Instruction/ maintenance manual of the product GS4 ParaBody
Go to page of 27
1 GS4 GYM SYSTEM CLASS H PAR T # 7657901 REV . A Revision: 08/12/05 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULES ! 1. Before u sing, read al l the w arnings and in structions on the use of this machine. Use only for in tended exercise. DO NOT mo dify the machine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody GS4 Gym System. Please read these instructions thoroughly and keep them for future reference.
COMPONENTS P AR TS LIST KEY A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ 4 PA R T # ACU04-1512 ACU04-1511 ACU02-1492 ACU02-1489 ACU02-1490 ACU.
FIGURE 1 5 STEP 1: 19 6 L 3/8 X 3” 8 19 C • LOOSEL Y assemble two BASE PLA TES (C) to the FRAME (A) and BASE (B) using three 3/8 X 3-3/4” BOL TS (6) and four 3/8” LOCK NUTS (19).
6 FIGURE 3 FIGURE 2 • CHECK THA T THE HEADPLA TE AND WEIGHT PLA TES ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3.
FIGURE 4 B AE 29 AD STEP 4: 7 GS4 SHROUD BRACKET OPTION ONL Y AF ** AQ • Insert two GUIDE RODS (AC) into the BASE FRAME (B) as shown on FIGURE 4. (NOTE: If the GS4 SHROUD OPTION was purchased, place the GUIDE RODS (AC) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the BASE FRAME (B) as shown in FIGURE 4.
8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 5: • Carefully slide the RIGHT (N) and LEFT (M) REAR UPRIGHTS over the GUIDE RODS (AC ) as shown in FIGURE 5 and SECUREL Y assembly the RIGHT (N) and LEFT (M) REAR UPRIGHTS to the BASE (B) using four 3/8 X 3-3/4” BOL TS (6), four 3/8” W ASHERS (18) and two 3/8” LOCK NUTS (19) as shown in FIGURE 5.
FIGURE 6 STEP 6: 9 19 AC 29 D E A 3/8 X 3-3/4” 6 • SECUREL Y assemble the LEFT (D) and RIGHT (E) BOOM PLA TES to the FRAME (A) using two 3/8 X 3-3/4” BOL TS (6) and two 3/8” LOCK NUTS (19).
10 • Slide the LEFT (F) and RIGHT (G) PEC FL Y ARMS over the BASE (B) as shown in FIGURE 7. FIGURE 7 STEP 7: B 17 F I G I DO NOT TIGHTEN YET 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECUREL Y assemb.
STEP 8: • SECUREL Y assemble the PEC PLA TE (O) to the BASE (B) using two 3/8 X 2-3/4” BOL TS (9), one 3/8 X 4” BOL T (5), two 3/8” W ASHERS (18) and three 3/8” LOCK NUTS (19) as shown in FIGURE 8.
12 STEP 10: • SECUREL Y assemble one SEA T/BACK P AD (AI) to the SEA T ADJUST (J) using two 3/8 X 2” BOL TS (10) and two 3/8” W ASHERS (18). FIGURE 10 J AI • CAREFULL Y insert the SEA T ADJUST ASSEMBL Y into the FRAME (A) as shown. The SEA T height can be adjusted using the PLUNGER PIN.
13 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 12: • SECUREL Y tighten the two 5/16 X 1/4” SET SCREWS (PRE-INST ALLED)on the FRAME (A) as shown in FIGURE 12. • Insert the PRESS ARM SUPPOR T PIVOT thru the PRESS ARM SUPPOR T FRAME (X) and the FRAME (A).
SPRING PIN 3/8 X 3/4” ALLEN SCREW X H 14 STEP 13: • Insert the PRESS ARM PIVOT SHAFT thru the PRESS ARM (H) and the PRESS ARM SUPPOR T FRAME (X) and the resassemble the 3/8 X 3/4” ALLEN SCREWS and 3/8” LOCK W ASHERS to the PRESS ARM PIVOT SHAFT as shown in FIGURE 13.
3/8 X 3-3/4” 6 AM 19 A 35 26 15 STEP 14: FIGURE 14 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Route the LA T CABLE (AM) through the FRAME (A) and assemble one 3-1/2” PULLEY (35) to the FRAME (A) using one 3/8 X 3-3/4” BOL T (6), two 3/8 X 1-1/16” FLANGE SP ACERS (26) and one 3/8” LOCK NUT (19).
16 STEP 15: FIGURE 15 • Route the LA T CABLE (AM) around one 3-1/2” PULLEY (35) and assemble the PULLEY to the LEFT (D) and RIGHT (E) BOOM PLA TES using one 3/8 X 3-3/4” BOL T (6), two 3/8 X 15/16” SP ACERS (24) and one 3/8” LOCK NUT (19). See FIGURE 15.
STEP 16: FIGURE 16 • Route the LA T CABLE (AM) through the PRESS ARM SUPPOR T FRAME (X) and assemble one 3-1/2” PULLEY (35) to the FRAME PRESS ARM SUPPOR T FRAME (X) using one 3/8 X 8” BOL T (3), two 3/8” W ASHERS (18), two 3/8 X 1-1/4” SP ACERS (25) and one 3/8” LOCK NUT (19).
STEP 17: FIGURE 17 18 • Route the LA T CABLE (AM) around one 4-1/2” PULLEY (36) and assemble the PULLEY to the LEFT (D) and RIGHT (E) BOOM PLA TES using one 3/8 X 3-3/4” BOL T (6), one LONG “L” CABLE BRACE (S), one 1” SP ACER (24) and one 3/8” LOCK NUT (19).
STEP 18: FIGURE 18 19 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Route the PEC FL Y CABLE (AP) around one 4-1/2” PULLEY (36) and assemble the 4-1/2” PULLEY (36) to the DOUBLE FLOA TING PULLEY BRACKET (AA) using one 3/8 X 1-3/4” BOL T (1 1) and one 3/8” LOCK NUT (19).
STEP 19: FIGURE 19 20 • Route the hook end of the GUIDE CABLE (AO) thru the CABLE GUIDE (23) then SECUREL Y assemble the hook end of the GUIDE CABLE (AO) to the BASE using one 3/8 X 3-3/4” BOL T (6), one 3/8” W ASHER (18)and one 3/8” LOCK NUT (19) as shown in FIGURE 19.
STEP 20: FIGURE 20 21 • Route the large ball end of the LOW CABLE (AN) around one V - PULLEY (37) and assemble the PULLEY to the FRAME (A) using two 3/8 X 3-3/4” BOL TS (6), two19/32” FLANGE SP ACERS (28), two 3/8” W ASHERS (18) and two 3/8” LOCK NUTS (19) as shown in FIGURE 20.
STEP 21: FIGURE 21 22 • Route the LOW CABLE (AN) around one 3-1/2” PULLEY (35) and assemble the PULLEY to the PULLEY BRACKET (Z) using one 3/8 X 1-3/4” BOL T (11) and one 3/8” LOCK NUT (19) as shown in FIGURE 21.
STEP 22: FIGURE 22 • Assemble one 3-1/2” PULLEY (35) to the FOOT PLA TE (L) using one 3/8 X 3” BOL T (8), two STEP SP ACERS 11/16” (27) and one 3/8” LOCK NUT (19).
FIGURE 23 AK AG AH 24 22 ADJUSTMENT • If upon completion of assembly , the HEAD PLA TE (AF) does not sit on top of the first WEIGHT PLA TE, push the HEAD PLA TE (AF) down, insert the WEIGHT SELECTOR PIN and perform several repetitions at the press station.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 25 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
26 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED W ARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
An important point after buying a device ParaBody GS4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody GS4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody GS4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody GS4 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody GS4 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody GS4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody GS4.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody GS4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody GS4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
