Instruction/ maintenance manual of the product EVE-1500 Impex
Go to page of 31
NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Pack Assembly Instruc tion Parts L ist Resistance Chart Warranty Ordering Parts Model.
TA BLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFET Y NOTICES...................................................................……….. 2 HARDW ARE PACK……….
IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assemble or operate your machine.
WA RNING LA BEL REPLA CEMENT The w arning labels show n here h ave been p laced on th e Left Base Frame an d Right Up per Frame. If the labels are missing or illegible, please call customer service at 1- 800-999-8899 for replacement s. A pply the labels in location shown.
HA RDWA RE PA CK 4.
HA RDWA RE PA CK 5.
HA RDWA RE PA CK 6.
A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended tw o or more people assembling this machine to avoid possible injury . STEP 1 (See Diagram 1) A.) Place the Right and Left Base Frames (#1 & #14) on a flat surface.
STEP 2 (See Diagram 2) A.) Insert two Guide Rods ( #12) into the holes on the Gui de Rod Base (#10). Secur e each Guide Rod w ith one M10 x ¾” Al len Bolt ( #80) and Ø ¾” W a sher (#94) from the bottom. B.) Attach the Guide Rod Base to the Left and Right Base Frames (#1 & #14) .
STEP 3 (See Diagram 3) A.) Attach the Right Ver tical Beam ( #3) onto the Rig ht Base Frame (#1). Secure it w ith two M 10 x 2 ½” Carri age Bolts ( #87), Ø ¾” W ashers (#94), and M10 Ai rcraft Nuts (#97). B.) Attach the Left Vertical Beam (#17) onto the Left Base Frame (#14).
DIAGRAM 3 10.
STEP 4 (See Diagram 4) A.) Slide nineteen W eight Plates (#59) onto the Gui de Rods (#12). M ake sure the gr ove on the Plates all face tow ard front of the machine. Insert the Selector Rod ( #13) into the center hole. It is str ongly recommended to spray lubri cant such as W D-40 on the two Gui de Rods to minimi ze fric tion.
DIAGRAM 4 12.
STEP 5 (See Diagram 5) A.) Attach the Right Seat Support (#2) onto the Right Base Fr ame (#1). Secure it wi th one M10 x 2 ½ ” Carriage Bol t (#87), Ø ¾ ” W asher (#94), and M10 Airc raft Nut (#97). B.) Attach the Right Seat Support (#2) to the Rig ht Vertical Beam ( #3).
STEP 6 (See Diagram 6) A.) Attach the Left Seat Support (#15) to the Left Base Frame (#14). Secure it w ith one M10 x 2 ½”Car riag e Bolts (#87), Ø ¾ ” W asher (#94), and M10 Air craft Nut (#97). B.) Attach the Left Seat Support to the Lef t Vertical Beam (#17).
STEP 7 (See Diagram 7) A.) Align the Front Press Base ( #19) to the Left Upper Frame (#18) . Insert a 6” Axle (#52) through the holes and secure it w ith two Ø ¾” W ashers (#94) and M10 Ai rcraft Nuts (#97) . B.) Insert the axle on the Left Butterfly ( #20) through the hol es on the Front Press Base.
Cable Loop Diagram 16.
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach one end of the 118” Butterfly C able (#42) to the hook on the R ight Butter fly (#21) . Draw the Cable to the right open Sw iv el Pulley Bracket (#26). B.) Attach a Pulley (#60) to the Br acket.
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the end of the 115” Front Press Cable (#43) to the open bracket on the Left Vertical Beam ( #17). Secure it with one M 10 x 1” Allen Bolt ( #81), tw o Ø ¾” W ashers (#94), and one M10 Ai rcraft Nut ( #97).
DIAGRAM 9 19.
STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Attach the 180” Upper Cable (#40) to the f ront opening on the Ri ght Upper Frame (#4). B.) Place a Pulley ( #60) to the opening and secur e it with one M10 x 2 3/8” Allen Bolt (#84), two Pull ey Bushi ngs (#78) , and one M10 Airc raft Nut (#97).
STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 105” Lower Cabl e (#41) to the openi ng on the bottom of Leg Dev eloper (#7). B.) Attach a Pulley (#60) to the opening. Secure i t wi th one M10 x 2 3/8” Allen Bol t (#84), tw o Pulley Bushings ( #78), and one M10 Ai rcraft Nut (#97) .
STEP 12 (See Diagram 12 & Cable Loop Diagram) A.) Attach one end of the 276” Leg Press Cable (#44) to the open bracket underneath the Left Seat Support (#15). Secure it with one M 10 x 1” Allen Bolt ( #81), tw o Ø ¾” W ashers (#94), and one M 10 Aircr aft Nut (#97).
DIAGRAM 12 23.
STEP 13 (See Diagram 13) A.) Attach a Backrest Board (#38) to the Ri ght Verti cal Beam (#3). Secur e it with tw o M8 x 2 1/8” Al len Bolts (#89) and Ø 5/8” W ashers (#93). B.) Attach a Seat Pad (#37) onto the Rig ht Seat Support (#2). Secur e it w ith tw o M8 x 2 1/8” Allen Bol ts (#89) and Ø 5/8” W ashers (#93).
STEP 14 (See Diagram 14) A.) Attach a Backrest Board (#38) to the Left Vertical Beam ( #17). Secure it with tw o M8 x 2 1/8” Al len Bolts (#89) and Ø 5/8” W ashers (#93). B.) Attach a Seat Pad (#37) onto the Left Seat Support (#15). Secure it w ith two M8 x 2 1/8” Allen Bol ts (#89) and Ø 5/8” W ashers (#93).
STEP 15 (See Diagram 15) A.) Attach the W eight Stack Cov er (#29) to the Gui de Rod Upper Fr ame (#11) and Guide R od Base (#10). Secure i t wi th four M10 x ¾ ” Allen Bolt s (#80) and Ø ¾” W a shers (#94).
STEP 16 (See Diagram 16) A.) Connect the Lat Bar (#5) to the 180” Upper Cable (#40) wi th two C -clips ( #75) and a Short Chain (#74) . Store the Lat Bar onto the hooks on the Ri ght Upper Frame. B.) Connect the Abdominal Strap (#99) to the C able Head Connector (#45) w ith a C-clip.
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Right Base Fram e 1 2 Right Seat Support 1 3 Right Vertical Beam 1 4 Right Upper Fram e 1 5 Lat Bar 1 6 Arm Curl Stand 1 7 Leg Developer 1 8 Arm Curl Handle 1 9.
EVE-1500 Weight Resistance Chart WEIGHT FRONT LOW LAT BUTTERFLY AB LEG PLATE PRESS PULLEY BAR STATION STATION PRESS 1 25 30 30 15 30 30 2 35 40 40 20 40 45 3 45 50 50 25 50 60 4 55 60 60 30 60 75 5 65.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be f ree from def ects in work m ans hip and m aterial, under norm al use and s ervic e conditions , f or a per iod of two years on the F ram e f r om the date of purchase.
An important point after buying a device Impex EVE-1500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Impex EVE-1500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Impex EVE-1500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Impex EVE-1500 you will learn all the available features of the product, as well as information on its operation. The information that you get Impex EVE-1500 will certainly help you make a decision on the purchase.
If you already are a holder of Impex EVE-1500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Impex EVE-1500.
However, one of the most important roles played by the user manual is to help in solving problems with Impex EVE-1500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Impex EVE-1500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
