Instruction/ maintenance manual of the product 8245102 Life Fitness
Go to page of 17
Part # 6870101 Revision:01/24/00 1 8245102 LEG PRESS/CALF ASSEMB LY INSTRUCTIONS.
IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8245 LEG PRESS/CAL F . Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
3 PARTS LIST PART # 6802903 6804803 6803802 6780703 6801703 6804102 6803503 6781303 6802002 6803203 6791102 6805101 6523401 6807401 3116101 6284501 6714601 3203501 6808901 6692601 3108002 6809601 KE Y.
STEP 1: FIGURE 1 • LOOSE LY assemble LOWER CROSS SUPPORT (4) to the TOWER (1) using two 1/2 X 4 ” BOLTS (39), two 1/2 ” W ASHERS (40) and one 1/2 ” LOCK NUT (41).
STEP 2: FIGURE 2 • LOOSE LY assemble the FRAME (2) to the LOWER CROSS SUPPORT (4) using two 1/2 X 4 ” BOLTS (39), two 1/2 ” W ASHERS (40) and two 1/2 ” LOCK NUTS (41). See FIGURE 2. • LOOSELY assemble the PIVOT FRAME (6) to the FRAME (2) using four 1/2 X 3 ” BOLTS (38), four 1/2 ” WASHERS (40) and four 1/2 ” LOCK NUTS (41).
STEP 3: FIGURE 3 6 • LOOSELY assemble the PIVOT FRAME (6) to the TOWER (1) using four 1/2 X 4 ” BOLTS (39), four 1/2 ” W ASHERS (40) and three 1/2 ” LOCK NUTS (41) as shown in FIGURE 3. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECUREL Y TIGHTEN THE FRAME CONNECTIONS IN THE FOLLOWING ORDER: 1 .
7 STEP 4: • Slide two 1-3/4 ” VINYL SLEEVES (22) over the shafts on the PIVOT ARM (7) as shown in FIGURE 4. • Slide one RUBBER BUMPER (21) over the short round tube on the PIVOT FRAME (6) as shown in FIGURE 4.
8 FIGURE 5 STEP 5: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURE LY assemble the FOOTPL ATE (3) to the PIVOT ARM (7) using four 1/2 X 4 ” BOLTS (39), four 1/2” WASHERS (40), and four 1/2 ” LOCK NUTS (41) as shown in FIGURE 5.
STEP 6: 9 • SECURE LY assemble the HANDLE (10) to the FRAME (2) using two 1/2 X 3 ” BOLTS (38), two 1/2” WASHERS (40), and two 1/2 ” LOCK NUTS (41) as shown in FIGURE 6. • Apply two 2-1/2 X 9-1/2 ” NON-SKID STRIPS (19) a foot stance apart on the PIVOT FRAME (6) as shown in FIGURE 6.
• SECURELY assemble one PAD (12) to the FRAME (2) using two 3/8 X 3 ” BO LTS (34) and two 3/8 ” WASHERS (36) as shown in FIGURE 7. 10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 7 STEP 7: 3/8 X .
11 FIGURE 8 STEP 8: STEP 9: FIGURE 9 • Snap two WEIGHT PL ATE BUSHINGS (27) into the top of all twenty WEIGHT PL ATES (29) as shown in FIGURE 9. 27 29 30 3/8 X 1 ” BUTTON HEAD 34 3/8 X 3 ” 9 37 20 24 36 12 2 • SECURE LY assemble the SE AT PAD (12) to the SEAT ADJUST (9) using two 3/8 X 3 ” BOLTS (34) and two 3/8 ” WASHERS (36).
0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 12 FIGURE 10 STEP 12: • Insert two GUIDE RODS (13) into the base of the TOWER (1) as shown in FIGURE 10. Lubricate the GUIDE RODS (13) with a slicon or teflon spray that is available at most hardware stores. • Slide two RUBBER BUMPERS (21) down over the GUIDE RODS (13).
13 FIGURE 12 • Place TOWER BRACE (8) over the GUIDE RODS (13) and SECUREL Y assemble TOWER BRACE (8) to TOWER (1) using two 1/2 X 4 ” BOLTS (39), two 1/2” WASHERS (40), and two 1/2 ” LOCK NUTS (41) as shown in FIGURE 12.
14 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 13 • Route the swivel end of the CABLE (14) through the holes and around the pulleys in the TOWER BRACE (8) as shown in FIGURE 13.
FIGURE 15 15 STEP 15: • SECURELY assemble two 4-1/2 ” PULLEYS (21) to the brackets on the FRAME (2) using three 3/8 X 2 ” BOLTS (32), one CABLE RETAINING CLIP (25), and three 3/8 ” LOCK NUTS (37) as shown in FIGURE 16. (NOTE: Position the CABLE RETAINING CLIP before tightening.
• Screw the threaded end of the CABLE (14) approximately 3/4 ” into the end of the 20 HOLE SELECTOR SHAFT (16) and tighten jam nut securely. See FIGURE 17. • If the HEAD PL ATE (17) does not sit on top of the first WEIGHT PL ATE (29), push the head plate down, insert the SELECTOR PIN (23) and perform several repetitions on the machine.
• SECURE LY assemble the SHROUD (11) to the TOWER (1) using four 3/8 X 1 ” BUTTON HEAD CAP SCREWS (30) as shown in FIGURE 18. FIGURE 18 17 STEP 18: Thank you for purchasing the LifeFitness 8245 LEG PRESS/CAL F .
An important point after buying a device Life Fitness 8245102 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Life Fitness 8245102 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Life Fitness 8245102 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Life Fitness 8245102 you will learn all the available features of the product, as well as information on its operation. The information that you get Life Fitness 8245102 will certainly help you make a decision on the purchase.
If you already are a holder of Life Fitness 8245102, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Life Fitness 8245102.
However, one of the most important roles played by the user manual is to help in solving problems with Life Fitness 8245102. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Life Fitness 8245102 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
