Instruction/ maintenance manual of the product 445104 ParaBody
Go to page of 15
445104 425 SECOND ST ACK OPTION Part # 6865201 Revision: 2/15/00 1 ASSEMBL Y INSTRUCTIONS.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the Parabody 445104 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
STEP 2 FIGURE 2 FIGURE 1 STEP 1 • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD. See FIGURE 1.
STEP 3 FIGURE 3 4 • Unscrew the threaded ends of the HEAD PLA TE CABLE from the WEIGHT ST ACK SHAFT & the D-RING and remove HEAD PLA TE CABLE. The HEAD PLA TE CABLE will be used later .
5 PRESS CABLE (67249) STEP 4 • Remove the PRESS CABLE (67249) from the KEYHOLE CLEVIS and ELASTIC CORD. (NOTE: The LA T or LEG EXT CABLE can be moved over one hole on the D-RING so the KEYHOLE CLEVIS are evenly spaced .) FIGURE 4 ELASTIC CORD D-RING KEYHOLE CLEVIS • Discard the KEYHOLE CLEVIS and ELASTIC CORD.
6 STEP 6 FIGURE 6 • Assemble the previously removed 2” PULLEY to the bracket on the TOP BOOM using one 3/8 X 1” BOL T (1 1), one previously remov ed 3/8” W ASHER, and one previously removed 3/8” LOCK NUT . See FIGURE 6. • (NOTE: STEP 6 is only if the 435101 LEG PRESS OPTION is installed otherwise proceed to STEP 7.
FIGURE 8 STEP 8 • Discard the two 3/8 X 1/2” SP ACERS. • Remove two 2” PULLEYS (5) to the rear bracket on the TOP BOOM using one 3/8” THREADED SHAFT (9), two 3/8” W ASHERS, two 3/8” HEX NUTS (8), and two 3/8” LOCK NUTS (7) as shown in FIGURE 8.
STEP 10 • Carefully remove and discard the PRESS CABLE as shown in FIGURE 10. PRESS CABLE (67249) FIGURE 10 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2.
9 STEP 1 1 • Route the new PRESS-ST ACK CABLE (5) around the pulleys and l-brackets as shown in STEP 1 1. (Remove pulleys for ease of installation.) 5 5 FIGURE 1 1 FIGURE 12 STEP 12 PRESS-ST ACK CAB.
FIGURE 14 STEP 14 • LOOSEN the bolts holding the TOP BOOM to the UPRIGHTS. Bolts will have to be removed to install GUIDE RODS (1). See FIGURE 14. 10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 13 • Insert two WEIGHT PLA TE BUSHINGS (17) into the top side of each of the fifteen WEIGHT PLA TES (16) as shown in FIGURE 13.
FIGURE 15 STEP 15 • Insert two GUIDE RODS (1) into the BASE as shown on FIGURE 15. (NOTE: Lubricate GUIDE RODS (1) with silicon or teflon spray available at most hardware stores.) • Slide two 1-1/4 SQ. X 4-7/8” TUBES (3), two 3/4” W ASHERS (15), and two WEIGHT ST ACK CUSHIONS (8) - IN THA T ORDER - down over the GUIDE RODS (1).
STEP 16 FIGURE 16 12 • W ith the GUIDE RODS (1) securely held in the TO P BOOM. T ighten all T OP BOOM connections. (NOTE: Make sure the LA T CABLE runs over the top of the bolts in the TOP BOOM.) 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 TIGHTEN! ( NOTE: Make sure LA T CABLE runs over top of bolts in TOP BOOM.
13 HEAD PLA TE CABLE (67250) STEP 17 FIGURE 17 • Screw one of the threaded ends of the previously removed HEAD PLA TE CABLE approximately 1” into the end of the WEIGHT ST ACK SHAFT . See FIGURE 17. WEIGHT ST ACK SHAFT STEP 18 • Screw the other threaded end of the HEAD PLA TE CABLE approximately 1” into the end of the shaft on the D-RING.
STEP 19 FIGURE 19 14 REAR SHROUD • The rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the plastic SHROUD as shown in FIGURE 19.
STEP 21 FIGURE 21 FIGURE 20 STEP 20 • SECUREL Y attach the four previously removed 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD.
An important point after buying a device ParaBody 445104 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 445104 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 445104 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 445104 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 445104 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 445104, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 445104.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 445104. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 445104 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
