Instruction/ maintenance manual of the product ST-1000 Keys Fitness
Go to page of 32
O O W W N N E E R R ’ ’ S S O O W W N N E E R R ’ ’ S S M M A A N N U U M M A A N N U U A A L L A A L L Questions? Call our toll free Keys Fitness Helpline 1-800-683-1236 ST-1000 H OME G YM.
V THANK Y OU for making this Strength T rainer unit a part of your exercise program. Keys Fitness and our Strength T rainer Series assures the very best in value, appearance, durability and biomechanics. This manual will guide you through the assembly process.
BEFORE Y OU ST ART Prior to assembly , remove components from the box and verify that all the listed parts were supplied. Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems.
PA R T S Y.
PA R T S Z.
[ PA R T S.
PA R T S .
P ARTS LIST ] # DESCRIPTION QTY 1 Base Frame 1 2 Foot Plate 1 3 Main Upright 1 4 Rear Cross Beam 1 5 Rear T op Beam 1 6 Main T op Beam 1 7 Foot Plate Bracket 1 8 Lat Pull Down Bar 1 9 Seat Pad Support.
ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. ^ Do not use bolt here yet. W ait for STEP 6. Do not use bolt here yet.
u ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
` ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. a Feed Cable (63) through framework as pictured. Hold cable in place by placing in pulley grooves and bolting pulleys to frame.
ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. 11 First, insert guide rods into rear cross beam (4). Then slide on, from top to bot- tom, rubber bushings (125), 19 weight plates (128) and weight plate assembly (50).
12 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
13 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
14 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
15 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Hex Screws (109) are already pre-assembled for you. Make sure to unscrew them before sliding in shafts (43).
16 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Note: Hex screws (109) are already pre-assembled for you. Make sure to uncrew them before sliding in shaft(39).
17 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Note: Hex screws are already pre-assembled for you. Make sure to unscrew them before sliding in shaft (39).
18 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
19 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
20 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
21 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
22 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
ASSEMBL Y 23 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 24 Feed cable (62) through framework as pictured. Hold cable in place by setting in pulley grooves and bolting pulleys to frame or as pictured. View finished assembly of this step in future steps or on cover page for guidance.
24 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Feed remaining section of cable (63) through leg press framework.
25 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Feed cable (64) through framework. Hold cable in place by setting in pulley grooves and bolting pulleys to frame.
26 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
27 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Before securing weight stack covers (25,26): 1. Make sure to lightly lube the guide rods with the supplied lubrication. 2. Place the weight stack plate numbers on the weight plates.
28 EXPL ODED VIEW.
KEY S FITNESS PRODUCTS, L.P . STRENGTH TRAINER SERIES LIFETIME WARRANTY This W arranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Ke ys”) under the KEYS brand name. The warranty period to the original purchaser is lifetime of the original purchaser .
Keys Fitness Products, L.P . 4009 Distribution Drive, Suite 250 Garland, T exas 75041 Customer Service: 1-800-683-1236.
An important point after buying a device Keys Fitness ST-1000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Keys Fitness ST-1000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Keys Fitness ST-1000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Keys Fitness ST-1000 you will learn all the available features of the product, as well as information on its operation. The information that you get Keys Fitness ST-1000 will certainly help you make a decision on the purchase.
If you already are a holder of Keys Fitness ST-1000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Keys Fitness ST-1000.
However, one of the most important roles played by the user manual is to help in solving problems with Keys Fitness ST-1000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Keys Fitness ST-1000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
