Cable (73) around a 3 1/2Ó Pulley (35) in the direction shown. Slide the 3 1/2Ó Pulley (35) and a Cable T rap (44) onto the 3/8Ó x 5Ó Bolt (42) that was inserted into the welded tube on the Cable Frame (57) in step 20.
12 25. Wrap the High Cable (73) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the 3 1/2Ó Pulley (35) to the bracket on the T op Frame (1) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (50). 25 1 62 73 50 Bracket 35 26. Thread the bolt at the end of the High Cable (73) a couple of turns into the top of the Weight Tube (77).
13 28. Dis-assemble the second set of Pulley Plates (31). Wrap the Butterfly Cable (97) around one of the 3 1/2Ó Pulleys (35) in the direction shown. Attach the 3 1/2Ó Pulley (35) and a Cable T rap (44) to the Pulley Plates (31) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (50).
14 32. Wrap the Low Cable (72) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley (35) and a Cable T rap (44) to the lowest of the two holes in the Pulley Plates (31) hang- ing from the High Cable (73). Secure the Pulley and Cable T rap with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (50).
15 36. Important: Follow all three Cables from end to end and make sure they rest in the grooves of all Pulleys and that both the Cables and the Pulleys move smoothly . Unscrew the cable bolt at the end of the High Cable (73) from the Weight Tube (77).
16 38. Attach one Backrest (41) to the Butterfly Backrest Frame (15) with two 1/4Ó x 3/4Ó Screws (17). Unscrew the handle on the Adjustment Knob (99) until it is loose. Pull out the handle as far as it will go and slide the Butterfly Backrest Frame (15) into the slot in the Butterfly Upright (2).
17 41. Press two 3/4Ó Round Inner Caps (34) into each Pad T ube (28). Insert one Pad T ube (28) into the Butterfly Seat Frame (1 1). Slide a Foam Roller (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Roller (30) onto each end of the Pad T ube.
18 44 44. The decal shown below has been attached to the home gym system in the two locations shown. If a decal is missing or illegible, please call our customer hotline at the number on the front cover to order a replacement decal. Apply the new decal in the appropriate location.
19 Cable Diagram The Cable Diagrams below show the proper routing of the Butterfly Cable (97), the High Cable (73) and the Low Cable (72). The numbers show the correct route for each cable. Make sure the Cables are routed correctly , that the Pulleys move smoothly and that the Cable T raps do not touch or bind the Cables.
20 Attaching the Lat Bar or Row Bar to the High Pulley Station Attach the Lat Bar (61) to the High Cable (73) with a Cable Clip (69). For some exercises, the Chain (67) should be attached between the Lat Bar and the High Cable with two Cable Clips.
Adjusting the Position of the Press Backrest for Row Exercises Unscrew the handle on the Adjustment Knob (99) until it is loose. Pull out the handle as far as it will go and tilt the Press Backrest (41) in or out to the desired position.
22 Arm Press Lower Pulley Upper Butterfly Weight Row Leg Ext. Pulley Arms Plates (lbs.) (lbs.) (lbs.) (lbs.) To p 13 7 12 6 1 29 19 21 18 2 43 30 32 32 3 57 42 45 44 4 74 52 58 56 5 87 64 68 70 6 106 .
Ordering Replacement Parts Limited W arranty T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
23 Additional slack can be removed by moving one or both of the 3 1/2Ó Pulleys (35) attached to one or both sets of Pulley Plates (31). T o move one Pulley , unscrew the 3/8Ó Nylon Locknut (50) and the 3/8Ó x 2Ó Bolt (62). Remove the Cable T rap (44) and Pulley (35) from the Pulley Plates (31).
1 3/4Ó Square Inner Cap (21) 3/4" Round Inner Cap (34) 3/4Ó Retaining Ring (86) 1" Round Inner Cap (88) 5/8Ó x 1/2Ó Bushing (32) 3/4Ó Dome Cap (75)Ñ2 2" Square Inner Cap (24) 1&qu.
3/8" Nylon Locknut (50) 3/8" Nylon Jam Nut (78) 5/16" Nylon Jamnut (25) 5/16" x 2 1/2" Bolt (45) 5/16" Nylon Locknut (68) #8 x 1Ó Black Screw (7) 1/4" x 1 3/4".
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 T op Frame 2 1 Butterfly Upright 3 1 Press Upright 4 1 Press Base 5 1 Stabilizer 6 1 Leg Lever Bu.
32 32 78 55 74 55 68 45 17 6 7 17 11 29 13 41 15 17 17 2 68 68 22 22 68 68 8 24 68 68 50 18 3 38 24 22 22 4 78 55 54 55 35 47 46 1 18 50 50 24 24 42 35 35 50 85 79 50 62 35 31 35 50 62 44 62 48 35 68 .
An important point after buying a device ProForm PFSY92080 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ProForm PFSY92080 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ProForm PFSY92080 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ProForm PFSY92080 you will learn all the available features of the product, as well as information on its operation. The information that you get ProForm PFSY92080 will certainly help you make a decision on the purchase.
If you already are a holder of ProForm PFSY92080, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ProForm PFSY92080.
However, one of the most important roles played by the user manual is to help in solving problems with ProForm PFSY92080. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ProForm PFSY92080 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
