EN
Procom logo
Official user manual

Procom SFE23RE

13 pages·9.7 MB·Indoor Fireplace·PDF·ENDEFRITNLJA
Procom SFE23RE
Table of Contents 45 sections SFE23RE SHOWN · Installation Instructions and Owner’s Manual · FOR YOUR SAFETY · DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS · … ShowHide
Page 1 of the Procom SFE23RE user manual — PC(220)-FE23A610-0709
Page 1 · click to enlarge
Page 1

SFE23RE SHOWN

Installation Instructions and Owner’s Manual

MAY RESULT CAUSING PROPERTY, PERSONAL INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS

IN THE VICINITY OF THIS OR ANY

OTHER APPLIANCE

INSTALLERDO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER

PC(220)-FE23A610-0709

Page 3 of the Procom SFE23RE user manual — IMPORTANT INSTRUCTIONS
Page 3 · click to enlarge
Page 3

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions

11. To disconnect heater, turn controls to OFF, then

remove plug from outlet.

should always be followed to reduce the risk of fire,

electric shock, and injury to persons, including the

12. Connect to properly grounded outlets only.

following:

13. Do not insert or allow foreign objects to enter any
1. Read all instructions before using this heater.

ventilation or exhaust opening as this may cause

2. This appliance is hot when in use. To avoid

electric shock, fire or damage to the heater.

burns, do not come in contact with heater. Keep

14. To prevent a possible fire, do not block air intakes

or exhaust in any manner. Do not use on soft

combustible materials, such as furniture,

pillows, bedding, papers, clothes, and curtains

surfaces, such as a bed, where openings may

at least 3 feet (1m.) from the front of the heater.

become blocked.

3. Extreme caution is necessary when any heater
15. This heater gets hot and it contains internal parts

is used by or near children or invalids and when-

that sparks and arcs. Do not use it in areas where

ever the heater is left operating and unattended.

gasoline, paint, or flammable liquids are used or

stored.

4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord
16. Use this heater only as described in this manual.

or plug or after the heater malfunctions, has

Other uses not recommended by the manufac-

been dropped or damaged in any manner.

turer may cause fire, electric shock, or injury.

6. Any repairs to this appliance should be carried
17. Avoid the use of an extension cord because it may

out by a qualified service person.

overheat and cause a risk of fire. However if you

must use an extension cord, the cord shall be No.

7. Under no circumstances should this electric fire-

place be modified. Parts having to be removed

1.0 mm2 minimum size and rated not less than

for servicing must be replaced prior to operat-

1900 watt. The extension cord must be a three

ing this electric fireplace again.

wire cord with grounding type plug and cord

8. Do not use outdoors.

connector.

9. This heater is not intended for use in bathrooms,
18. This electric fireplace heater should not be used

as a drying rack for clothing. Also, do not hang

laundry areas or similar indoor locations. Never

use this appliance near a bathtub or other wa-

Christmas stockings or decorations on or near it. 19.SAVE THESE INSTRUCTIONS.

ter container.

10. Do not run cord under carpeting. Do not cover

cord with throw rugs, runners or similar

coverings. Arrange cord away from traffic areas

and where it will not be tripped over.

Page 4 of the Procom SFE23RE user manual — ELECTRICAL CONNECTION
Page 4 · click to enlarge
Page 4

LOCATING YOUR ELECTRIC FIREPLACE

Your new freestanding electric fireplace may be installed vir-

tually anywhere in your home. However when choosing a

location for your new electric fireplace, ensure that the gen-

eral instructions are followed. For best effect results, install

the electric fireplace out of direct sunlight.

CLEARANCE TO COMBUSTIBLES

Sides 0 mm 0 inches

Floor 0 mm 0 inches

Top 0 mm 0 inches

ELECTRICAL CONNECTION

ELECTRICAL SPECIFICATIONS

A 10 AMP, 220 Volt, 50Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit. Other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is on operation. The unit comes standard with a 6’ (1828mm) long three wire cord exiting from the rear of the fireplace. Plan the installation to avoid the use of an extension cord. If an exten- sion cord must be used, it must be a minimum 1.0 mm2 three wire with grounding type plug connector and rated no less than 1900 Watts. The cord shall not be more than 20 feet in length.

Voltage220 VAC, 50 Hz
Total Amps6.3 Amps
Total Watts1380 Watts
Heater Rating1200 Watts
Page 5 of the Procom SFE23RE user manual — FIG 5
Page 5 · click to enlarge
Page 5

Installing decorating logs

Installing logs for SFE33RE Series:

FIG 2

1.Place log 1, log 2 and log 3 into the correspond- ing holes on grate. (See FIG 2).

FIG 1

4 1 2 5 3

4 1 2 3

FIG 4 FIG 3

2.Insert the pin on one end of log 4 to the recessed hole on log 1, with the other end of log 4 placed where marked. (See FIG 3).

3.Insert the pin on one end of log 5 to the recessed hole on log 2, with the other end of log 5 placed where marked. (See FIG 4).

6 4 1 2 5 3

FIG 5

4.Insert the pin on log 6 to the recessed hole on log 4, and place log 6 as figure shows. (See FIG 5).

Page 6 of the Procom SFE23RE user manual — bulbs may result in a fire causing
Page 6 · click to enlarge
Page 6

MAINTENANCE OF MOTORS

GLASS INFORMATION

The motors used on the fan and flame genera-

1. Under no circumstances should this product be

tor assembly are prelubricated for extended

operated with missing or broken glass.

bearing life and require no further lubrication.

2. Do not strike or slam the glass.

However, periodic cleaning/vacuuming of the

3. Do not use abrasive cleaners to clean the glass.

fan/heater unit is recommended.

4. Replacement glass is available from the manu-

facturer and replacement should be carried out

WARNING: Make sure that the

by a qualified service person.

power is turned off before

proceeding.

SERVICE INSTRUCTIONS

4. Remove the four screws that secure the log set/ember bed in position. 5. Remove log set / ember bed and grate assembly. 6. Examine the bulb(s) to determine which bulbs need to be replaced. 7. While holding the socket, unscrew defective bulb(s) counterclockwise. 8. Install the new light bulb(s) by holding the socket and screwing clockwise. 9. Reinstall the log set/ember bed, grate assembly and screen. Follow the above procedure in reverse order.

WARNING: Disconnect power before

attempting any maintenance or

cleaning to reduce the risk of fire,

electrical shock or personal injury.

REPLACING LIGHT BULBS

This fireplace uses clear 220 Volt, 60 Watt, E-14 socket base light bulbs (small base, chandelier candle type). The 60 Watt bulbs are located under the log set/ember bed. For convenience, if one of the bulbs burns out, it may be a good idea to re- place all of the light bulbs.

WARNING: Do not exceed 60 Watts

per bulb. The use of higher rated

1. Turn off power to the unit by unplugging the power cord. 2. Let fireplace cool if it has been operating. 3. Remove the two screws on the top corner of screen. Pull the screen upward slightly, and then pull out.

bulbs may result in a fire causing

property damage and personal

injury.

Page 7 of the Procom SFE23RE user manual — If repairing or replacing any electrical component or wiring, the original
Page 7 · click to enlarge
Page 7

ELECTRICAL WIRING DIAGRAM

Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in

accordance with national and local codes.

If repairing or replacing any electrical component or wiring, the original

wire routing, color coding and securing location must be followed.

Page 8 of the Procom SFE23RE user manual — If repairing or replacing any electrical component or wiring, the original
Page 8 · click to enlarge
Page 8

ELECTRICAL WIRING DIAGRAM

SFE33RE

Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in

accordance with national and local codes.

If repairing or replacing any electrical component or wiring, the original

wire routing, color coding and securing location must be followed.

Page 9 of the Procom SFE23RE user manual — Operating Instructions
Page 9 · click to enlarge
Page 9

Operating Instructions

Before programming your transmitter you must first insert two “AAA” batteries. Make sure the main power on/off switch is “ON” position.

1. The ON/OFF button:
*NoteWhen Fireplace is first operated,

the default setting will be: brightest flame, and full heating To turn on Heater, press the “ON/OFF” button. To turn off heater,press the “ON/OFF” button again.

2. Flame brightness setting:

There are three settings for flame brightness: “1”,“2”and “3 (OFF)”. Press button to decrease the flame brightness, and button to increase the flame brightness.

3. Heating level setting:

There are three settings for heating level: “HI”, “LOW”, and “OFF”. Press button to decrease the Heating level and button to increase the Heating level. If set on “HI”, two heating elements will be approximately 90°F; set on “LOW”, the set room temperature will be approximately 70°F.

Remote Control Front Remote Control Back

Press “ON/OFF” button to turn on or off the fireplace. Press “HEAT Adjust” button to control heater. Press “FLAME ” button to control the Flame brightness.

Heater Front View · Manual Operation (without · handheld remote)

Page 10 of the Procom SFE23RE user manual — SPECIFICATIONS:
Page 10 · click to enlarge
Page 10

SPECIFICATIONS:

ModelSFE23RE series
ModelSFE33RE series
Voltage220V/50HZ Total Amps: 6.3A
Voltage220V/50HZ Total Amps: 6.3A
Total Watts1380W Heating Ratings: 1200W
Total Watts1380W Heating Ratings: 1200W

Dimensions, Cm (H x W X D)

Dimensions,Cm (H x W X D)

Fireplace 96.5x100x39.7

Fireplace 110 x 134 x 43

Carton 114 x 142 x48

Show 7 more labels / short text on this page
Carton 108x105x440 · Weight, Kgs · Weight, Kgs · Fireplace 60 · Fireplace 95 · Shipping 65 · Shipping 104
Page 11 of the Procom SFE23RE user manual — SFE23RE Series
Page 11 · click to enlarge
Page 11

Replacement Parts

SFE23RE Series

Page 12 of the Procom SFE23RE user manual — SFE33RE Series
Page 12 · click to enlarge
Page 12

Replacement Parts

SFE33RE Series

15 16 17 · 18 19 20 · (Logs for SFE33RE)

Page 13 of the Procom SFE23RE user manual — For SFE23RE, -X specify-O(Oak) -C(Chery) -W(White) -DO (Dark Oak)
Page 13 · click to enlarge
Page 13
Procom SFE23RE — For SFE23RE, -X specify-O(Oak) -C(Chery) -W(White) -DO (Dark Oak) diagram (page 13)
Fig. 1 · For SFE23RE, -X specify-O(Oak) -C(Chery) -W(White) -…

For SFE23RE, -X specify-O(Oak) -C(Chery) -W(White) -DO (Dark Oak)

For SFE33RE, -X specify-O(Oak) -C(Chery) -W(White) -DO (Dark Oak)

Ask about the Procom SFE23RE

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Procom SFE23RE

Be the first to ask — other owners or our team will answer.

Original document

Procom SFE23RE manual PDF

13 pages·9.7 MB·Indoor Fireplace·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…