EN
Linear logo
Official user manual

Linear D-22D

1 pages·78 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear D-22D
Table of Contents 19 sections (619) 438-7000 • FAX (619) 438-7043 · CODING · SWITCH · OUTPUT POWER · … ShowHide
Page 1 of the Linear D-22D user manual — REMOVE BATTERY
Page 1 · click to enlarge
Page 1
D-22D DIGITAL TRANSMITTER Code Setting Instructions (619) 438-7000 • FAX (619) 438-7043 USA & Canada (800) 421-1587 & (800) 392-0123 Toll Free FAX (800) 468-1340TRANSMITTER DESCRIPTION D-22D transmitter switch key 1 is unused and can be set in The D-22D is a two-button, two-channel hand-held digital radio any position. The transmitter pushbuttons control the signal that transmitter with a special lock-out feature. The transmitter can would normally be controlled by switch key 1. Pressing either perform a variety of remote switching tasks when used with any of pushbutton sends a signal as if switch key 1 is OFF. Pressing both Linear’s Standard Digital “D” Series Receivers. Typically the pushbuttons sends a signal as if switch key 1 is ON. D-22D is used in wireless or hybrid wireless/hardwire security 1 CAUTION: All Standard Digital transmitters and receivers should be systems. recoded prior to installation and operation. The transmitter is powered by a 9-volt battery. Pressing either In order to avoid the possibility of duplicating codes in adjacent button will send a “Channel 1" signal, pressing both buttons will systems, factory set codes should not be used. In addition, among send a ”Channel 2" signal. Hold buttons for at least 2 seconds the valid codes available, four others should not be used. These to activate the transmitter. The red LED on the face of the include: all keys set ON or OFF and keys set in an alternating transmitter will glow as the unit transmits and the receiver with the ON/OFF or OFF/ON pattern. matching digital code will activate. The D-22D will transmit as long as a pushbutton is pressed. The Standard Digital radio format provides up to 256 different Depending on conditions (interference, obstacles and distance to the digital codes. The code is set using the 8-position coding switches receiver) the receiver output may or may not stay activated for as in the transmitter and receiver. long as the transmitter is sending a signal. 1 CAUTION: If using two receivers, be sure they are located at least 10 feet apart. STEP 1 Locate coding switch. Remove the battery access door located on the back of the transmitter case. Identify the coding switch and note that it has eight positions, with ON and OFF clearly marked. REMOVE BATTERY ACCESS DOOR CODING SWITCHSTEP 2A Coding for single-channel receivers. Pick any valid combination of OFF/ON codes and set them on switch keys 2-8 in the transmitter Match the same code on switch keys 2-8 in the receiver. Set receiver switch key 1 to OFF for the receiver to activate from either transmitter button (Channel 1). Set receiver switch key 1 to ON for the receiver to activate only when both transmitter buttons are pressed (Channel 2). CODING SWITCHES IN RECEIVER D-22D CODING SWITCH RECEIVER FOR TRIGGERS FROM CHANNEL 1 EITHER BUTTON MATCH MATCH 2-8 2-8 SET 1 OFF SET SET KEYS 1 ON KEY 1 IS 2-8 TO ANY RECEIVER FOR TRIGGERS FROM UNUSED CODE CHANNEL 2 BOTH BUTTONSSTEP 2B Coding for two-channel receivers. Pick any combination of OFF/ON codes and set them on switch keys 3-8 in the receiver. Match the same code on switch keys 3-8 in the transmitter. Set the transmitter switch 2 to OFF. Either button will activate Channel 1, both buttons will activate Channel 2. 2-Channel receiver switch keys 1 & 2 are unused and can be set in any position. D-22D CODING SWITCH CODING SWITCH IN TWO-CHANNEL RECEIVER SET KEYS 3-8 TO MATCH CODE ANY VALID CODE ON KEYS 3-8 KEY 1 IS SET KEY KEYS 1 & 2 UNUSED 2 OFF ARE UNUSED STEP 3 Test the equipment. Connect the receiver to its power source. With relay output receivers, listen for the relay click when the transmitter is activated. A multi-meter can be used to detect activation of relay and solid state output receivers. Operate the transmitter from various locations to determine the radio range. DCV DCV MEASURE MEASURE MEASURE RESISTANCE VOLTAGE VOLTAGE NORMALLY POWER POWER COMMON OPEN OUTPUT OUTPUT SHORT -TORELAY VOLTAGE COMMON OUTPUT OUTPUT OUTPUT RECEIVER RECEIVER RECEIVERBATTERY REPLACEMENT The battery should last 12 to 18 months with normal use. When the red LED lights dimly, or not at all when transmitting, the battery needs to be replaced. Remove the battery access door to change the battery. Any type of 9-volt battery can be used. Replace the battery door and foam battery pad when finished. REPLACE BATTERY WITH FRESH 9-VOLT BATTERYLINEAR LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. For warranty service on Linear equipment return product, at sender’s expense to: Linear Corporation Repairs Department 2580 Pioneer Avenue, Suite C Vista, CA 92083 IMPORTANT !!! Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there are some limitations which must be observed. 1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. 1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. 1 Changes or modifications to the device may void FCC compliance. 1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault. 1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. Copyright © 1994 Linear Corporation 200858 B
Linear D-22D — (619) 438-7000 • FAX (619) 438-7043 diagram (page 1)
Fig. 1

(619) 438-7000 • FAX (619) 438-7043

CODING

SWITCH

OUTPUT POWER

Toll Free FAX (800) 468-1340

VOLTAGE

OUTPUT

RECEIVER

MEASURE

VOLTAGE

TRANSMITTER

D-22D

RECEIVER

Code Setting

OFF clearly marked.

REMOVE BATTERY

MEASURE

RESISTANCE

NORMALLY

RELAY

OUTPUT

ACCESS DOOR

OPEN COMMON

Instructions

DIGITAL

Ask about the Linear D-22D

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear D-22D

Be the first to ask — other owners or our team will answer.

Original document

Linear D-22D manual PDF

1 pages·78 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…