Instruction/ maintenance manual of the product 894104A ParaBody
Go to page of 11
! Serious Steel 894104 PEC DEC OPTION Illl I ASSEMBLY INSTRUCTIONS I Part # 6820101 1 Revision:4/26/99.
[ IMPORTANT NOTES’[ WELCOME TO THE WORLD OF SeriOUS ~e~!lt Please no~e: * Thank you for purchasing the Parabody 894104 PEC DEC OPTION. Please read these instructions thoroughly and keep them for future reference. This product r~m,,;t be assembl~l on a fiat, level surface to assure its proper function.
KEY PART # DESCRIPTION 1 6818103 BEARING HOUSING 2 6818403 PEC DEC ARM LEFT 3 6818503 PEC DEC ARM RIGHT 4 6818303 CENTER PULLEY BRACKET 5 6686802 PULLEY BRACKET 6 6597402 BACK PAD 7 6176201 4 X 12&quo.
FIGURE 2 STEP 2: ¯ Assemble t~vo 1 X 1" GLIDES (12) to the BEARING HOUSING (1) as sho~vn in FIGURE ¯ Insert t~vo 2" SQ. END CAPS (11) to the ends of the BEARING HOUSING (1) as shown in FIG.
FIGURE 3 STEP 3: ¯ Insert four 2" SQ. END CAPS (11) into the ends of the LEFT and RIGHT PEC DEC ARMS (2 & 3) as sho~vn in FIGURE ¯ Assemble two 4 X 12" ROLLER PADS (7) to the LEFT and RIGHT PEC DEC ARMS (2 & 3) as shown in FIGURE 3.
FIGURE 4 3/.8 X 2" STEP 4: ¯ LOOSELY assemble two 3-1/2" PULLEYS (8) and two CABLE RETAINING CLIPS (13) to the CEN’IER PULLEY BRACKET (4) using two 3/8 X 2" BOLTS (14), two 3/8" WASHERS (17), and two 3/8" LOCKNUTS (18).
FIGURE 6 LOW HEIGHT STEP 6: Assemble the LEFT & RIGHT PEC DEC ARMS (2 & 3) to the BEARING HOUSING (1) using four 3/4" FLANGE BEARINGS (21), two 1/2" WASHERS (19), and m’o 1/2" LOW HEIGHT LOCK NUTS (22) as shown in FIGURE 6. (Tighten connection securely, then back nut off 1/8 turn or until arm rotates freely.
FIGURE 7 STEP 7: UPRIGHT 3/8X2-3/4", SECURELY assembleBACKPAD (6) to theUPRIGHTFRAMEusingtwo 3/8X2-3/4"BOLTS (15) andtwo 3/8" WASHERS (17) as shown inFIGURE7.
STEP 8 Wrap the 94-1/2" CABLE (9) around one 3-1/2" PULLEY (8) and SECURELY assemble the PULLEY to the PULLEY BRACKET (5) using one 3/8 X 2" BOLT (14) and one LOCKNUT (18) as shown in F.
BLOCK 4-1/2" PULLEY,~ ~ "’~~3/8X2" ~UPRIGHTFRAME 3/8X2-3/4" FIGURE 10 STEP 10: ¯ Route the end of the 134-3/4" CABLE (10) through the slot of the UPRIGHT FRAME then SECUREL.
FIGURE 11 STEP 11: ¯ Wrap the CABLE (10) around one 3-1/2" PULLEY (8) and SECURELY assemble the PULLEY to the plate on the UPRIGHT FRAME using one 3/8 X 2" BOLT (14), one CABLE RETAINING CLIP (13), one 3/8" WASHER (17), and 3/8" LOCK NUT (18) as shown in FIGURE 11.
An important point after buying a device ParaBody 894104A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 894104A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 894104A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 894104A you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 894104A will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 894104A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 894104A.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 894104A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 894104A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
