Instruction/ maintenance manual of the product 897104 ParaBody
Go to page of 10
I ~~~erious Steel 8971(1’4 WEIGHT STACK OPTION IIII II ASSEMBLY INSTRUCTIONS II Illl Part # 6819801 1 Revisio~a: 2/17/99.
1 2 3 4 5 6 7 8 9 10 11 12 13 PART# DI~CRIPTION QIY /~Y PART# STACKBASE 6819403 STACKBOOM 6819703 1-3/4" X 9..3/8" TUBE 6577801 77-1/4" GUII)E ROD 6284501 3116201 20 HOLE W]EIGHT STACK .
I IMPORTANT NOTES" I WELC, OlVIE TO THE WORLD OF ~t~t~$ $~t~t~J I Please note: * Thank you for pur,chasing the Parabody 897104 WEIGHT STACK OPTION. Please read these instructions ~Lhoroughly and keep them for future reference. This product must be as- sembled on a flat, level surface to assure its proper function.
FIGURE 2 3/8X4" TOP @~ UPPER CROSS 1/2X2-1/2"- ~ 1/2X3" ~’ 3/8X2-3/4" /~ UFRIGHT FRAME STEP 2: ¯ LOOSEN the TOP BOOM fromthe UPRIGHT FRAMEbyremoving one 1/2 X 2-1/2 BOY, one 1/2 X 3" BOL% one 3/8 X 2-3/4" BOLT, two 1/2" WASHERS, one 1/2" LOCKNUT, and one 3/8" LOCK NUT as shown in FIGURE 2.
FIGURE 4 1/2X2-3/4"(~ ;TEP 4: ¯ Insert two 3 X 2" END CAPS, (8) into the ends of the STACK BOOM (2) as shown in FIGURE ¯ Insert two GUIDE ROD BUSHINGS (22) into the tubes onthe STACK BOOM .
FIGURE 6 STEP 6: ¯ SECURELY assemble the STACK BASE (1) to the bottom ofthe UPRIGHT FRAME usmg one l/2 X 3"l/4 BOLT (18)andone 1/2 NUT (20) as shownin FIGURE FIGURE 7 STEP 7: ¯ Snap two WEIGHT .
3/8 X 1-1/4"t FIGURE 8 STEP 8: Insert two GUIDE RODS (4) into the STACK BASE ( 1 ) as shown in HIGURE 8. Lubricate the GUIDE RODS (4) with a slicon or teflon spray that is available at most hardware stores. ¯ Slide two WEIGHT S~[ACK CUSHIONS (21) dom~ over the GUIDE RODS (4).
FIGURE 9 STEP 9: ~PRIGttT Slide the STACK BOOM (21 over the GUIDE ROD S (4) and inside the tube on the UPRIGHT FRAME as shown in FIGURE FIGURE 10 ;TEP 10: ~¢~ -1/2 X 2-1/2" "1/2 X 3" .
FIGURE 11 STEP 11: sure CABLE is routed over bolt! Route the 129-1/2" CABLE (7) through the TOP BOOM and the STACK BOOM (2) as shown in FIGURE TIGttTEN any LOOSENED PULLEY connection after CABLE has been routed.
FIGURE 13 !IMPORTANT! SECURELY TIGHTEN JAMNUT ;TEP 13: ¯ Screw the threaded end of the CABLE (7) approximately 3/4" into the end of the 20 HOLE SELECTOR SHAFT (5) and tighten nut securely. See FIGURE 13. ¯ Insert the WEIGHT STACK PIN (10) into the WEIGHT STACK as shown in FIGURE 13.
An important point after buying a device ParaBody 897104 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 897104 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 897104 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 897104 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 897104 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 897104, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 897104.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 897104. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 897104 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
