Instruction/ maintenance manual of the product PFG-691 Henny Penny
Go to page of 11
Model 691 This section provides the installation and unpacking instructions for the Henny Penny PFG-691. Installation of this unit should be performed only by a qualified service technician. Do not puncture the fryer with any objects such as drills or screws as electrical shock or component damage could result.
Model 691 7 . Remove the counterweights, which are strapped to the pallet under the fryer , from the pallet. Do not drop. The counterweights weigh approximately 18 lbs. (8.1 kg) each. Handle with care, or personal injury could result. 8 . Remove rear service cover .
Model 691 Optional Ramp Unloading 803 2- 3.
Model 691 2-4 90 8.
Model 691 2-3. SELECTING THE FR YER The proper location of the fryer is very important for operation, LOCA TION speed, and convenience. Choose a location which provides easy loading and unloading without interfering with the final assembly of food orders.
Model 691 2-5. VENTILA TION OF FR YER The fryer should be located with provision for venting into adequate exhaust hood or ventilation system. This is essential to permit efficient removal of the flue gases and frying odors. Special precaution must be taken in designing an exhaust canopy to avoid interference with the operation of the fryer .
Model 691 2-7. GAS PIPING • The fryer must be isolated from the gas supply piping (Continued) system by closing its manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.
Model 691 2-8 80 3 2-7. GAS PIPING (Continued).
Model 691 2-8. GAS PRESSURE The gas pressure regulator on the gas control valve is REGULA T OR SETTING factory set as follows: Natural: 3.5 inches water column (0.87 kPa) Propane: 10.0 inches water column (2.49 kPa) MAKE SURE GAS PRESSURE IS SET COR- RECTL Y .
Model 691 2-10. TESTING THE FR YER Each Henny Penny pressure fryer was completely checked and tested prior to shipment. However , it is good practice to check the unit again after installation. 2-1 1. GAS LEAK TEST Prior to turning the gas supply on, be sure the gas control valve knob on the gas control valve is in the OFF position.
Model 691 BOIL-OVER PREVENTION IN HENNY PENNY FRYERS F AILURE T O FOLLOW THESE INSTRUCTIONS CAN RESUL T IN SHOR TENING OVERFLOWING THE FR YPOT WHICH COULD CAUSE SERIOUS BURNS, PERSONAL INJURY , FIRE, AND/OR PROPERTY DAMAGE. • THE SHOR TENING MA Y BE STIRRED ONL Y DURING THE MORNING ST AR T -UP PROCEDURE.
An important point after buying a device Henny Penny PFG-691 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny PFG-691 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny PFG-691 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny PFG-691 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny PFG-691 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny PFG-691, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny PFG-691.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny PFG-691. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny PFG-691 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
