Instruction/ maintenance manual of the product SM80 Life Fitness
Go to page of 23
M051-K50-B116 1 8 STA CK MULTI-JUNGLE (SM80) WITH HIGH & LOW PULLEYS UNPA CKING A ND A SSEMBLY INSTRUCTIONS.
SM80 U npacking & Assembly Instructions 2 The SM80 c om es partially assem bled. Follow the steps below to com plete the as sem bly. WA RNING: COMPONENTS O F THE SM80 ARE LARGE AND HEAVY.
SM 80 Unpacking & Assembly Instr uctions 3 UNPA CKING Follow the steps below when unpacking the c om ponents of the SM80. 1. Cut off the shipping wrapper. 2. Remove th e parts boxes an d shippin g boards. 3. Remove th e items in the part s boxes. T hese item s ar e shown in Figure 1.
SM80 U npacking & Assembly Instructions 4 A SSEMBLY Figure 2 shows an ass em bled SM80. Figure 2. SM80 main components (seats and cables remov ed for clarity). 1. Cubes (2) 2. Low row bench (2) 3. Lat bench ( 2) 4. Connecting beam (1) 5. Lat tops (2) 6.
SM 80 Unpacking & Assembly Instr uctions 5 Figure 3. Set t he w eight stack cu bes. 2. Bolt on the teardr op pulleys above the benches (see Figure 4) on both cubes using two 3/8” x 2-3/4” hex head bolts (us ed to bolt the cross beam to the cross mem ber s and the adjus table pulley tops to the top beam s).
SM80 U npacking & Assembly Instructions 6 Figure 4. Bolt on the te ardrop pulleys. Figure 5. Configura tion for 6” bolts..
SM 80 Unpacking & Assembly Instr uctions 7 Figure 6. Configura tion for 2-3/4” and 3” bolts. 3. Bolt on the connecting bea m ( part 4 fr om Figure 2) using a 5/8” sock et with extension and com bination wrenc h, to the cubes using two of the large 7/16” x 6” bolts, 7/16” washers , and 7/16” nuts, end cap washer s and end caps.
SM80 U npacking & Assembly Instructions 8 Figure 8. Mount rubber bumpers and the w eight stacks. 5. Install the w eight stacks. T o do this: A. Using a 9/16” soc ket and c om bination wrench, rem ove the tric ep back rest bolts (see Figure 9) . B.
SM 80 Unpacking & Assembly Instr uctions 9 C. Prepare the w eight stack. Slide the guide rods ( 2) through the weight stack s (1) as shown below. Place rubber bum pers (3) on the bottom s of each guide rod. Make s ure the pull pin (4) is in the bottom weight plate.
SM80 U npacking & Assembly Instructions 10 6. Bolt the f loating pu lleys into the 190 lb w eight stacks used f or the cros sovers using a 7/8” com bination wrenc h. You will need to remove the pulley from the housing to thread the plug into the weight stack bayonet.
SM 80 Unpacking & Assembly Instr uctions 11 3/8 x 3” (2) 3/8 x 2-3/ 4” (8) Use a pi nch bar to al ign the seat fram e hol es to the cubes Figure 13.
SM80 U npacking & Assembly Instructions 12 INSTA LLING THE CABLES The SM80 us es eight cables. T here ar e three diff erent types of cable used on the SM80. T hey are: 1. Crossover cables ( ball end cables) ( 2). 2. Low row cable (the long cables) (2).
SM 80 Unpacking & Assembly Instr uctions 13 CROSSOVER CABLE RO UTI NG Once you’ve removed the pulleys as desc ribed previously, route the two crossover cables as shown in Figure 16. Figure 16. Cr os sov er cable routing. LOW RO W CABLE RO UTING Route the low row cables as shown in Figure 17.
SM80 U npacking & Assembly Instructions 14 Figure 17. Low row cable routing..
SM 80 Unpacking & Assembly Instr uctions 15 Bolt the cable to the weight stack s as s hown in Figure 18. Thr ead the 7/8” nut up on the cable bolt as shown at lef t. Screw the bolt down into the weight stack as shown at right. Tighten the bolt with a 7/8” com bination wrench.
SM80 U npacking & Assembly Instructions 16 TRICEP PUSHDOW N CABLE RO UTI NG Route the tricep pushdown cable as shown in Figure 20. Screw the cable into the weight stac k as shown previously in Figure 18. Figure 20. Tricep pus hdow n cable routing.
SM 80 Unpacking & Assembly Instr uctions 17 HA RDWARE 0123456 ½½½½½½ Hardware F igure 1. Assembly Parts..
SM80 U npacking & Assembly Instructions 18 The parts shown in Hardware Figure 1 are us ed to assem ble the SM80. T hey are: A. 7/16” x 6” hex head bolt (used to bolt the tric ep top beam s, lat top beam s, and connecting beam to the tops of the cubes) B.
SM 80 Unpacking & Assembly Instr uctions 19 Hardware Figure 3. Cables . N. Lat pulldown cables (sam e as tricep cable) (2) P. Tric ep cable (s am e as lat pulldown cables) ( 2) Q.
SM80 U npacking & Assembly Instructions 20 Hardware F igure 4. T op assemblies. S. Teardr op pulleys (bolt on above lat and seated row benches) (4 ) T.
SM 80 Unpacking & Assembly Instr uctions 21 Hardware Figure 5. Weight stack rubber bumpers. W . W eight s tack rubber bum pers (inserted under weight stac ks ) Hardware Figure 6.
SM80 U npacking & Assembly Instructions 22 PA RTS LIST Part # ID Description Quantity Main components 1 2 3 4 5 6 7 8 Cubes Low row bench Lat bench Connecting beam Lat top Tr icep top 300 lb weigh.
SM 80 Unpacking & Assembly Instr uctions 23 0017-00101-1413 0017-00104-0368 0017-00103-0217 Pulley hardw are (installed) 1-3/4” Bolt Cap washer 3/8” Nyloc nut 0017-00101-1413 0017-00104-0313 0.
An important point after buying a device Life Fitness SM80 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Life Fitness SM80 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Life Fitness SM80 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Life Fitness SM80 you will learn all the available features of the product, as well as information on its operation. The information that you get Life Fitness SM80 will certainly help you make a decision on the purchase.
If you already are a holder of Life Fitness SM80, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Life Fitness SM80.
However, one of the most important roles played by the user manual is to help in solving problems with Life Fitness SM80. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Life Fitness SM80 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center