Instruction/ maintenance manual of the product Factor 625 ParaBody
Go to page of 10
9/t~ inch wrench ~ odiustable wrench inch wrench ¯ hammer or rubber mallet inch wrench ¯ s~2 allen wrench ¯ THE PARABODY FACTOR 625 BASE UNIT MUST BE ASSEMBLED ON A FLAT, LEVEL SURFACE TO ASSURE ITS PROPER FUNC1 ¯ PARABODY STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASSEMBLED BY TWO PERSONS TO AVOID POSSIBLE INJURY.
TTS/PARTS: OTY. NAME/DESCRIPTION ~ ~(P~78-011 1 Back Pod ~--~B0-01 ) 1 Leg Press Frame ~PB3170-01) 1 Telescoping Tube Plated ~"-’~43-01) l ~~- -- (PB3047-01) 1 Pivot Axle __ [PB3OBI-01) 1 (PB3236-01) l Leg Press Cable 17 ’~ ~634-01) 4 Non-Skid Strip 4" x count all parts before beginning assembly.
If you have installed a second weight stack, go to Figure 5. If you have not purchased the second weight stack, please camp]ere the folJowing steps before proceeding to F~gure 5. 1. Remove the blank shroud from the rear of the Factor 625. 2. Remove the rotary cable from the unit and also the assadated shock cord.
~tinue to route Leg Press cable as shown. ,. ,~emave the boll used to hold the la~ boom 1o ~’he tube an the rear of" lhe Main Frame and ~aih one I1) 4~.,~" w/l" Clevis Pulley and one (1) cable retaining clip using one (t) ~-~" x 4(.
1. AHach the Leg Press Frame to the Main Frame on lop using two {2) l~"x 41~" Bolts, two (2) 1/2" Washers, two (2) I/2" Lockwashers and two (2) 1,~,, nuts. 2. Attach four (4) 4" x17" Non-Skid Strips to the angled foot pl~e on the Leg Press Frame as shown.
SPACER ".--~~ble the spring pin assemblT to the SPR~NG ~autum Frame using one (1) knob, one (I) co~ P~N plunger, one (1) spring, one (1) spacer, and ~kUNG~ (1) co~e~ pin, using the folJowing steps: ~ ~semble the knob to the p~ungsr B. In~d the plunger through the fi~ housing and through the fir~ hole of the second housing.
If] Fig If’ 1. nser~ the seat adjustment tube Into the front end of the Pendulum flame. Pull back the spring pin a~mb/y, and advance the seat adjustment tube al1 the way in. (Make sure tab ai the front end of the seat adiustment tube is up. See figure] I).
. _~.nch the Pendulum Frame to the leg press e by sliding the pivot axle thrnugh the col!ars on the pivot tabs of the leg press flame and through the pivot tube at the top of the pendulum flame. Thread two (2) sA6" x I/4" Ig. set screws into both collars and tighten.
ock res~ tube on the Pendulum Frame using two (2).~/8"x 11/~’~Bohs ’ two (2) ~,~" Lockwashe~, ana ~o ~2) ~8’ Washe~. NOTE: HOL~ IN ~E BACK OF THE S~T BACK PAD AND ~E S~T PAD.
~r ten any loose connedions at this time. FACTOR 625 should be assembled as 11.
An important point after buying a device ParaBody Factor 625 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody Factor 625 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody Factor 625 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody Factor 625 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody Factor 625 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody Factor 625, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody Factor 625.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody Factor 625. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody Factor 625 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
