EN
Procom logo
Official user manual

Procom V50TYLAR-BC

13 pages·8.5 MB·Indoor Fireplace·PDF·ENDEFRITNLJA
Procom V50TYLAR-BC
Table of Contents 19 sections GENERAL · LOCATING YOUR ELECTRIC FIREPLACE · CLEARANCE TO COMBUSTIBLES · ELECTRICAL CONNECTION · … ShowHide
Page 1 of the Procom V50TYLAR-BC user manual
Page 1 · click to enlarge
Page 1
Procom V50TYLAR-BC diagram (page 1)
Fig. 1

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE

INSTALLERDO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER
Page 2 of the Procom V50TYLAR-BC user manual
Page 2 · click to enlarge
Page 2
Page 2 of the Procom V50TYLAR-BC user manual
Page 3 of the Procom V50TYLAR-BC user manual — LOCATING YOUR ELECTRIC FIREPLACE
Page 3 · click to enlarge
Page 3

GENERAL

1. Read all instructions before using this
13. Do not insert or allow foreign objects to enter any

appliance.

ventilation or exhaust opening as this may cause

2. This appliance is hot when in use. To avoid

electric shock, fire or damage to the appliance.

burns, do not let bare skin touch hot surfaces.

14. To prevent fire, do not block air intakes or exhaust

Keep combustible materials, such as furniture,

in any manner. Do not use on soft surfaces, such

pillows, bedding, papers, clothes, and curtains

as a bed, where openings may become blocked.

at least 3 feet(1m.) from the front of this

15. This appliance has hot and arcing or sparking parts

appliance.

inside. Do not use it in areas where gasoline, paint,

3. CAUTION: Extreme caution is necessary when

or flammable liquids are used or stored. This elec-

any heater is used by or near children or inva-

tric fireplace should not be used as a drying rack

lids and whenever the heater is left Operating

for clothing, Also, do not have Christmas stock-

and unattended.

ings or decorations hung on or near it.

4. Always unplug heater when not in use.
16. Use this appliance only as described in this
5. Do not operate any heater with a damaged

manual. All other uses not recommended by the

cord or plug or after the heater malfunctions,

manufacturer may cause fire, electric shock, or

has been dropped or damaged in any manner.

injury.

6. Any repairs to this appliance should be carried
17. Avoid the use of an extension cord because it may

out by a qualified service person.

overheat and cause a fire hazard. However if you

7. Under no circumstances should this electric fire-

must use an extension cord, the cord shall be

place be modified. Parts having to be removed

1.0 mm2,1900 Watts. The extension cord must

for servicing must be replaced prior to operat-

be a three wire cord with grounding type plug

ing this electric fireplace again.

and cord connector. 18.SAVE THESE INSTRUCTIONS.

8. Do not use outdoors.
9. This heater is not intended for use in bathrooms,

LOCATING YOUR ELECTRIC FIREPLACE

laundry areas or similar indoor locations. Never

use this appliance near a bathtub or other wa-

Your new freestanding electric fireplace may be

ter container.

installed virtually anywhere in your home.

10. Do not run cord under carpeting. Do not cover

However when choosing a location for your

new electric fireplace, ensure that the general

cord with throw rugs, runners or the like. Arrange

instructions are followed. For best effect results, install

cord away from traffic areas and where it will not

the electric fireplace out of direct sunlight.

be tripped over.

11. To disconnect this appliance, turn controls to

the off position and remove plug from outlet.

12. Connect to properly grounded outlets only.
Page 4 of the Procom V50TYLAR-BC user manual — REPLACING LIGHT BULBS
Page 4 · click to enlarge
Page 4

CLEARANCE TO COMBUSTIBLES

must comply with local building codes and all other applicable regulations to reduce the risk of fire, electrical shock and injury. WARNING: Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system if necessary.

Sides 0mm

Floor 0mm

Top 610mm

ELECTRICAL CONNECTION

A 10 AMP, 220 Volt,50Hz circuit with a properly grounded outlet is required. Preferably, the stove will be on a dedicated circuit. Other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is on operation. The unit comes standard with a 6’ (1828mm) long three wire cord exiting from the rear of the fireplace. Plan the installation to avoid the use of an extension cord. If an extention cord must be used, it must be a minumum 1.0 mm2 three wire with grounding type plug connector and rated no less than 1900 Watts.

ELECTRICAL SPECIFICATIONS

Total Amps 6.5 Amps

Total Watts 1350 Watts

SERVICE INSTRUCTIONS

7. Install the new light bulb(s) by holding the socket and screwing them. 8. Reinstall the log set and screen. Follow the above procedure in reverse order. 9. The diameter of the pilot light bulb is 5mm. If the pilot light bulb need to be replaced, follow steps 1,2,3,4 above. Then use the pilot light bulb socket w/wiring assembly replace the primary pilot part, and connect wires according to primary connection . Then follow step 8 above.

attempting any maintenance or cleaning

to reduce the risk of fire, electrical shock

REPLACING LIGHT BULBS

This fireplace uses two clear 220 Volt, 60 Watt, E-14 socket base light bulbs (small base, chandelier candle type).The 60 Watt bulbs are located under the log set/ember bed. For convenience, if one of the bulbs burns out, it may be a good

idea to replace both of the light bulbs.

1. Turn off power to the unit by unplugging the power cord.
2. Let fireplace cool if it has been operating.

Watts per bulb. Use of higher

3. Remove the two fixing self-tapping screws on the screen.

rated bulbs may result in a fire

Pull the screen upward a little bit, and then out.

causing property damage and

4. Remove the two screws that secure the log set in position.

personal injury.

5. Examine the bulbs to determine which bulbs need to be

replaced.

6. While holding the socket, unscrew the defective bulb (s).
Show 4 more labels / short text on this page
Back…………………………0mm · Voltage………………220 VAC/50Hz · Heater Ratings………1200 Watts · or personal injury
Page 5 of the Procom V50TYLAR-BC user manual — ELECTRICAL WIRING DIAGRAM
Page 5 · click to enlarge
Page 5

MAINTENANCE OF MOTORS

GLASS INFORMATION

The motors used on the fan and flame genera-

1. Under no circumstances should this product

tor assembly are prelubricated for extended

be operated with missing or broken glass. 2. Do not strike or slam the glass. 3. Do not use abrasive cleaners to clean the glass.

bearing life and require no further lubrication.

However, periodic cleaning/vacuuming of the

fan/heater unit is recommended.

4. Replacement glass is available from the manu

facturer and replacement should be carried out

power is turned off before

by a qualified service person.

proceeding.

ELECTRICAL WIRING DIAGRAM

Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance

with national and local codes.

If repairing or replacing any electrical component or wiring, the original wire

routing, color coding and securing location must be followed.

Page 6 of the Procom V50TYLAR-BC user manual — Operating Instructions
Page 6 · click to enlarge
Page 6

Operating Instructions

This section provides easy step by step instructions for operating your fireplace.

1. Make sure the unit is unplugged from the power source 。
2. Plug the fireplace into a 10AMP/220V outlet. If the cord does not reach, you may use an

extension cord rated for a minimum of 1900 watts.

To access the controls, open the bottom of the fireplace at the front of the unit (see Figure A).

A. MAIN ON/OFF SWITCH The on/off switch supplies power to all fireplace functions (heater/flame). B. HEATER THERMOSTAT CONTROL To adjust the temperature to your needs, turn the thermostat control completely clockwise to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave it in this position to maintain the room temperature at this setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on. To turn the heater off, switch the HEATER ON/OFF SWITCH to the OFF position. C. HEATER ON/OFF SWITCH The HEATER ON/OFF SWITCH supplies power to the heater fan and the heater element. NOTE: When switched ON, the heater fan will operate. The heater element may or may not be on, depending on the thermostat control setting (see “HEATER THERMOSTAT CONTROL”). When the HEATER/FAN pilot light is lighting, it indicate that the heater is on.

not acceptable to use the “ON/OFF” switch to meet this requirement. (Refer to operating

D. INSTRUCTIONS FOR POWER This heater is for use on 220 volts only. The green/yellow grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

instruction section)

Page 7 of the Procom V50TYLAR-BC user manual — SPECIFICATIONS:
Page 7 · click to enlarge
Page 7

SPECIFICATIONS:

ModelV50TYLA-C
ModelV50TYLA-O
Voltage220V/50HZ Total Amps: 6.5A
Voltage220V/50HZ Total Amps: 6.5A
Total Watts1350W Heating Ratings: 1200W
Total Watts1350W Heating Ratings: 1200W

Dimensions, CM (H x W X D)

Dimensions, CM (H x W X D)

Fireplace 97.8x67x35.9

Fireplace 97.8x67x35.9

Carton 105.1x74.5x44.1

Carton 105.1x74.5x44.1

Fireplace 35.9

Fireplace 35.9

Shipping 43.1

Shipping 43.1

ModelV50TYLA-DO
ModelV50TYLA-BC
Voltage220V/50HZ Total Amps: 6.5A
Voltage220V/50HZ Total Amps: 6.5A
Total Watts1350W Heating Ratings: 1200W
Total Watts1350W Heating Ratings: 1200W

Dimensions, CM(H x W X D)

Dimensions, CM (H x W X D)

Fireplace 97.8x67x35.9

Fireplace 97.8x67x35.9

Carton 105.1x74.5x44.1

Carton 105.1x74.5x44.1

Fireplace 35.9

Fireplace 35.9

Shipping 43.1

Shipping 43.1

ModelV50TYLAR-BC
Voltage220V/50HZ Total Amps: 6.5A
Total Watts1350W Heating Ratings: 1200W

Dimensions, CM (H x W X D)

Fireplace 97.8x67x35.9

Carton 105.1x74.5x44.1

Fireplace 35.9

Shipping 43.1

Show 5 more labels / short text on this page
Weight, Kgs · Weight, Kgs · Weight, Kgs · Weight, Kgs · Weight, Kgs
Page 8 of the Procom V50TYLAR-BC user manual — V50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC V50TYLA-BC
Page 8 · click to enlarge
Page 8

REPLACEMENT PARTS PICTURES OF

V50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC V50TYLA-BC

Procom V50TYLAR-BC — V50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC V50TYLA-BC diagram (page 8)
Fig. 2
Procom V50TYLAR-BC — V50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC V50TYLA-BC diagram (page 8)
Fig. 3
Procom V50TYLAR-BC — V50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC V50TYLA-BC diagram (page 8)
Fig. 4
Procom V50TYLAR-BC — V50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC V50TYLA-BC diagram (page 8)
Fig. 5
Page 9 of the Procom V50TYLAR-BC user manual — V50TYLA-O
Page 9 · click to enlarge
Page 9

V50TYLA-O

Item#Part DescripitionPart Number 1Log SetVL050-01A 2Fan/Heater AssemblyNFHTX186-R/VB17-000-R 3Synchronization Motor-220Volt AC w/TerminalFE23A307 4Cord Power H05VV-F3GX1.0 w/TerminalNFHL008-R-A 5ON/OFF SwitchVL067-01 6Heater Control (Thermostat)VL053-02 7Heater Control KnobNFHL012 8Flame Generator Assembly/Firewood Glisten PaperPT/32GS370/FE33A205-01 9Light Bulb Socket w/W iring AssemblyPE28A306-R 10ScreenEB29600 11Top PanelEL040-01-O 12Side Panel (Right/Left)EL015-06-O 13Lower PanelEL012-06 14DoorEL013-01 15Brass Knob224A 16Back PanelEL019-01-B 17BaseEL018-06RA-O 18Upper Decorating FrameEL016-06H-O 19Upper Decorating W ireEL011-01 20Upper (Mid) LouverVL015-01(VL014-01) 21Pilot Light Bulb Socket w/W iring AssemblyVL080-01 22Base Plate ( Not shown)VL091-01-R 23Driverwheel 2(Not shown)VL005-03A 24Switch Mount Panel ( Not shown)VL004-01F
Page 10 of the Procom V50TYLAR-BC user manual — V50TYLA-C
Page 10 · click to enlarge
Page 10

V50TYLA-C

Item#Part DescripitionPart Number 1Log SetVL050-01A 2Fan/Heater AssemblyNFHTX186-R/VB17-000-R 3Synchronization Motor-220Volt AC w/TerminalFE23A307 4Cord Power H05VV-F3GX1.0 w/TerminalNFHL008-R-A 5ON/OFF SwitchVL067-01 6Heater Control (Thermostat)VL053-02 7Heater Control KnobNFHL012 8Flame Generator Assembly/Firewood Glisten PaperPT/32GS370/FE33A205-01 9Light Bulb Socket w/Wiring AssemblyPE28A306-R 10ScreenEB29600 11Top PanelEL040-01-C 12Side Panel (Right/Left)EL015-06-C 13Left Lower Panel/Right Lower PanelEL012-06 14DoorEL013-01 15Brass Knob224A 16Back PanelEL019-01-B 17BaseEL018-06RA-C 18Upper Decorating FrameEL016-06B-C 19Upper Decorating WireEL011-01 20Upper (Mid) LouverVL015-01(EL014-01) 21Pilot Light Bulb Socket w/Wiring AssemblyVL080-01 22Base Plate ( Not shown)VL091-01-R 23Driver Wheel 1/ Driverwheel 2(Not shown)VL005-03A 24Switch Mount Panel ( Not shown)VL004-01F
Page 11 of the Procom V50TYLAR-BC user manual — V50TYLA-DO
Page 11 · click to enlarge
Page 11

V50TYLA-DO

Item#Part DescripitionPart Number 1Log SetVL050-01A 2Fan/Heater AssemblyNFHTX186-R/VB17-000-R 3Synchronization Motor-220Volt AC w/TerminalFE23A307 4Cord Power H05VV-F3GX1.0 w/TerminalNFHL008-R-A 5ON/OFF SwitchVL067-01 6Heater Control (Thermostat)VL053-02 7Heater Control KnobNFHL012 8Flame Generator Assembly/Firewood Glisten PaperPT/32GS370/FE33A205-01 9Light Bulb Socket w/Wiring AssemblyPE28A306-R 10ScreenEB29600 11Top PanelEL040-01-DO 12Side Panel (Right/Left)EL015-06-DO 13Left Lower Panel/Right Lower PanelEL012-06 14DoorEL013-01 15Brass Knob224A 16Back PanelEL019-01-B 17BaseEL018-06RA-DO 18Upper Decorating FrameEL016-06H-O 19Upper Decorating WireEL011-01 20Upper (Mid) LouverVL015-01(VL014-01) 21Pilot Light Bulb Socket w/Wiring AssemblyVL080-01 22Base Plate ( Not shown)VL091-01-R 23Driver Wheel 1/ Driverwheel 2(Not shown)VL005-03A 24Switch Mount Panel ( Not shown)VL004-01F
Page 12 of the Procom V50TYLAR-BC user manual — V50TYLA-BC
Page 12 · click to enlarge
Page 12

V50TYLA-BC

Item#Part DescripitionPart Number 1Log SetVL050-01A 2Fan/Heater AssemblyNFHTX186-R/VB17-000-R 3Synchronization Motor-220Volt AC w/TerminalFE23A307 4Cord Power H05VV-F3GX1.0 w/TerminalNFHL008-R-A 5ON/OFF SwitchVL067-01 6Heater Control (Thermostat)VL053-02 7Heater Control KnobNFHL012 8Flame Generator Assembly/Firewood Glisten PaperPT/32GS370/FE33A205-01 9Light Bulb Socket w/Wiring AssemblyPE28A306-R 10ScreenEB29600 11Top PanelEL040-01-BC 12Side Panel (Right/Left)EL015-06-BC 13Lower PanelEL012-06 14DoorEL013-01 15Brass Knob224A 16Back PanelEL019-01-B 17BaseEL018-06RA-BC 18Upper Decorating FrameEL016-06H-BC 19Upper Decorating WireEL011-01 20Upper (Mid) LouverVL015(VL014-01) 21Pilot Light Bulb Socket w/Wiring AssemblyVL080-01 22Base Plate ( Not shown)VL091-01-R 23Driverwheel 2(Not shown)VL005-03A 24Switch Mount Panel ( Not shown)VL004-01F
Page 13 of the Procom V50TYLAR-BC user manual — V50TYLAR-BC
Page 13 · click to enlarge
Page 13

V50TYLAR-BC

4 Cord Power H05VV-F3GX1.0 w/Terminal NFHL008-R-A

11 Top Panel EL018-06RA-C

12 Side Panel (Right/Left) EL015-06A(B)H-C

13 Left Lower Panel/Right Lower Panel EL012-06

18 Upper Decorating Frame EL016-06B-C

20 Upper (Mid) Louver VL015-01(EL014-01)

23 Driver Wheel 1/ Driverwheel 2(Not shown) VL005-03A

17 Base EL018-06RA-C

Ask about the Procom V50TYLAR-BC

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Procom V50TYLAR-BC

Be the first to ask — other owners or our team will answer.

Original document

Procom V50TYLAR-BC manual PDF

13 pages·8.5 MB·Indoor Fireplace·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…