Instruction/ maintenance manual of the product OG-30X Henny Penny
Go to page of 154
.
Henny Penny Model OE/OG 301/302/303.
Henny Penny LIMITED W ARRANTY FOR HENNY PENNY APPLIANCES Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Pe.
This manual should be retained in a convenient location for future reference. Wiring diagram for this appliance is located on the inside access door below the control panel. Post in a prominent location, instructions to be followed in event user smells gas.
ode1 Nominal Heat Input: (Net) Nominal Heat Input: (Gross) Supply Pressure: Test Point Pressure: Injector Size: Natural (I& = 2 1,l KW (72,000 B tu/h) Liquid Propane (I& = 21,l KW (72,000 Btu/.
Section Page Section 1. INTRODUCTION ..................................................... l-l l-2. Model Variations ................................................ l-l l-3. Features ....................................................... l-l l-4. Safety .
se~tio age Section6. MAINTENANCE...................................................... 6-l 6-l. 6-2. 6-3. 6-4. 6-5. 6-6. 6-7. 6-8. 6-9. 6-10. 6-11. 6-12. 6-13. 6-14. 6-15. 6-16. 6-17. 6-18. Introduction ................................................
em 1-2. NS The Henny Penny Open Fry Station is a basic unit of food equipment designed to cook foods better and easier. The microcomputer based design helps make this possible. This manual covers the following variations of the Henny Penny Open Fry Station: Model OG-301/302/303 (gas model) Model OE-301/302/303 (electric model) 0 Easily cleaned.
The word WARNING is used to alert you to a procedure that if not performed properly, might cause personal injury. The word CAUTION is used to alert you to a procedure that, if not performed properly, may damage the fry station. The word NOTE is used to highlight especially important information.
enny This section provides the installation instructions for the Henny Penny Fry Station. Installation of the unit should be performed only by a qualified service technician. Do not puncture the unit with any objects such as drills or screws as component damage or electrical shock could result.
The proper location of the Fry Station is very important for operation, speed, and convenience. The location of the fiy station should allow clearances for servicing and proper operation. Choose a location which will provide easy loading and unloading without interfering with the final assembly of food orders.
When installing the gas fry station do not attach an exten- sion to the gas flue exhaust stack. This may impair proper operation of the burner, causing malfunctions and possible negative back draft. The gas fry station is factory available for either natural or propane gas.
T INIMU~I PULL of equip- ment away from wall permissible for accessi- bility to Quick Disconnect Device. AVOID SHARP BENDS AND KINKS when pulling equipment away from wall. (Max- imum pull will kink ends, even if installed properly, and reduce Connector life.
A standard one inch, black steel pipe and malleable fittings should be used for gas service connections. Do not use cast iron fittings. Although one inch size pipe is‘reconunended, piping should be .
The following steps provide the pilot PROCEDURE lighting procedure: 1. Open doors and open gas shut-off valve. (see illustrations) 2. The gas cock dial has a dual function: a. Complete control of gas to the pilot and main burner. b. When in the pilot position, it is the reset mechanism for the automatic pilot.
Depress lightly and turn manual lever on gas valve to the OFF position. The gas pressure regulator on the automatic gas valve is factory set as follows: @ Natural: 3.5 inches water column. * Propane 10 0 inches water column. e 120 V, 50/60 Hz., 12 A, 1 PH 0 230 V, 50/60 HZ.
I The OE-301/302/303 is available from the factory wired 208, or 220/240 volts, 50 or 60 hertz source. Refer to the table below for supply wiring and fusing. Volts Phase KW Amps 208 3 11.25 31 208 3 13.50 38 220/240 3 11.25 30132 2201240 3 13.50 33135 400 3 11.
odel 301/302/303 This section provides operating procedures for the Henny Pen- ny OG/OE-301/302/303. Sections 1, 2, and 3 should be read and all instructions should be followed before operating the fryer. 3-2. Figures 3-1 through 3-8 identify and describe the function of all operating controls and components.
Melt LED Ready LED Head LED Product LED Time LED Temperature LED Alarm LED When the melt LED is flashing, the fryer is in the melt cycle. When the temperature of the shortening reaches approximately 250°F (121”C), the melt LED will go off and automatically switch to the heat cycle.
3-l 3-2 3-2 3-3 3-3 &I -;j tern No. 14 15 16 17 18 19 20 I escriptiori Other LED Idle LED Up and Down Switches Fuses (electric only) High Limit Reset Contactors (electric only) Thermal Sensor The other LED flashes while in the high level program mode and special program modes only.
3-6 24 Drain Interlock (Hidden behind bracket) Drain Valve Filter Union odel The drain interlock switch is a microswitch that provides pro- tection for the heating elements in the event an operator drains shortening from the frypot while the power switch is on.
odd 0 301/302/303 Fig. NO. 3-6 3-6 3-8 3-8 Rte No. 25 Filter Drain Pan 26 Filter Pump Switch 27 Oil Return Line 28 Gas Shut-Off Valve Each cookpot has its own gas shut-off valve on thegas line (gas only) going to the gas valve. 29 30 Gas Control Valve (gas only) Gas Solenoid (gas only) Function The .
Y el 0.
0 . %.
Y 3 re 3- re.
ode! 0.
Main Power Switch The main power switch is a two,way switch. Move the switch to the position marked ON to operate the fryer. Move the switch to the position marked ON to operate the The thermostat is an electro-mechanical device used to below the temperature set by the thermostat.
It is recommended that a high quality frying shortening be used in the O&301/302/303 and OG-301/302/303 fry stations. Some low grade shortenings have a high moisture content causing foaming and boiling over. The Henny Penny OE-301/302/303 requires 48 pounds of shortening per cookpot.
4. ove power switch to the “ON” position. Unit will automatically go into the melt cycle. When the ri,~ :%; : :. ,$‘,, ‘>, temperature reaches 250°F (121OC) the control will go into the heat cycle. The shortening will be heated until the temperature setting is reached.
el 0 Frying breaded food requires frequent filtering. Taste the cold shortening every day for flavor. Watch the shortening for foaming during the frying cycle. Discard the shorten- ing as soon as it shows sign of foaming. Clean the cookpot as follows each time the shortening is changed or filtered.
enny OEI 301l3~2l303 3-5. F (~o~ti~ue~) If shortening is slow coming from faucet, it is possible that the filter connecting the union on the filter tube line is not tightened properly. If so, turn off the pump and use gloves to tighten the union. This union will be hot.
The filter pump motor is equipped with a manual reset but- ton in the event the motor’s thermal protector acuates. This reset button is located on the rear of the motor. Wait ap- proximately 5 minutes before attempting to reset this pro- tector device.
3-8. 8. Clean the top and bottom filter screen with soap and water. Rinse thoroughly with hot water. Be sure that the filter screens, crumb catcher, filter clips and the suction standpipe are thoroughly dry before assembly of filter envelope or water will dissolve the filter paper.
odel 301 l3~2l3Q3 After the initial installation of the fryer, as well as .before every change of shortening, the cookpot should be thoroughly cleaned as follows: I Melt bypass should be in operation. Refer to section 3-2 “Operating Controls” on Exit Melt Switch.
6. When the solution reaches 200”F, turn the main power switch to the OFF position. Watch cleaning solution constantly to make sure it does NOT boil over, causing damage to controls. 7. Let the cleaning solutions stand for 15 to 20 minutes with the power off.
The controls have four programming levels, a first level mode, a second level mode, a third level mode, and a special program mode. In each level, pressing the set switch advances through the programmable items. Program mode can be entered at anytime except during an alarm.
7. Press the set switch and the alarm LED flashes. The left display shows “AL 1”) the right display shows the alarm time and can be adjusted with the right Up and Down Switches. 8. Repeat step 8 for alarms 2,3, and 4. 9. Press and hold the Set Switch to exit program mode, or continue to second level mode.
4-3. I ING 8. Also, with the Product LED flashing, pressing the right Up and Down Switches will access the Idle Mode parameters. The idle LED will be flashing, the left display will continue to show “Slct” and the right display shows “Prod.” Pressing the Set Switch allows the operator to program the idle parameters (See Section 4-3).
el 30113Q21303 3. Press the Set Switch and the left display flashes “Prob” and “Calib.” The right display shows the actual pot temperature, and the right Up and Down Switches are used for calibration. 4. Press the Set Switch and the left display flashes “AL” and “dur.
This section provides troubleshooting information in the form of an easy-to-read table. If a problem occurs during the first operation of a new fryer, recheck the installation per Section 2 of this manual. Before troubleshooting, always recheck the operating procedure per Section 3 of this manual.
NG LE With switch in POWER position and switch light not illuminated, fryer is complete ly inoperative. With switch in power position, switch light is on, but all other lights are out ex cept the pump will operate. Shortening will not heat but lights are on.
Shortening will not heat, but lights are on. A. Pilot will not light (gas model) B. Pilot will not stay lit. C. Burner will not light, pilot li (gas model) Faulty Contactor (elec.
5-2. T LES NG (Continued) _% Heating of Low or improper shortening too voltage (elec. slow model) Heating of shortening too slow (elec. model Shortening overheating Weak or burnt out elements (elec.
odel Foaming or boil- ing over of shortening. Shortening will Drain valve not drain from clogged with frypot crumbs Filter motor rum but pumps shortening slowly Filter switch ON motor does not run .
.
6-1. ENTS This section provides procedures for checking and replacement of the various parts used within the unit. Before replacing any parts, refer to Section 5, Troubleshooting. It will aid you in determining the cause of a particular malfunction. You may want to use two test instruments to check the elec- tric components.
6-3. E EL (~~~ti~~ed) 2. Using a Phillips head screwdriver, remove the four screws securing the control panel to the unit, and let panel swing down. The panel is hinged to hang in this position for convenience. 3. Disconnect nine-pin connector and remove probe connec- tion from control panel.
Disconnect power supplied to the unit by unplugging the power cord, or turning off the wall circuit breaker, or fuse. Be aware that the other controls will HAVE power on electric models, or electrical shock could result. 2. Swing control panel down per section 6-3.
6-5. This high temperature control is a manual reset control which senses the temperature of the shortening. If the shortening temperature exceeds the safe operating limit, this control switch will open and shut off the heat to the frypot. When the temperature of the shortening drops to the safe operating limit, the control must manually be reset.
Before following these steps, place POWER switch to the OFF position, and unplug the power cord or open the wall circuit breaker, or electrical shock could result. Be aware that the other controls will HAVE power. 1. If the tube is broken or cracked, the control will open, shut- ting off electrical power.
6-5. Be sure capillary bulb of high limit is located behind front edge of elements. Capillary bulb and bulb holders should be posi- tioned as not to interfere with basket or when cleaning the frypot wall, or damage to capillary tube could result. 15. With excess capillary line pulled out, tighten smaller nut.
213 5. Remove probe as described in section 6-4. 6. Loosen small inside screw nut on capillary tube. 7. Remove capillary bulb from bulb holder on inside of frypot. 8. Remove larger outside screw nut that threads into “Y” fitting. 9. Cut the capillary bulb on the inside of cookpot, and remove the capillary from unit.
Heating elements are available for 208 and 230 voltage. Check data plate to determine the correct voltage. If the shortening’s temperature recovery is very slow or at a slower rate than required, this may indicate defective heating element(s). An ohmmeter will quickly indicate if the elements are shorted or open.
enny 7. Remove the heating elements from the frypot as a group by lifting the far end and sliding them up and out toward the rear of the frypot. Always install new rubber 0 rings (2) when installing heater elements.
ode -8. ELS) PRIMARY CONTACTOR 30 31 32 Each electric fryer requires two switching contactors. One is the primary contactor and the second in line is the heat con- tactor. When open, the primary contactor allows no power to flow to the heat contactor.
The following checks are performed with the wall cir- cuit breaker closed and the main power switch in the “ON” position. Extreme caution should be taken. Make connections before applying power, take reading, and remove power before removing meter leads, or elec- trical shock could result.
6-8. NT s 4. Connect the labeled wires to their respective positions. 5. Install the control panel per section 6-3. 6. Reconnect power to the fryer and test the fryer for proper operation.
6-9. ASS ) 1. Remove the control panel per section 6-3. 2. Open doors to bottom of unit. 3. Remove the flexible conduit from the heat shield and shroud which contains the wires of the gas valve and solenoid. 4. Disconnect gas supply line from connector at gas valve.
GASCONTROL 318 TO 112 INCH PILOT The thermocouple controls the gas valve. It generates voltage in the millivolt. This voltage signals the gas control valve to remain open to the pilot and burner. When the voltage is not generated the gas valve will shut off, not allowing gas to the pilot and main burner.
DIAL REFERENCE PorN? GAS MAGNETIC REGYLATOR The gas control valve regulates the flow of gas to the pilot and the main burner. The valve consists of: gas regulator, magnetic plug, pilot gas tube, gas cock dial, pilot adjustment cap and screw, gas outlet and inlet ports, thermocouple con- nector, and electrical connection.
tep 2 4. Remove the 90° connector and conduit from the old gas valve and install on the replacement gas valve. 5. Remove the four screws securing the operator and gasket. 6. Secure the new operator and gasket with the four screws provided. 7. Reconnect the gas valve wires.
PILOT THERMOCOUPLE The following two procedures must be performed with the gas supply reconnected and turned on. The service cord must be plugged into the receptacle and the cir- cuit breaker on. 1. The pilot burner is preset at the factory. It may require resetting at the time of installation.
ode The electric fryers have two 15 amp fuses to protect the cir- cuitry, and two 15 amp fuse to protect the PC board, for each control panel, found behind doors, up under shroud. The gas units do not have fuses other than at the main power source. Each PC board has a 1.
All-model fryers have a drain microswitch in line with the gas valve or heat contactor. When the drain valve is opened to drain the shortening, this causes the drain switch to open, shut- ting down the gas to the burners or electrical power to elements.
The Power Switch is a two way rocker switch. With the switch in the “ON” position, this energizes the controls. 1. Remove power supplied to the unit, or on electric models, to the cookpot to be worked on. Disconnect power supplied to the unit by unplugging the power cord, or turning off the wall circuit breaker or fuse.
The filter switch is a two way rocker switch with the switch in the “ON” position, the filter motor energizes to pump up the shortening from the drain pan. 1. Remove power supplied to the unit, or on electric models, to the far right cookpot that powers the filter switch.
ny ode! The filtering system consists of the motor and filter pump assembly, filter screen assembly, and tubing. The two most common causes for a fryer’s inability to pump shortening is that the pump is clogged with breading or solid shortening has cooled and solidified in the lines and pump.
ova 1. If the pump needs to be replaced, loosen one inch nuts from the outflow and inflow lines. Then remove the two bolts holding the pump to the motor with a l/2 inch wrench. 2. The shaft seal should remain on the motor shaft, or if leak- ing, could be replaced at this time.
eset” 4. To replace the pump and motor assembly, insure the main power has been removed from the fryer. Before starting this procedure move MAIN POWER SWITCH to OFF position. Disconnect main circuit breaker at the main circuit breaker box and unplug ser- vice cord from wall receptacle, or electrical shock could result.
ode ~I3021303 vice Gas model fryers are factory available for either NATURAL GAS or PROPANE GAS. Factory conversion kits for natural gas and propane gas are available that require the burner jets, pilot jet and regulator assembly to be changed.
Before starting this procedure move MAIN POWER SWITCH to OFF position. Disconnect main circuit breaker at the main circuit breaker box and unplug ser- vice cord from wall receptacle, or electrical shock could result. To convert from one type of gas to another the following pro- cedure may be followed: 1.
318TO 112 INCH PILOT ace 13. Check for gas leak at the gas control valve and main gas valve per step 11 of this section, If there are no leaks, eon- tinue to step 14. If a leak is detected, shut off gas valves and repair leak. Escaping gas could cause an explosion, and personal injury and property damage could result.
Y 297.
n . - ;: < c 297.
ode1 5 I------- ___------------ ----------1 I I I I I I I I I I I I I I I I I I I ITRANSFORMER SWITCH I I L I PlOP9 P8 P7 P6 P5 P4 P3 P2 Pl I L PANEL I I ------- __----- -- I i __---------- ----- -I- - CAP.
I I I I I I I I I I I I I I I I I I I POWER SW I TCH -.
t I I I I I I I I I I I I I I I I I I TRANSFORMER 12ov POWER SWITCH I I Pl OP9 P8 P7 P6 P5 P4 P3 P2 PI - I I I I I I I I I ---- _---- --- --- L. YI L /-h--l 1 3 SVST 1PH CAP.
ode! I I I I I I I I I I I I I I I I THERMOSTAT I FRONT CONTROL PANEL --- -----____-----____ I I I I I I I I I I I I I I I I I I I 1 J - ----------------- -I ---_ WIRING DIAGRAM1 WIRING DIAGRAM) 54002.
odel ,__----------------------- ------- TIMER 1 I I I I I I I I I I I I I I I I I I I I THERMOSTAT ; Ii I I I I I I I I I I I I I I I I I I FRONT CONTROL PANEL I --- ------------------ 5 ‘2 I- c” z z I I I Y I- 1PH (SEE ABOVE FOR (SEE ABOVE FOR (SEE ABOVE FOR WIRING DIAGRAM1 WIRING DIAGRAM) WIRING DIAGRAM) .
I -rIMER - - - - - - - ' THERMOSTAT ] r I II I I’ I I I I I I I I I I I I I- I I I I I I I I I I I 220-240V 50/60HZ ‘“-‘3 J i 1 14 I IWIN i-KYtK #2 (SEE ABOVE FOR WIRING DIAGRAM) (SEE ABO.
1 THERMOSTAT I I I I I I I I I I I I I I I I I I I I I I I I I I I I I ------------------_________ ----- -+ SYS T - 12OV 50/60HZ 1PH I (SEE ABOVE FOR WIRING DIAGRAM) I -36.
ode1 I --------__ --------_-_ ------------ l I I T I I I I I I I I I I I I I I I I I I I I MER I I I I I I I I I I I I I I I I I I I I I I TH L--- ‘ANFI FRONT CONTROL P.
ODEL OG-302 SYSTE 12OV 50/60HZ 1PH OPEN FRYER rl (SEE C-45325 FOR IRING DIAGRAM) OPEN FRYER #2 (SEE C-45325 FOR WIRING DIAGRAM1 45390.
el 3 I- I I I I I I I I I I I I I I - -----------------__----- -------- 12v 131 714 I - - - _ I I ITRANSFORMER 1 1 CONTROL lNPUT P6 I 110 la L - POWER SWITCH t I FRONT CONTROL PANEL 1.
46 -GND L3 L2 Ll OPEN FRYER #l (SEE C-33282 FOR WIRING DIAGRAM) I I PUMP OPEN FRYER #2 (SEE C-33282 FOR WIRING DIAGRAM) CAP./RES. ASSY 3 TE 208/24OV 3PH OPEN FRYER #3 (SEE C-33282 FOR WIRING DIAGRAM).
^. .^ II I GND II L3 L2 Ll LNLJ-II blUlJ I’ L3 25 I’ L3 L2 L2- Ll I 1 R-1 I ” ,32 --I I OPEN FRYER #2 (SEE C-33282 FOR WIRING DIAGRAM) OPEN FRYER #3 OPEN FRYER #l (SEE C-33282 FOR WIRING DIAGRAM.
OPEN FRYER #2 (SEE C-33282 FOR WIRING DIAGRAM) CAP. /RES. ASSY OPEN FRYER s3 (SEE C-33282 FOR WIRING DIAGRAM) 208/24OV 3PH.
GND L3 L2 Ll I 24 OPEN FRYER #l (SEE C-33282 FOR WIRING DIAGRAM) II PUMP 208/24OV 3PH OPEN FRYER #2 (SEE C-33282 FOR WIRING DIAGRAM1.
-----m-----m I I I I I I I I I I I I I I I I I I I I I I I HEAT E OUTPUT B F ~ANSFORMER I ,110 I I I I I I I I I I I I I POWER SW I TCH 27 124 I I ODEL OE-300 480V 3PH.
I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I DISPLAY BOARD P6 ; ----- I I lTRANSFORMER POWER- - SWITCH I I I I I I -I FRONT CONTROL PANEL 25 2C r L3 h 23 24 .
GND N L3 L2 L1 OPEN FRYER #I OPEN FRYER #I (SEE C-33284 FOR (SEE C-33284 FOR IRING DIAGRAM) IRING DIAGRAM) OPEN FRYER #2 (SEE C-33284 FOR WIRING DIAGRAM) OPEN FRYER #3 (SEE C-33284 FOR WIRhVG DIAGRAM1.
I I I I I I I I I I I I I I I. I I I 1 E 400 VOLT, 3 PHASE 3N’X MOTOR JWCTlON BOX 1 33558.
OE-302 iAi2Y III1 400 VOLT, 3 PHASE 3NZ, I I I I I I I I I I I I I I I I I I 33559.
I I I I I I I I I I I I I I I I I 13 12v 12ov POWER SW I TCH I I I rnulv I IrUN I KUL V’HNtL I I L3 I I --------w---m-- ------------_ -+- +------GND ,L3 ,L3 L2 L2 Ll Ll 208124OV 3PH 33726.
_-------- _-------s-w __---------w-w TIMER THERMOST FRONT CONTROL PANEL __------w-e ---s-o 1 DRAlN(;_b( I I I I I I I I I I I I I I I I I I I I I I - J 5 2 l- 2 ?2 z Y l- 208/24OV 3PH 45324.
I I I I I 47 I I I I I I 42 OPEN FRYER #1 C-45324 FOR ING DIAGRAM) OPEN FRYER #2 (SEE C-45324 FOR WIRING DIAGRAM) 39 OPEN FRYER #3 (SEE C-45324 FOR WIRING DIAGRAM) 0 OE-303 SYSTE 208/24OV 3PH 5372.
GND L3 OPEN FRYER #2 + PUMP (SEE C-45324 FOR WIRING DIAGRAM) ODEL OE-302 SYSSE 208/24OV 3PH OPEN FRYER #3 (SEE C-45324 FOR WIRING DIAGRAM) 45377.
1 i GND I I L3 L2 Ll OPEN FRYER ~rl (SEE C-45324 FOR WIRING DIAGRAM1 GND L3 L2 Ll 2: 2! III PUMP OE-300 SYST 208/24OV 3PH OPEN FRYER 792 (SEE C-45324 FOR WIRING DIAGRAM1 OPEN FRYER x3 (SEE C-45324 FOR.
OPEN FRYER #l OPEN FRYER #l (SEE C-45324 FOR (SEE C-45324 FOR WIRING DIAGRAM1 WIRING DIAGRAM1 GND L3 L2 Ll EL OE-302 SYSTE 208/24OV 3PH OPEN FRYER #2 (SEE C-45324 FOR WIRING DIAGRAM).
I I I I I I I I I I ! I I I I I I THERMOSTAT POWER ---, SWITCH ONT CONTROL PANEL ---_ ------------ I I I I I I I I I I I I I I I I I J 19 18 t GND L3 L2 I 1 Ll PUMP SWITCH__ 0 2081’24OV 3PH FRYER CONTROL CSEE ABOVE FOR WIRING DIAGRAM1 .
I I I I I I I I I I I I I I I I I I I I I I I L I I I / I THERMOSTAT FRONT CONTROL PANEL - - - ----------------- MODEL OE-300 480V 3PH I I I I I I I I I I I I I I I I I I I I I J.
GND L3 L2 Ll GND L3 L2 Ll I PUMP &SWITCH CAP/RES ASSY 3'1 OPEN FRYER #l OPEN FRYER #2 (SEE C-45373 FOR (SEE C-45373 FOR IRING DIAGRAM1 WIRING DIAGRAM1 480V 3PH GND I I L3 L2 Ll 1 5 OPEN FRYER.
_______------------------------------------------- OE-303 400 VOLT 50160 HZ 3 PHASE i 3N /L II II II II II II II II /I II II II GND :a L2 Ll GND N L3 L2 Ll PUMP MOTOR.
OE-302 400 VOLT 50160 HZ 3 PHASE 3NZ, I I I f TIMER I I I .._ , I I I I PUMP MOTOR GND N L3 L2 Ll 45376.
I I I I I I I I - CONTROL BOARD PflOE INPUT I ---_----------_---------------- I TRANSFORMER -- 1 I I I I I I I I I Ll- L2- L3- - GNL TERM I NAL n PUMP MOTOR.
r OPEN FRYER (SEE C-33601 FOR IRING DIAGRA OPEN FRYER (SEE C-33601 FOR IRING DIAGRAM) GND I I L3 L2 Ll OPEN FRYER #3 (SEE C-33601 FOR WIRING DIAGRAM1 480V 3PH.
GND I I L3 L2 Ll OPEN FRYER #1 C-33601 FOR ING DIAGRAM) I PUMP -3 T 48OV 3PH OPEN FRYER i4r2 (SEE C-33601 FOR WIRING DIAGRAM1.
MODEL 06-303 GAS FRYER 230V 50HZ 1PH.
MAIN SWITCH PUMP SWITCH ,3 I Y 21 722 15 I t- 17 14 I Y 16 16 I l-1 18 MODEL 06-302 GAS FRYER 230V SOHZ 1PH.
Henny Penny LIMITED W ARRANTY FOR HENNY PENNY APPLIANCES Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Pe.
.
Henny Penny Model OE/OG 301/302/303 SECTION 7. P AR TS INFORMA TION 7-1. INTRODUCTION This section identifies and lists the replaceable parts of the Henny Penny 3-W ell Open Fryer . 7-2. GENUINE P AR TS Use only genuine Henny Penny parts in your unit.
.
33309 33308 44784 43768 40500 30978 28979 Control Panel Assembly Complete (Gas Models) - 120V Control Panel Assembly Complete (Electric Models) - 208/24OV Control Panel Assembly Complete (Gas Models) .
. ..
Electrical Components (Electric Models) Thermal Sensor (Probe) High Temperature Limit Control Thermocouple Pot Fitting Fuse Holder Assy. (5 amp) Fuse Holder Assy.
Limit control..
Henny Penny Model OE/OG 301/302/303 Thermal Sensor and High T emperature Limit Contr ol (Gas Models) Item Part Q uantity per unit No . Number Description 30 3 3 02 3 01 7 - 3 Thermal Sensor and High T emperature Limit Control (Gas Models) √ √ √ √ √ l 16738 High T emperature Limit Control 3 2 1 √ √ √ √ √ 1 14267 High T emp.
Figure 7-4. Firebox and Flue Assembly (Gas Model).
Part Number 33166 16406 33164 33162 55328 Description Firebox and Flue Assembly (Gas Models) Firebox Front Cover Assy. Heat Shield Outer Firebox Weld Assy.
re 7-5. 1.
Outer Front Firebox Assy. (Gas Model) Outer Front Weld Assy. Insulation-Front Firebox Insulation-Top Front.
w Y.
Part Number 33348 33046 55327 16503 16502 33346 33456 55326 Description Firebox Insulation Assembly (Gas Model) Insulation-Top/Sides Insulation-Firebox Sides Insulation-Firebox sides - CE - OG-301 Insulation-Bottom Panel Insulation-Back Panel Insulation- 1 in.
T - .
7-7 la lb 1A 1B 2a 2A 2b 2B 3 4 5 er 16216 16217 16380 16381 16254 16710 16386 16384 16253 16352 16267 escri~tio Gas Control Valve (Gas Model) Valve, Control, Natural Gas, 120 Volt Valve, Control, Pro.
Gas Line and Burner Assembly (Gas Model).
Henny Penny Model OE/OG 301/302/303 Gas Line and Burner Assy . (Gas Model) Item Part Description Quantity per unit N o . Number 3 0 3 3 0 2 3 0 1 7-8 Gas Line and Burner Assy . (Gas Model) 2 FP01-093 Elbow - 1 in. NPT x 90 Female BI 1 - - 4 FP01-108 Nipple - Pipe 1"x 8" BI 1 - - 5 FP01-092 Cross T ee - 1 in.
.
el Assy. - Right Gas Line Gas Line Assy. w/Swivel (not shown).
.
Henny Penny Model OE/OG 301/302/303 Drain Valve Assembly (Gas Model) Item Part Description Quantity per unit No. Number 303 302 301 7 - 9 Drain V alve Assembly (Gas Model) 1 17260 Body Assembly , Drai.
Y.
Drain Valve Assembly (Electric Model) Nipple, Drain Extension Rod, Drain Valve Extension Cover, Valve Handle Bracket, Drain Valve Screw, Drain Valve Bracket Screw, Microswitch Nut, Microswitch Cover, .
et.
Henny Penny Model OE/OG 301/302/303 Drain Pan and Filter Screen Assembly (Gas and Electric Models) Item Part Description Quantity per unit No. Number 303 302 301 7-11 Drain Pan and Filter Screen Assy.
I I.
Seal, Mechanical, Vitoq Spacer, Pump Filter Washer, Motor Shaft Screw, Pump Shield 67583 √ √ √ √ √ √ √ √ √ √ √ recommended parts.
.-lp-- --- r + ------ t- .-- CON- rRoL ; SHFI OUD I -*-B--p et GAS & PILOT CONTROL VALVE.
7- 13 1 2 3 4 5 6 7 8 9 9 10 10 11 12 12 12 13 er ME50-02 1 18105 18107 17221 33224 18104 18105 33228 18101 54944 18102 54965 18103 33353 17902 55372 18644 Electric Conduit Assembly (Gas Model) Termin.
H -’ see.
el) Electric Conduit Assembly (Electric Model) Cover, Junction Box Connqctor, Flexible Conduit Bushing, Antishort Conduit, Flexible Connector, Flexible Conduit Bushing, Antishort Conduit, Flexible 9 1.
7- sse rie.
ode1 Cookpot and Return Line Assemblies (Gas and Electric Models) Male Connector Return Line - 301 & 303 Return Line - 302 Return Line - Upper Fitting - Return Line, Swivel 6 FPOl-004 Pipe Plug 1 1 1 7 33771 Pot & Countertop Assy. - OE-301 . 1 7 54966 Pot & Countertop Assy.
--a -- -43-m ,I WN /.
Henny Penny Model OE/OG 301/302/303 Lower Filter Plumbing Components (Gas and Electric Models) Item Part Description Quantity per unit No. Number 303 302 301 7-16 Lower Filter Plumbing Componet (Gas a.
Y el.
1 I3021 Heating Element and High Limit Assembly, (Electric Models) Element Complete, Heating, 208 Volts, Element Complete, Heating, 230 Volts, Element Complete, Heating, 220 Volts, Element Complete, H.
ode1 0 cu.
Henny Penny Model OE/OG 301/302/303 206 7-39 3-Well Front View Item Part Description Quantity per unit No. Number 303 302 301 7-18 Fry Station Front V iew 1 FP01-087 Elbow , Male - 3/8 in.
Y sse.
Henny Penny Model OE/OG 301/302/303 FIGURE QTY. & ITEM P A R T DE SCR IP TIO N P E R N O . NUMBER ASSY AUTOMA TIC RESET TIMER ASSEMBL Y √ √ √ √ √ 1 16659 BUZZER COIL ASSY , 120 V ............................................. 1 √ √ √ √ √ 1 18302 BUZZER COIL ASSY , 208-240 V .
-.
Henny Penny Model OE/OG 301/302/303 FIGURE UNITS & ITEM P AR T P ER N O . NUMBER DE S C R IP T I O N WELL CONTROL P ANEL √ √ √ √ √ 1 18301 TIMER, Automatic Reset, 208-240 V olt 60 Hz ....................... 1 √ √ √ √ √ 1 16602 TIMER, Automatic Reset, 1 15 V olt 60 Hz .
An important point after buying a device Henny Penny OG-30X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny OG-30X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny OG-30X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny OG-30X you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny OG-30X will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny OG-30X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny OG-30X.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny OG-30X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny OG-30X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
