Instruction/ maintenance manual of the product E2241S LG
Go to page of 39
www .lg.com O WNER’S MANU AL L CD MONIT OR L CD MONIT OR MODEL E19 41T E19 41S E204 1T E204 1S E22 4 1T E22 41S E234 1T E2 44 1T P l ea s e re a d th i s ma n u a l ca r e fu l l y b e for e op e r a t i n g yo u r se t a n d re tain it f or futur e ref erenc e.
1 This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Important Precautions 3 On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching.
4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor . If any items are missing, contact your dealer . User's Guide/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.
Connecting the Display 5 Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand (A type) 1. Place the monitor with its front facing downward on a soft cloth.
6 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 3. Remove the Stand Body and Stand Base from product in correct direction as shown in the picture . 2. Place the monitor face Down on the cushion or soft cloth.
7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand (B type) 1. Place the monitor with its front facing downward on a soft cloth.
8 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 3. Nip Latch inside,Take off the stand base from stand body.
9 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand (C type) 1. Place the monitor with its front facing downward on a soft cloth.
10 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 3. To disconnect the Stand Base from the Stand Body ,simply unfold the screw handle and turn"counter-clockwise" to loosen the screw and disconnect the Stand Base from its body.
11 Connecting the Display Before setting up the monitor , ensure that the power to the monitor , the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below . 1. Adjust the position of the panel in various ways for maximum comfort.
12 NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.
13 Connecting the Display E1941S/E2041S/E2241S NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.
14 Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear.
15 Control Panel Functions AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO button on the MONITOR SETUP OSD. ( Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).
16 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.
17 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. : D-SUB(Analog signal) input : DVI-D(Digital signal) .
18 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description To adjust the brightness of the screen. Change the input image signal ratio to original. WIDE ORIGINAL Switch to full screen mode according to input image signal. * This function works only if input resolution is lower than monitor ratio (16:9).
19 On Screen Display(OSD) Selection and Adjustment Main menu Description To choose the language in which the control names are displayed. Press the , buttons to reset immediately. Restore all factory default settings except "LANGUAGE." To adjust the contrast of the screen.
20 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual.
21 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description Exit : Exit , : Move : Select another sub-menu Turn on the SUPER ENERGY SAVING fuction. When current setting value is ON,the SUPER SAVING color is green. Turn off the SUPER ENERGY SAVING function.
22 On Screen Display(OSD) Selection and Adjustment SUPER SAVING LED SAVING 19 inch 3 3 3 18 4 15 5 12 5 17 20 inch 22 inch 23 inch 24 inch Saving Data depends on the Panel. So,those values should be different from each panel and panel vendor. LG accumulate those values using integrated function with 10 minutes broadcast video signal.
23 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display co.
24 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO button to automatically adjust your display image to the ideal setting.
25 Display image is incorrect T roubleshooting ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot.
26 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.0 cm 0 . 300 mm x 0 . 300 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 61 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
27 Specifications E1941S 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.0 cm 0 . 300 mm x 0 . 300 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 61 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
28 Specifications E2041T 50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50.8 cm 0 . 2766 mm x 0 . 2766 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
29 Specifications E2041S 50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50.8 cm 0 . 2766 mm x 0 . 2766 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
30 Specifications E2241T 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6 cm 0 . 248 mm x 0 . 248 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
31 Specifications E2241S 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6 cm 0 . 248 mm x 0 . 248 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
32 Specifications E2341T 58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 58.4 cm 0 . 265 mm x 0 . 265 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
33 Specifications E2441T 60.97 cm (24 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 60.97 cm 0 . 277 mm x 0 . 277 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
34 Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode E2041T/E2041S 1 2 3 4 5 6 7 8 *9 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1600 x 900 31.468 31.469 37.500 37.879 46.875 48.
Specifications 35 Indicator On Mode Sleep Mode Off Mode Blue Blue Blinking Off LED Color MODE Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq.
1. Place the monitor with its front facing downward on a soft cloth. 36 Installing the W all mount plate This monitor satisfies the specifications of the W all mount plate or the interchange device. A type 2. Remove the Stand Body and Stand Base from product in correct direction as shown in the picture .
37 Installing the W all mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.
M a k e s u r e to r e a d t h e Sa fe t y P r e c a u t i o n s befor e using the product . K e e p t h e O W N E R ’ S M A N U A L (C D ) i n a n acces sible place f or furture ref erence. The mod el a nd se ria l nu mbe r of the SET is located on the back o r one s ide of t he SET .
An important point after buying a device LG E2241S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought LG E2241S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data LG E2241S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, LG E2241S you will learn all the available features of the product, as well as information on its operation. The information that you get LG E2241S will certainly help you make a decision on the purchase.
If you already are a holder of LG E2241S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime LG E2241S.
However, one of the most important roles played by the user manual is to help in solving problems with LG E2241S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device LG E2241S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
