Instruction/ maintenance manual of the product GS2 ParaBody
Go to page of 24
1 GS2 GYM SYSTEM CLASS H PAR T # 7250101 REV . C Revision: 11/01/02 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody GS2 Gym System. Please read these instructions thoroughly and keep them for future reference.
Minimum Required Usable S p ace Length = 82 inches (208.5 cm) 6’ 10” Width = 71 inches (180.5 cm) 5’1 1” Height = 83 inches (21 1 cm) 6’ 1 1” 1 Square = 1’ X 1’ 4 Length = 82 inches (208.
5 P AR TS LIST 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 PA R T # ACU04-1163 ACU04-1158 ACU02-1060 ACU04-1160 ACU04-1384 ACU04-1383 ACU04-1161 ACU04-1164 ACU04-1159 ACU04-1162 ACU04-1157 ACU02-1071 ACU07-0.
FIGURE 1 6 STEP 1: 1 34 30 2 62 3/8 X 3 29 34 3 • LOOSEL Y assemble two BASE PLA TES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOL TS (30) and four 3/8” LOCK NUTS (34).
7 FIGURE 3 FIGURE 2 • CHECK THA T THE HEADPLA TE AND WEIGHT PLA TES ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3.
• Insert two GUIDE RODS (16) into the BASE (2) as shown on FIGURE 4. (NOTE: If the GS2 SHROUD OPTION was purchased, place the GUIDE RODS (16) through the BOTTOM SHROUD BRACKET (FOUND IN THE SHROUD KIT BOX ) into the BASE (2), as shown in FIGURE 4.
9 STEP 7: • Using hammer tap one 5/16 X 2” ROLL PIN (47) thru LEFT PRESS HANDLE (7) until it is flush with other side of HANDLE as shown in FIGURE 6 8 6 7 FIGURE 6 STEP 6: • Place LEFT PRESS HANDLE (7) onto PRESS ARM (8).
FIGURE 8 8 49 29 36 9 34 STEP 8: • Place PRESS ARM (8) into PRIMAR Y PIVOT (9) and securely tighten using two 3/8 X 3” BOL TS (29), four 3/8” FLA T W ASHERS (36) two 3/8” LOCK NUTS (34) • Insert and tighten two 3/8” T APER/LOCK SPRING PINS (49) into PRESS HANDLES (6), (7).
FIGURE 9 11 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 9 • SECUREL Y TIGHTEN ALL FRAME CONNECTION BEFORE PROCEEDING TO NEXT STEP 33 37 60 48 9 1/2 X 8-3/4” SECUREL Y TIGHTEN • SECUREL Y TIGHTEN t.
12 STEP 10: • Securely tighten the SPRING PIN (50) to the FRAME (1) and hand tighten the ST AR KNOB (52) • Securely assemble one SEA T P AD (13) to the SEA T ADJUSTMENT (10) using two 3/8 X 3” BOL TS (29) and two 3/8” W ASHERS (36) as shown.
FIGURE 1 1 STEP 1 1: • Assemble the LEG PEDEST AL (1 1) to the FRAME (1) using one 1/2 X 104mm BOL T (32), two RH W ASHERS (56) and one 1/2” LOW HT LOCK NUT (35) • Assemble two RH CAPS (55) to t.
ILLUSTRA TION A NOTE: IF YOU PURCHASED A LEG PRESS, PLEASE REFER T O THE CABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEG PRESS KIT 14 • ILLUSTRA TION “A” used as cable routing reference for ste.
15 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Refer to cable ILLUSTRA TION “A” on page 14 for cable r outing while installing pulleys. STEP 13: FIGURE 13 • Assemble one 3-1/2” PULLEY (24) into P.
16 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 14 • Refer to cable ILLUSTRA TION “A” on page 14 for cable routing while installing pulleys. STEP 14: • Assemble one 3-1/2” PULLEY (24) to the .
17 STEP 15 • Screw end of LA T CABLE (20) into top of PLA TE SHAFT (18) and securely tighten JAM NUT as shown in FIGURE 15 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 15 20 • Slip ring of WEIGHT S.
18 • Refer to cable ILLUSTRA TION “A” on page 14 for cable routing while installing pulleys. STEP 16: • [CABLE MUST BE POSITIONED BETWEEN PULLEY AND LOWER BOL T ASSEMBL Y ON LEG PEDEST AL (1 1.
• Refer to cable ILLUSTRA TION “A” on page 14 for cable routing while installing pulleys. STEP 17: • Secure end of LOW CABLE (21) using one 3/8 x 3-3/4” BOL T (30), one 3/8” FLA T W ASHER .
20 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Attach two 4 X 7” ROLLER P ADS (15) to the LEG PEDEST AL (1 1) using one 3/4 X 17” TUBE (14) and two 3/4” ST ARLOCK COLLARS (54) as shown in FIGURE 18.
FIGURE 19 26 17 58 21 57 ADJUSTMENT ADJUSTMENT PULL AND TWIST TO DISENGAGE • If upon completion of assembly , the HEAD PLA TE (19) does not sit on top of the first WEIGHT PLA TE (22), push the HEAD PLA TE (19) down, insert the WEIGHT SELECTOR PIN (51) and perform several repetitions at the press station.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 22 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
23 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
An important point after buying a device ParaBody GS2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody GS2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody GS2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody GS2 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody GS2 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody GS2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody GS2.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody GS2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody GS2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
