EN
Linear logo
Official user manual

Linear 4120

2 pages·71 KB·Satellite Radio·PDF·ENDEFRITNLJA
Linear 4120
Table of Contents 11 sections MODEL 4120 TWO CHANNEL TRANSMITTER · INSTALLATION INSTRUCTIONS · ACCESSING THE CODE SWITCH · LINEAR LLC · … ShowHide
Page 1 of the Linear 4120 user manual — PLEASE NOTE
Page 1 · click to enlarge
Page 1

Congratulations! You have just purchased a MULTI-CODE Digital Transmitter,

which we believe to be the fi nest product of its kind on the market. With little care

this transmitter should provide you with many years of excellent service. Please

take a moment to read the following instructions and you will fi nd that setting your

Insert a small coin into the slot located at the bottom end of the transmitter. Twist

the coin and remove the access cover to expose the code switches and battery

MODEL 4120 TWO CHANNEL TRANSMITTER

INSTALLATION INSTRUCTIONS

now transmitter will be quite an easy matter.

ACCESSING THE CODE SWITCH

compartment.

Linear LLC has devoted a great deal of time and research in order to provide the

(1) MULTI-CODE radio components must conform with FCC Part 15 requirements.

(2) As with all manufacturers, Linear LLC radios must accept all signals that they

(3) You should test your entire system occasionally in order to be sure that all

(4) Linear LLC dealers can provide you with information regarding the use of our radio

controls, and can provide valuable installation and operation information, when

which are not expressly approved by LINEAR LLC could void the user’s authority

to operate this equipment. This applies to intentional and unintentional radiators

Copyright © 2008 Linear LLC 214881 B

For this reason, the range and power of our radios is within specifi ed limits.

most reliable equipment possible. Certain limitations must be observed.

(800) 421-1587 • (760) 438-7000

receive. This may, in rare instances, create diffi culty.

certifi ed per Part 15 of the F.C.C. rules and regulations.

www.linearcorp.com

LINEAR LLC

components areworking in good order.

PLEASE NOTE

requested.

®

Page 2 of the Linear 4120 user manual — CODING
Page 2 · click to enlarge
Page 2

Channel 1 on the receiver is selected by moving the 10th position of the transmitter

side A to the off (open) position. Channel 2 is selected by moving the 10th position

of the transmitter side B to the on (closed) position. Once the codes have been set,

The transmitter is completely self contained, including battery, and can be operated

while mounted in the car. It is supplied with a clip for attaching to the sun visor, if

desired. If the clip is used, attach to the case by sliding it into the recess provided

ALL MULTI-CODE door related products carry a eighteen (18) month warranty

against defects in workmanship or material. This warranty begins at the date of

manufacture, for eighteen months. Linear LLC warranties our product only to our

authorized dealers and distributors, and not to the end customer. If you have nay

questions about our warranty, please ask your dealer to determine the nature and

scope of his warranty. Linear LLC does not assume, and is not responsible for,

any real or consequential damages from claims against the performance of our

product, nor is it liable for any costs related to loss of life, property, or revenue.

Further, Linear LLC is in no way responsible for installation of our product, and will

assume no costs to reinstallation or removal. Linear LLC Warranty is in lieu of all

on the back of the transmitter until the small dimples fi t into the holes in the clip.

check the operation and replace the lower cover.

other warranties, expressed, or implied.

TRANSMITTER INSTALLATION

WARRANTY

Before placing your transmitter into service, we urge you to set your codes, in

order not to interfere with neighboring systems, and to provide security for your

own system. You will note that the model 4120 transmitter has two, ten position

code switches (see fi gure 1). We strongly urge that several coding schemes be

avoided: ALL ON; ALL OFF; 2, 4, 6, 8, 10, ON; 1, 3, 5, 7, 9, ON. These positions

If you have two single channel receivers: Set your transmitter so that the ten

position switch on side A will match your receiver #1. Set the ten position switch

If you have a MULTI-CODE™ 3021 or 3028 two channel receiver: Set the

receiver and transmitter (side A and B) code switch positions 1-9 to match. The

are similar to our or other manufacturer’s test positions, or are frequently used.

10th position on your transmitter code switches are used for channel selection.

CODE SWITCH

on transmitter side B to your receiver #2 (see fi gure 2).

SIDE B

CODE SWITCH

SIDE A

Figure 1 CODE SWITCH

CODING

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Linear 4120

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear 4120

Be the first to ask — other owners or our team will answer.

Original document

Linear 4120 manual PDF

2 pages·71 KB·Satellite Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…