Instruction/ maintenance manual of the product 917101 ParaBody
Go to page of 17
917101 SMITH MACHINE ASSEMBLY INSTRUCTIONS I I Part # 6"~ 15001 I Revision: 06/09/97.
I IMPORTANT NOTESl ,~ o WELCOME TO THE WORLD OF t~it~U$ Plea’se note: * Thmnk you for purchasing the Parabody 917101 Smith Machine. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
KEY’ 2 3 4 5 6 7 8 9 10 I1 12 13 14 15 PART # ~712002 6711402 6711203 6708901 6711601 6711701 6710201 6710102 6710503 6710403 6710803 6709001 6709901 6709603 6675501 DESCRIPTION BEARING HOUSING SAFE.
FIGURE 2 STEP 2: ¯ CAREFULLY lower on,e COUNTER WEIGHT (14) do~-n into the LEFT UPRIGHT (9) & RIGBT UPR][GHT (10) untiI bottoms out as sho~vn in FIGURE 2.
FIGURE 3 STEP 3: ¯ LOOSELY assemble the LOWER SUPPORT (3) and ~’o PLATE HOLDER (15) to the LEFT & RIGHT UPRIGHTS 10) using four 1/2 X 4-1/2" BOLTS (16) and four 1/2" LOCK NUTS (21) as.
FIGURE 4 STEP 4: ¯ SECURELY assemble fottr PLATE HOLDERS (15) to the LEFT & RIGHT UPRIGHTS (9 & 10) using eight 1/2 BOLTS (17), eight 1/2" WASHERS (20), and eight 1/2" LOCK N-t~TS (.
FIGURE 5 1/2 X 4"~ STEP 5: LOOSELY assemble t~vo CHROME .ANGLES (12) to the top of the LEFT & RIGHT UPRIGHTS (9 & 10) using four 1/2 4-1/2" BOLTS (16), and four 1/2" LOCK NUTS (21) as shown in FIGURE 5. (NOTE: MAKE SIYI~E CABLE IS BETWEEN THE TWO BOLTS.
FIGURE STEP 7: ¯ Loop C.~BLE ASSEMBLIES (26) around the 4-1/2" PULLEYS (27) and route CABLE ASSENEBLY (26) back through UPPER SUPPORT (11)as shown in FIGURE 7.
FIGURE 6 / I l | ~ 7~1/2 X 4" STEP 6: ¯ LOOSELY assemble UPPER SUTPORT (11) to the LEFT & RIGHT UPRIGHTS (9 & 10) u.~-in!~, two 1/2 X 4" BOLTS (17) two 1/2" WASHERS (20)and ~o I/2" LOCK NUTS (21)as shown in FIGURE 6. (NOTE: MAKE SURE CABLE ENSI~E OF THE 1/2" BOLT AS SHOWN I~ DETAIL.
FIGURE 8 STEP 8: ¯ Insert va, o 80" GUIDE ftODS (13) through the BUSHENGS in the UPPER SUPPORT (11) and out lhrough the top, lower the GUIDE RODS (13) dovm into the BUSHING onthe BASE of the UPR.
FIGURE 9 LEFT RIGHT STEP 9: ¯ Slide one 1-1/2," THRUST BEARING (25), one RIGHT SAFETY HOOK (6), and one 1" SHAFT COLLAR (24) over SAFETY STOP (2) as shown in FIG~-R.
FIGURE 11 T RIGHT STEP 11: ¯ Slide one BEARING HOUSING (1), one 2" SHAFT COLLAR (23), and one 2-1/2" OD RUBBER BUMPER (29) over SLEEVE ASSEMBLY (4) as shown in FIGURE 11. ¯ Using a 1/4" Allen wren,:h, SECURELY tighten each set screw on the 2" SHAFT COLLARS (23).
STEP 13: ¯ Lift up each GUIDE ROD (13) and slide one 1" SHAFT COLLAR (24) over the bottom of each GUIDE ROD (13). Position 1" SHAFT COLLAR (24) half way up the GUIDE ROD (13) and tighten it using a 3/16" Allen wrench- See FIGURE 13.
FIGURE 14 BUSHING HOOK I~ ~USHI NG STEP 14: ¯ Lift up on each GUIDE ROD (13) aad slide the RIGHT & LEFT BAR STOP ASSEMBLIES (8) ove~’the bottom of GUIDE ROD (13) onto their respecfi~e sides then lock the HOOKS of the BAR STOPS (8) onto t~e CHROME A~GLES (12) then seat GUIDE RODS (13) back into the BUSHINGS inthe BASE of the UPRIGHTS (9 10 ).
FIGURE STEP 15: ¯ Loosen each 1" SHAFT COLLAR (24) and slide each one up firmly agains~ the BUSHINGS of the UPPER SUPPORT (11). See FIGURE 15. ¯ Using a 3/16" Allen ,~Tcnch, SECURELY tighten each set screw on the 1" SHAFT COLLARS (24).
FIGURE 16 STEP 16: ¯ SECURELY assemble threaded end of CABLE ASSEMBLIES (26) into the BEARING HOUSINGS (1) using one WASHER (20) on each .¢,~de as sho~-a in FIGLrRE 16. * NOTE: Lubricate the GUIDE RODS (13) with a light oil or lubricant that is available at most har,dware s~ores.
FIGURE 17 STEP 17: ¯ MAKE SURE ALL CONNECTIONS ARE TIGHT! Thank you for purcha:;ing the Parabody 917101 Smith Machine. If unsure of proper use of equipment, call your local Parabody d~stributor or call the Parabody customer service department at (800) 328-9714.
An important point after buying a device ParaBody 917101 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 917101 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 917101 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 917101 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 917101 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 917101, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 917101.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 917101. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 917101 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
