Instruction/ maintenance manual of the product 881 ParaBody
Go to page of 26
1 881 LEG PRESS ADAPTER KIT FOR 880 GYM SYSTEM CLASS H PAR T # 7168701 REV . C V ersion: 881 102 Revision: 3/08/02 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUAL S W HO USE T HIS TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULES ! 1. Before u sing, read al l the w arnings and in structi ons on the use of this mach ine. Use only for intended exercise. DO NOT mo dify th e machine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 881 LEG PRESS ADAPTER KIT . Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
PARTS LIST 4 PA R T # 7160008 7156001 7156102 31 16201 3102501 3102802 3102924 3102922 3102905 3102935 KEY 1 2 3 4 5 6 7 8 9 10 QTY 1 1 1 9 7 8 4 2 3 5 PA R T # 6533501 3102807 6122701 6480301 7242408.
STEP 1: FIGURE 1 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • REMOVE the LA T CABLE, THREADED HOUSING , 3/8 X 3-3/4” BOL T , two 3/8 X 1” SP ACERS and one 3/8” LOCK NUT from the 880 GYM SYSTEM. See FIGURE 1. Save the LA T CABLE if you ever plan to purchase the SECOND ST ACK OPTION.
6 STEP 2: FIGURE 2 • Remove the PEC ST A TION P AD from the FRAME, then discard the two 3/8 X 2-3/4” BOL TS. See FIGURE 2. 3/8 X 2-3/4” STEP 3: FIGURE 3 • SECUREL Y assemble the PULLEY BRACKET (15) and the PEC ST A TION P AD to the FRAME using two 3/8 X 3” BOL TS (18).
STEP 4: FIGURE 4 7 • Remove the two 3/8 X 4” BOL TS, four 3/8” W ASHERS and two 3/8” LOCK NUTS from the REAR UPRIGHT as shown in FIGURE 4. Discard the 3/8 X 4” BOL TS.
STEP 6: FIGURE 6 • Route the SHOR T LEG CABLE (2) through the FRAME and BOOM BRACKET as shown in FIGURE 4. (NOTE: Remove pulleys for ease of installation.
STEP 7: FIGURE 7 • Route the SHOR T LEG PRESS CABLE (2) through the PULLEY PLA TES as shown in FIGURE 7. 3/8 X 1-3/4” 7 • Route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and assemble the PULLEY to the PULLEY BRACKET (15) using one 3/8 X 1-3/4” BOL T (7) and one previously removed 3/8” LOCK NUT .
STEP 8: FIGURE 8 • Remove the 3-1/2” PULLEY , one 3/8 X 3-3/4” BOL T , two 3/8 X 1” SP ACERS and one 3/8” LOCK NUT from the BASE PLA TES as shown in FIGURE 8.
11 STEP 10: FIGURE 10 • SECUREL Y assemble the LEG PRESS ADAPTER (1) to the BASE FRAME using one 3/8 X 3-3/4” BOL T (9), one previously removed 3/8 X 3-3/4” BOL T , two 3/8” W ASHERS (5), two previously removed 3/8” W ASHERS and two 3/8” LOCK NUTS (6) as shown in FIGURE 10.
12 FIGURE 12 STEP 12: • Carefully route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the BRACKET (from 100 LEG PRESS kit) using one 3/8 X 1-3/4” BOL T (7), one 3/8” W ASHER (5), one CABLE CLIP (1 1) and one 3/8” LOCK NUT (6) as shown in FIGURE 12.
13 FIGURE 14 STEP 14: • Carefully route the LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the bracket on the SEA T FRAME using one 3/8 X 1-3/4” BOL T (7) and one 3/8” LOCK NUT (6) as shown in FIGURE 14.
FIGURE 15 STEP15: • Carefully route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8” FLANGE SP ACERS (14), two 3/8 X 1” SP ACERS (13) and one 3/8” LOW HEIGHT LOCK NUT (12) as shown in FIGURE 15.
FIGURE 18 STEP 18: • Carefully route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the MAIN ARM using one 3/8 X 2-3/4” BOL T (8), two 3/8” FLANGE SP ACERS (14) and one 3/8” LOCK NUT (6) as shown in FIGURE 18.
FIGURE 19 STEP 19: 3/8 X 4-1/2” 10 2 12 13 SEA T FRAME 14 16 • SECUREL Y assemble the threaded end of the SHOR T LEG PRESS CABLE (2) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8 X 1” SP ACERS (13), one previosly removed THREADED HOUSING , two 3/8” FLANGE SP ACERS (14) and one 3/8”LOW HEIGHT LOCK NUT (12).
FIGURE 20 STEP 20: • T o set the correct amount of tension in the cables, push the HEAD PLA TE down, insert the WEIGHT SELECT OR PIN and perform several repititions at the leg press station.This will relax the cable system and prevent the HEAD PLA TE from lifting up.
STEP 1: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • If the SECOND ST ACK OPTION has not been assembled to the 880, refer to the SECOND ST ACK OPTION USER’S GUIDE.
STEP 2: FIGURE 2 19 • Route the LONG LEG PRESS CABLE (3) around the 3-1/2” PULLEY on the PULLEY PLA TES using one existing 3/8 X 1-3/4” BOL T and one existing 3/8” LOCK NUT .
20 STEP 3: FIGURE 3 • Remove the two 3/8” BOL TS, 3/8” W ASHERS and 3/8” LOCK NUTS from the ST ACK BASE as shown in FIGURE 3. ST ACK BASE • SECUREL Y assemble the LEG PRESS ADAPTER (1) to the ST ACK BASE using the previously removed 3/8” BOL TS, 3/8” W ASHERS and 3/8” LOCK NUTS as shown in FIGURE 3.
21 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 5 STEP 5: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the BRACKET (.
22 FIGURE 7 STEP 7: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the bracket on the SEA T FRAME using one 3/8 X 1-3/4” BOL T (7) and one 3/8” LOCK NUT (6) as shown in FIGURE 7.
FIGURE 8 STEP 8: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8” FLANGE SP ACERS (14), two 3/8 X 1” SP ACERS (13) and one 3/8” LOW HEIGHT LOCK NUT (12) as shown in FIGURE 8.
FIGURE 1 1 STEP 1 1: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the MAIN ARM using one 3/8 X 2-3/4” BOL T (8), two 3/8” FLANGE SP ACERS (14) and one 3/8” LOCK NUT (6) as shown in FIGURE 1 1.
FIGURE 12 STEP 12: 3/8 X 4-1/2” 10 3 12 13 SEA T FRAME 14 25 • SECUREL Y assemble the threaded end of the LONG LEG PRESS CABLE (3) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8 X 1” SP ACERS (13), one previosly removed THREADED HOUSING , two 3/8” FLANGE SP ACERS (14) and one 3/8”LOW HEIGHT LOCK NUT (12).
26 STEP 13: • T o set the correct amount of tension in the cables, push the HEAD PLA TE down, insert the WEIGHT SELECT OR PIN and perform several repititions at the leg press station.This will relax the cable system and prevent the HEAD PLA TE from lifting up.
An important point after buying a device ParaBody 881 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 881 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 881 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 881 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 881 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 881, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 881.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 881. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 881 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
