Instruction/ maintenance manual of the product 290 Henny Penny
Go to page of 10
Model 290 1-1. INTRODUCTION This section provides troubleshooting information in the form of an easy to read table. If a problem occurs during the first operation of a new fryer , recheck the installation per the Installation Section of this manual. Before troubleshooting, always recheck the operation pro- cedures per Section 3 of this manual.
Model 290 1-3. TROUBLESHOOTING T o isolate a malfunction, proceed as follows: 1. Clearly define the problem (or symptom) and when it occurs. 2. Locate the problem in the T roubleshooting table. 3. Review all possible causes. Then, one-at-a-time work through the list of corrections until the problem is solved.
Model 290 Problem Cause Correction COOKING SECTION Product color not correct: A. T oo dark • T emperature too high • Check temperature setting in the program mode; see Programming Section in Opera.
Model 290 Problem Cause Correction COOKING SECTION (Continued) D. Spotted • Improper separation of the • Load product into racks product product properly • Breading not uniform on • Sift bread.
Model 290 Problem Cause Correction COOKING SECTION (Continued) D. Rancid taste • Shortening too old • Replace shortening, and follow recommended care and use of shortening • Infrequent filtering.
Model 290 Problem Cause Correction POWER SECTION W ith switch in • Open circuit • Check to see that unit is POWER position, plugged in the fryer is com- • Check the breaker or fuse pletely inope.
Model 290 Problem Cause Correction HEA TING OF SHOR TENING SECTION (Continued) Heating of shortening • Low or improper voltage • Use a meter and check the too slow receptacle against data plate .
Model 290 Problem Cause Correction SHOR TENING FOAMING/DRAINING SECTION Foaming or boiling • W ater in shortening • At end of a Cook Cycle, over of shortening drain shortening and clean frypot; ad.
Model 290 1-4. ERROR CODES In the event of a control system failure, the digital display shows an error message. These messages are coded: “E04”, “E05”, “E06”, “E41”. A constant tone is heard when an error code is displayed, and to silence this tone, press any of the product buttons.
Model 290 1-4. ERROR CODES (Continued) CE Only - Along with the error codes fr om page 1-1 1, CE units have the following self-diagnostic error codes: DISPLA Y CAUSE PANEL BOARD CORRECTION “E10” H.
An important point after buying a device Henny Penny 290 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny 290 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny 290 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny 290 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny 290 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny 290, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny 290.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny 290. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny 290 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
