Instruction/ maintenance manual of the product 322 Henny Penny
Go to page of 11
Model OFE/OFG-321,322,323,324 SECTION 2. INSTALLATION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Open Fryer.
Model OFE/OFG-321,322,323,324 2-3. SELECTING THE The proper location of the open fryer is very important for LOCATION the duration, speed, and convenience.
Model OFE/OFG-321,322,323,324 Ventilation must conform to local, state, and national codes. Consult your local fire department or building authorities. When installing the gas open fryer, do not attach an extension to the gas flue exha ust stack. This may impair proper operation of the burner, causing malfunctions and possible negative back draft.
Model OFE/OFG-321,322,323,324 2-6. GAS SUPPLY • The fryer and its manual shutoff valve must be disconnected (Continued) from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ PSIG (3.45 kPa) (34.
Model OFE/OFG-321,322,323,324 2-5 2005 2-6. GAS SUPPLY (Continued).
Model OFE/OFG-321,322,323,324 Prior to turning the gas supply on, be sure the gas valve knob on the gas control valve is in the OFF position. Upon initial installation, and after moving the unit, the piping and fittings should be checked for gas leaks.
Model OFE/OFG-321,322,323,324 To avoid electrical shock, do not disconnect the ground (earth) plug. This fryer must be adequately and safely grounded (earthed). Refer to local electrical codes for correct grounding (earthing) procedures or in absence of local codes, with The National Electrical Code, ANSI/NFPA No.
Model OFE/OFG-321,322,323,324 2-11. TESTING THE FRYER Each Henny Penny pressure fryer was completely checked and tested prior to shipment. However, it is good practice to check the unit for proper operation. 2-12. JOINING INSTRUCTIONS The following instructions are for joining two units together.
Model OFE/OFG-321,322,323,324 2-12. JOINING INSTRUCTIONS 12. Apply silicon around edge of unfinished side of top cover (Continued) (60590) and basket rest cover (60591). Position top cover (60590) on open fryer top cover and install basket rest cover (60591) using #10 screws and nuts (SC01-074 & 60795).
Model OFE/OFG-321,322,323,324 2-13. DIMENSIONS 211 2-10 OFX-321 OFX-322 OFX-323.
Model OFE/OFG-321,322,323,324 2-13. DIMENSIONS (Continued) 2-11 211 OFG-321 OFG-322 OFG-32X Flue & Gas Line Dimensions ( All views are from rear of fr y ers ) OFG-323.
An important point after buying a device Henny Penny 322 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny 322 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny 322 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny 322 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny 322 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny 322, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny 322.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny 322. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny 322 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
