EN
Linear logo
Official user manual

Linear D-22C

1 pages·116 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear D-22C
Table of Contents 18 sections (760) 438-7000 • FAX (760) 438-7043 · OUTPUT POWER · VOLTAGE · OUTPUT · … ShowHide
Page 1 of the Linear D-22C user manual — VOLTAGE
Page 1 · click to enlarge
Page 1
D-22C DIGITAL TRANSMITTER Code Setting Instructions (760) 438-7000 • FAX (760) 438-7043 USA & Canada (800) 421-1587 & (800) 392-0123 Toll Free FAX (800) 468-1340TRANSMITTER DESCRIPTION The D-22C transmitter contains two 8-position dipswitches, one The D-22C is a two-button, two-channel hand-held digital radio for each pushbutton. The transmitter can be used with two transmitter with independent button coding. The transmitter can single-channel receivers or one multi-channel receiver. perform a variety of remote switching tasks when used with any of 1 CAUTION: All Standard Digital transmitters and receivers should be Linear’s Standard Digital “D” Series Receivers. Typically the recoded prior to installation and operation. D-22C is used in wireless or hybrid wireless/hardwire security In order to avoid the possibility of duplicating codes in adjacent systems. systems, factory set codes should not be used. In addition, among The transmitter is powered by a 9-volt battery. Pressing either the valid codes available, four others should not be used. These button will send that button’s unique code. Press either button include: all switches set ON or OFF and switches set in an for at least 2 seconds to activate the transmitter. The red LED alternating ON/OFF or OFF/ON pattern. on the face of the transmitter will glow as the unit transmits and The D-22C will transmit as long as a pushbutton is pressed. the receiver with the matching digital code will activate. Depending on conditions (interference, obstacles and distance to the A snap-on plastic transmitter clip with a screw and double-stick receiver) the receiver output may or may not stay activated for as tape for mounting the transmitter are provided with the unit. long as the transmitter is sending a signal. The Standard Digital radio format provides up to 256 different 1 CAUTION: If using two receivers, be sure they are located at least 10 feet digital codes. The code is set using the 8-position coding switches apart. in the transmitter and receiver(s). STEP 1 Locate coding switches. The code switch for the left button can be accessed by removing the battery access door located on the back of the transmitter case. To access the code switch for the right button, the unit’s rear cover must be removed. Identify the coding switches and note that they have eight positions, with ON and OFF clearly marked. REMOVE BATTERY DOOR TO ACCESS THE RIGHT BUTTON TO ACCESS LEFT BUTTON CODING SWTICH, REMOVE THE CODING SWITCH CASE SCREW AND BACK OF CASE LEFT BUTTON CODING SWITCHSTEP 2A Coding for single-channel receivers. Pick two valid OFF/ON codes and set them on switches 1-8 on each coding switch in the transmitter. Set each receiver’s coding switch 1-8 to match the code set for the proper button in the transmitter. CODING SWITCHES IN CODING SWITCHES D-22C TRANSMITTER IN TWO RECEIVERS SET MATCH 1-8 1-8 LEFT RECEIVER #1 BUTTON ACTIVATES FROM CODING LEFT BUTTON SWITCH EXAMPLE EXAMPLE 3 & 6 ON 3 & 6 ON SET MATCH 1-8 1-8 RIGHT RECEIVER #2 BUTTON ACTIVATES FROM CODING RIGHT BUTTON SWITCH EXAMPLE EXAMPLE 2, 3, 6 & 7 ON 2, 3, 6 & 7 ONSTEP 2B Coding for two-channel receivers. Pick one valid OFF/ON code and set it on switches 3-8 in the receiver. Match the same code on switches 3-8 on both switches in the transmitter. Set both the transmitter switches 2 to OFF. Set one transmitter switch 1 to OFF and the other switch 1 to ON. 2-Channel receiver switches 1 & 2 are unused and can be set in any position. CODING SWITCHES IN CODING SWITCHES D-22C TRANSMITTER IN TWO-CHANNEL RECEIVER MATCH 3-8 LEFT BUTTON RECEIVER C SWOD ITIN CG H E 3X &A M 6 P OL NE S 3E -8T ACC TH IVA AN TN EE SL F # R1 OM SWITCH 1 OFF LEFT BUTTON MATCH RECEIVER 3-8 CHANNEL #2 ACTIVATES FROM RIGHT E 3X &A M 6 P OL NE RIGHT BUTTON BUTTON EXAMPLE CODING 3 & 6 ON SWITCH SWITCH 1 ON STEP 3 Test the equipment. Connect the receiver to its power source. With relay output receivers, listen for the relay click when the transmitter is activated. A multi-meter can be used to detect activation of relay and solid state output receivers. Operate the transmitter from various locations to determine the radio range. DCV DCV MEASURE MEASURE MEASURE RESISTANCE VOLTAGE VOLTAGE NORMALLY POWER POWER COMMON OPEN OUTPUT OUTPUT SHORT -TORELAY VOLTAGE COMMON OUTPUT OUTPUT OUTPUT RECEIVER RECEIVER RECEIVERBATTERY REPLACEMENT The battery should last 12 to 18 months with normal use. When the red LED lights dimly, or not at all when transmitting, the battery needs to be replaced. Remove the battery access door to change the battery. Any type of 9-volt battery can be used. Replace the battery door and foam battery pad when finished. REPLACE BATTERY WITH FRESH 9-VOLT BATTERYLINEAR LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details. IMPORTANT !!! Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there are some limitations which must be observed. 1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. 1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. 1 Changes or modifications to the device may void FCC compliance. 1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault. 1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. Copyright © 1997 Linear Corporation 200857 C
Linear D-22C — (760) 438-7000 • FAX (760) 438-7043 diagram (page 1)
Fig. 1

(760) 438-7000 • FAX (760) 438-7043

positions, with ON and OFF clearly marked.

OUTPUT POWER

Toll Free FAX (800) 468-1340

VOLTAGE

OUTPUT

RECEIVER

MEASURE

VOLTAGE

TRANSMITTER

D-22C

REMOVE BATTERY DOOR

TO ACCESS LEFT BUTTON

RECEIVER

Code Setting

MEASURE

RESISTANCE

NORMALLY

RELAY

OUTPUT

OPEN COMMON

Instructions

CODING SWITCH

DIGITAL

Ask about the Linear D-22C

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear D-22C

Be the first to ask — other owners or our team will answer.

Original document

Linear D-22C manual PDF

1 pages·116 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…