EN
Procom logo
Official user manual

Procom SFE33RE-C

11 pages·2.1 MB·Indoor Fireplace·PDF·ENDEFRITNLJA
Procom SFE33RE-C
Table of Contents 60 sections PRO-COM · SFE23RE-W SFE23RE-C SFE23RE-O · SFE33RE-W SFE33RE-C SFE33RE-O · SFE23RE-DO · … ShowHide
PRO-COMp.1SFE23RE-W SFE23RE-C SFE23RE-Op.1SFE33RE-W SFE33RE-C SFE33RE-Op.1SFE23RE-DOp.1SFE33RE-DOp.1Freestanding Electric Fireplacep.1SFE23RE SHOWNp.1Installation Instructions and Owner’s Manualp.1FOR YOUR SAFETYp.1IN THE VICINITY OF THIS OR ANYp.1OTHER APPLIANCEp.1PC-FE23A610-0506p.1TABLE OF CONTENTSp.2PLEASE READ THE INSTALLATION & OPERATION INSTRUCTIONSp.2BEFORE USING THIS APPLIANCEp.2Important Instructions ….…………………………………………………………....2p.2IMPORTANT INSTRUCTIONSp.3LOCATING YOUR ELECTRIC FIREPLACEp.4WARNING: Electrical outlet wir-p.4ing must comply with local build-p.4ing codes and all other appliablep.4regulations to reduce the risk ofp.4WARNING: Do not use this fire-p.4CLEARANCE TO COMBUSTIBLESp.4place if any part of it has beenp.4under water. Immediatly call ap.4quilified service technitian to in-p.4spect the fireplace and replacep.4any part of the electrical systemp.4ELECTRICAL CONNECTIONp.4ELECTRICAL SPECIFICATIONSp.4SERVICE INSTRUCTIONSp.4REPLACING LIGHT BULBSp.4MAINTENANCE OF MOTORSp.5GLASS INFORMATIONp.5ELECTRICAL WIRING DIAGRAMp.5Wire Gauge:p.5Power Cord 14AWGp.5Heater Element 16AWGp.5Other Wire 18AWGp.5Operating Instructionsp.6SPECIFICATIONS:p.8Replacement Partsp.8Replacement Parts Listp.9SFE23RE-X* SFE33RE-X*p.9* -X represents -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)p.9* -X specify -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)p.9when orderingp.9Installing decorating logsp.10Installing logs for SFE23RE:p.10Installing logs for SFE33RE:p.10FIG 1 - Logs for SFE23REp.10FIG 5 - Logs for SFE33REp.10FIG 2p.10FIG 6p.10FIG 3p.10FIG 7p.10FIG 8p.10FIG 4p.10FIG 9p.10
Page 1 of the Procom SFE33RE-C user manual — PC-FE23A610-0506
Page 1 · click to enlarge
Page 1

PRO-COM

SFE23RE-W SFE23RE-C SFE23RE-O

SFE33RE-W SFE33RE-C SFE33RE-O

SFE23RE-DO

SFE33RE-DO

Freestanding Electric Fireplace

SFE23RE SHOWN

Installation Instructions and Owner’s Manual

MAY RESULT CAUSING PROPERTY, PERSONAL INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY

Procom SFE33RE-C — FOR YOUR SAFETY diagram (page 1)
Fig. 1

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS

IN THE VICINITY OF THIS OR ANY

OTHER APPLIANCE

ANSI/UL1278. MOVABLE AND WALL-OR CEILING HUNG ELECTRIC ROOM HEATERS INSTALLER: DO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER

PC-FE23A610-0506

Page 2 of the Procom SFE33RE-C user manual — Table of Contents
Page 2 · Contents
Contents

Contents

PRO-COMp.1SFE23RE-W SFE23RE-C SFE23RE-Op.1SFE33RE-W SFE33RE-C SFE33RE-Op.1SFE23RE-DOp.1SFE33RE-DOp.1Freestanding Electric Fireplacep.1SFE23RE SHOWNp.1Installation Instructions and Owner’s Manualp.1FOR YOUR SAFETYp.1IN THE VICINITY OF THIS OR ANYp.1OTHER APPLIANCEp.1PC-FE23A610-0506p.1TABLE OF CONTENTSp.2PLEASE READ THE INSTALLATION & OPERATION INSTRUCTIONSp.2BEFORE USING THIS APPLIANCEp.2Important Instructions ….…………………………………………………………....2p.2IMPORTANT INSTRUCTIONSp.3LOCATING YOUR ELECTRIC FIREPLACEp.4WARNING: Electrical outlet wir-p.4ing must comply with local build-p.4ing codes and all other appliablep.4regulations to reduce the risk ofp.4WARNING: Do not use this fire-p.4CLEARANCE TO COMBUSTIBLESp.4place if any part of it has beenp.4under water. Immediatly call ap.4quilified service technitian to in-p.4spect the fireplace and replacep.4any part of the electrical systemp.4ELECTRICAL CONNECTIONp.4ELECTRICAL SPECIFICATIONSp.4SERVICE INSTRUCTIONSp.4REPLACING LIGHT BULBSp.4MAINTENANCE OF MOTORSp.5GLASS INFORMATIONp.5ELECTRICAL WIRING DIAGRAMp.5Wire Gauge:p.5Power Cord 14AWGp.5Heater Element 16AWGp.5Other Wire 18AWGp.5Operating Instructionsp.6SPECIFICATIONS:p.8Replacement Partsp.8Replacement Parts Listp.9SFE23RE-X* SFE33RE-X*p.9* -X represents -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)p.9* -X specify -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)p.9when orderingp.9Installing decorating logsp.10Installing logs for SFE23RE:p.10Installing logs for SFE33RE:p.10FIG 1 - Logs for SFE23REp.10FIG 5 - Logs for SFE33REp.10FIG 2p.10FIG 6p.10FIG 3p.10FIG 7p.10FIG 8p.10FIG 4p.10FIG 9p.10
Page 3 of the Procom SFE33RE-C user manual — IMPORTANT INSTRUCTIONS
Page 3 · click to enlarge
Page 3

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions

11. To disconnect heater, turn controls to OFF, then

should always be followed to reduce the risk of fire,

remove plug from outlet.

electric shock, and injury to persons, including the

12. Connect to properly grounded outlets only.

following:

13. When this appliance is installed, it must be electri-
1. Read all instructions before using this heater.

cally grounded in accordance with local codes with

2. This appliance is hot when in use. To avoid

the current CSA C22.1 Canadian local codes for

burns, do not come in contact with heater. Keep

USA installations. Follow local codes and National

combustible materials, such as furniture,

Electrical Code, ANSI/NFPA NO.70 and Canadian

pillows, bedding, papers, clothes, and curtains

Cord: CZ 22.2 NO.0.

at least 3 feet(1m.) from the front of the heater.

14. Do not insert or allow foreign objects to enter any
3. Extreme caution is necessary when any heater

ventilation or exhaust opening as this may cause

is used by or near children or invalids and when-

electric shock, fire or damage to the heater.

ever the heater is left operating and unattended.

15. To prevent a possible fire, do not block air intakes
4. Always unplug heater when not in use.

or exhaust in any manner. Do not use on soft

5. Do not operate any heater with a damaged cord

surfaces, such as a bed, where openings may

or plug or after the heater malfunctions, has

become blocked.

been dropped or damaged in any manner.

16. This heater gets hot and it contains internal parts
6. Any repairs to this appliance should be carried

that sparks and arcs. Do not use it in areas where

out by a qualified service person.

gasoline, paint, or flammable liquids are used or

7. Under no circumstances should this electric fire-

stored.

place be modified. Parts having to be removed

17. Use this heater only as described in this manual.

for servicing must be replaced prior to operat-

Other uses not recommended by the manufac-

ing this electric fireplace again.

turer may cause fire, electric shock, or injury.

8. Do not use outdoors.
18. Avoid the use of an extension cord because it may
9. This heater is not intended for use in bathrooms,

overheat and cause a risk of fire. However if you

laundry areas or similar indoor locations. Never

must use an extension cord, the cord shall be No.

use this appliance near a bathtub or other wa-

14AWG minimum size and rated not less than 1900

ter container.

watt. The extension cord must be a three wire cord

10. Do not run cord under carpeting. Do not cover

with grounding type plug and cord connector.

cord with throw rugs, runners or similar

19. This electric fireplace heater should not be used

coverings. Arrange cord away from traffic areas

as a drying rack for clothing. Also, do not hang

and where it will not be tripped over.

Christmas stockings or decorations on or near it. 20.SAVE THESE INSTRUCTIONS.

Page 4 of the Procom SFE33RE-C user manual — REPLACING LIGHT BULBS
Page 4 · click to enlarge
Page 4

LOCATING YOUR ELECTRIC FIREPLACE

WARNING: Electrical outlet wir-

Your new freestanding electric fireplace may be installed vir-

ing must comply with local build-

ing codes and all other appliable

tually anywhere in your home. However when choosing a

location for your new electric fireplace, ensure that the gen-

regulations to reduce the risk of

eral instructions are followed. For best effect results, install

fire, electrical shock and injury.

the electric fireplace out of direct sunlight.

WARNING: Do not use this fire-

CLEARANCE TO COMBUSTIBLES

place if any part of it has been

Sides 0 mm 0 inches

under water. Immediatly call a

Floor 0 mm 0 inches

quilified service technitian to in-

spect the fireplace and replace

Top 0 mm 0 inches

any part of the electrical system

ELECTRICAL CONNECTION

if necessary.

A 15 AMP, 120 Volt,60Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit. Other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is on operation. The unit comes standard with a 6’ (1828mm) long three wire cord exiting from the rear of the fireplace. Plan the installation to avoid the use of an extension cord. If an extention cord must be used, it must be a minumum 14 AWG three wire with grounding type plug connector and rated no less than 1900 Watts.The cord shall not be more than 20 feet in length.

ELECTRICAL SPECIFICATIONS

Voltage120 VAC, 60 Hz
Total Amps11.5 Amps
Total Watts1380 Watts
Heater Rating1200 Watts

SERVICE INSTRUCTIONS

4. Remove the four screws that secure the log set/ember bed in position. 5. Remove log set / ember bed and grate assembly. 6. Examine the bulb(s) to determine which bulbs need to be replaced. 7. While holding the socket, unscrew defective bulb(s) counterclockwise. 8. Install the new light bulb(s) by holding the socket and screwing clockwise. 9. Reinstall the log set/ember bed, grate assembly and screen. Follow the above procedure in reverse order.

attempting any maintenance or clean-

ing to reduce the risk of fire, electri-

cal shock or personal injury.

REPLACING LIGHT BULBS

This fireplace uses four clear 120 Volt, 60 Watt, E- 12 socket base light bulbs (small base, chandelier candle type).The 60 Watt bulbs are located under the log set/ember bed. For convenience, if one of the bulbs burns out, it may be a good idea to re- place all of the light bulbs.

Watts per bulb. The use of

1. Turn off power to the unit by unplugging the power cord. 2. Let fireplace cool if it has been operating. 3. Remove the two screws on the top corner of screen. Pull the screen upward slightly, and then pull out.

higher rated bulbs may result

in a fire causing property

damage and personal injury.

Page 5 of the Procom SFE33RE-C user manual — Power Cord 14AWG
Page 5 · click to enlarge
Page 5

MAINTENANCE OF MOTORS

GLASS INFORMATION

The motors used on the fan and flame genera-

1. Under no circumstances should this product be

tor assembly are prelubricated for extended

operated with missing or broken glass.

bearing life and require no further lubrication.

2. Do not strike or slam the glass.

However, periodic cleaning/vacuuming of the

3. Do not use abrasive cleaners to clean the glass.

fan/heater unit is recommended.

4. Replacement glass is available from the manu-

facturer and replacement should be carried out

power is turned off before

by a qualified service person.

proceeding.

ELECTRICAL WIRING DIAGRAM

Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance

with national and local codes.

If repairing or replacing any electrical component or wiring, the original wire

routing, color coding and securing location must be followed.

Wire Gauge:

Model: SFE23RE, SFE33RE Voltage: 120 VAC, 60 Hz Total Amps: 11.5 Amps Total Watts: 1380 Watts Heater Rating: 1200 Watts

Power Cord 14AWG

Heater Element 16AWG

Other Wire 18AWG

Page 6 of the Procom SFE33RE-C user manual — Operating Instructions
Page 6 · click to enlarge
Page 6

Operating Instructions

Before programming your transmitter you must first insert three triple “AAA” batteries. Make sure the main power on/off swith is in “ON” position. 1. The Mode setting: Press the “SET” button, then the “AUTO” light will flash. Press the “SET” button again, and then the “MANUAL” light will also flash. The “AUTO” light and the “MANUAL” light will flash alternately and continuously. Next press “EN- TER” button to select the auto mode or manual mode.

a. When selecting “AUTO” mode:

Select “AUTO” and press the “ENTER” button to activate , then press the “SET” button, next the ‘Temperature’, ‘Flame’, ‘Light’, ’lamp’ sym-

bols will flash alternately. Next press the

button to select the desired

temperature setting. When the temperature setting has been selected, press the “SET” button to lock in the temperature setting, next set the following functions that appear on the transmitter. When the last function setting has been completed, press the “ENTER” button, and the symbols will stop flashing. b. When selecting “MANUAL” mode:

Select “MANUAL” and press the “ENTER” but- ton to confirm, then press the “SET” button, the ‘Flame’, ‘Light’, ‘lamp’, ‘Heating level’ sym- bols will flash alternately. The next symbol will flash automatically set the functions as they appear. When the last function setting has been completed, press the “ENTER” button, and the symbols will stop flashing.

Remote Control Front Remote Control Back

Heater Front View · button or the

Page 7 of the Procom SFE33RE-C user manual — Operating Instructions
Page 7 · click to enlarge
Page 7
2. The Clock setting : Press the “CLOCK” button, the figure shown on clock will
6. Flame Effect setting: (1) Flame speed After selecting MANUAL mode or AUTO mode, the flame symbol will flash, for slow flame effect, press

flash. Press

to set the hour. After the hour has

been set, press the “CLOCK” button again to set the minutes. After the minutes has been set, press the “CLOCK” button, the clock will indicate the set time.

button, for faster flame effect, press

button.

(2) Flame brightness Press “SET” button, when the lamp symbol flashes,

3. The Timer setting : Press the “TIMER” button, the word “TIMER” will appear on

button to decrease the flame brightness

the transmitter, next press

to adjust the time, to

button to increase the flame brightness.

add 30 minutes increments press the button again. After the timer has been set, press “TIMER” button again, the word “TIMER” will flash and the timer will return to time.

7. For Flame Effect only: Select MANUAL mode, then set the Heating level to no heating level or select AUTO mode and then set temperature to lowest setting.
4. Key-Press Lock setting (child proof):

To lock, press the “LOCK” button, there will be a

symbol, which means that the transmitter is in a lock position. To

8. Manual ON/OFF button If you can’t find your Remote Control or the Remote Control is damaged, you can use manual ON/OFF button to manual turn on/turn off your heater.

once immediately followed by pressing

the “LOCK” button .

5. Heating Level setting Select the MANUAL model and press SET to chosse the heating level setting, the “

“ symbol will flash. Then

to select full, half or no heating.

(Adaptor NOT permitted in Canada) Under CZ22.2 NO. 0 standard

Show 7 more labels / short text on this page
or · press · or · and · unlock, press · press · or
Page 8 of the Procom SFE33RE-C user manual — Replacement Parts
Page 8 · click to enlarge
Page 8

SPECIFICATIONS:

Model: SFE23RE-W (-C, -O, -DO) Voltage: 120V/60HZ Total Amps: 11.5A Total Watts: 1380W Heating Ratings: 1200W Dimensions, Inches (H x W X D)

Model: SFE33RE-W (-C, -O, -DO) Voltage: 120V/60HZ Total Amps: 11.5A Total Watts: 1380W Heating Ratings: 1200W Dimensions, Inches (H x W X D)

Fireplace 38x39 1/2x15 5/8

Fireplace 43 1/2 x 52 3/4 x 16 15/16

Carton 42 1/2x41 3/8x17 5/16

Carton HEATER28 3/4 x 35 1/2 x 17 3/4

Weight, Pounds Fireplace 98

MANTEL11 x 56 x 24 1/2

Weight, Pounds Fireplace 210

Replacement Parts

Show 7 more labels / short text on this page
Shipping 115 · Shipping 230 · 17 18 19 · 17 18 19 · 20 21 22 · (Logs for SFE33) · (Logs for SFE23)
Page 9 of the Procom SFE33RE-C user manual — * -X specify -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)
Page 9 · click to enlarge
Page 9

Replacement Parts List

SFE23RE-X* SFE33RE-X*

* -X represents -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)

Ite mP a r t D e s c r ip tio nP a r t N u m b e r S F E 2 3 R E -X *S F E 3 3 R E -X * 1L o g S e tF E 2 3 A 4 0 0F E 3 3 A 4 0 0 2C o n tro l B o xN A E Y1 1 -AN A E Y1 1 -A 3R e c e ive rN A E Y1 1 -C SN A E Y1 1 -C S 4F a n H e a te r A s s e m b lyN F H T X 1 8 6 / V B 1 7 -0 0 0 GN F H T X 1 8 6 /V - B 1 7 -0 0 0 G 5D C M o to rF E 2 3 A 3 0 4F E 2 3 A 3 0 4 6P o w e r C o rd w /Te rm in a lN F H L 0 0 8 -AN F H L 0 0 8 -A 7L ig h t B u lb S o c k e t w /W irin g A s s e m b lyF E 2 3 A 3 0 6F E 2 3 A 3 0 6 8O ve r C u rre n t P ro te c to rF E 2 3 A 3 0 5F E 2 3 A 3 0 5 9A C M o to r w /Te rm in a lV L 0 5 1 -0 1V L 0 5 1 -0 1 1 0F la m e g e n e ra to r A s s yF E 2 3 A 2 0 5F E 3 3 A 2 0 5 1 1E m b e r b e d g e n e ra to r A s s yF E 2 3 A 2 0 7F E 3 3 A 2 0 7 1 2L ig h t B u lbV L 0 5 5 -0 1V L 0 5 5 -0 1 1 3R e m o te C o n tro lN A E Y1 1 -B P RN A E Y1 1 -B P R 1 4M a n te l A s s yF E 2 3 A 5 0 0 -X *F E 3 3 A 5 0 0 -X * 1 5L o u ve r A S S YF E 2 3 A 1 0 9 -AF E 3 3 1 0 9 -A 1 6V ie w in g D o o rF E 2 3 A 1 3 0 -WF E 3 3 A 1 3 0 -W 1 7L o g 1F E 2 3 A 4 0 3F E 3 3 A 4 0 3 1 8L o g 2F E 2 3 A 4 0 4F E 3 3 A 4 0 4 1 9L o g 3F E 2 3 A 4 0 5F E 3 3 A 4 0 5 2 0L o g 4F E 3 3 A 4 0 6 2 1L o g 5F E 3 3 A 4 0 7 2 2L o g 6F E 3 3 A 4 0 8

* -X specify -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)

when ordering

Page 10 of the Procom SFE33RE-C user manual — FIG 9
Page 10 · click to enlarge
Page 10

Installing decorating logs

Installing logs for SFE23RE:

Installing logs for SFE33RE:

FIG 1 - Logs for SFE23RE

FIG 5 - Logs for SFE33RE

FIG 2

1.Insert the two pins on log 1 to the two recessed holes at the middle of grate. (See FIG 2).

FIG 6

1.Place log 1, log 2 and log 3 into the correspond- ing holes on grate. (See FIG 6).

4 1 2 3

FIG 3

FIG 7

2.Insert the pin on one end of log 2 to the recessed hole on log 1, with the other end of log 2 placed on the ember bed (where marked). (See FIG 3).

2.Insert the pin on one end of log 4 to the recessed hole on log 1, with the other end of log 4 placed where marked. (See FIG 7).

4 1 2 5 3

FIG 8

FIG 4

3.Insert the pin on one end of log 5 to the recessed hole on log 2, with the other end of log 5 placed where marked. (See FIG 8).

3.Place one end of log 3 onto the hole on grate, with the other end placed on log 1 (where marked).

(See FIG 4).

6 4 1 2 5 3

FIG 9

4.Insert the pin on log 6 to the recessed hole on log 4, and place log 6 as figure shows. (See FIG 9).

Page 11 of the Procom SFE33RE-C user manual — Installing decorating logs
Page 11 · click to enlarge
Page 11
Page 11 of the Procom SFE33RE-C user manual — Installing decorating logs

Ask about the Procom SFE33RE-C

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Procom SFE33RE-C

Be the first to ask — other owners or our team will answer.

Original document

Procom SFE33RE-C manual PDF

11 pages·2.1 MB·Indoor Fireplace·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…