Instruction/ maintenance manual of the product GT19wide Glancetron
Go to page of 23
T ouch Screen LCD Monitors USER’ s GUIDE Rev .A Glancetron GT19-W ide www .glancetron.com.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.
T able of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About Glancetron GT -19Wide .......................................
1 Usage Notice ! W arnin g - T o prevent the risk o f fi re or shock hazards, do not expose this product to rain or moisture. ! W arnin g - Please do not open or disassemble the product as this ma y cause e l ec tri c s h oc k.
Introduction About Glancetron GT -19Wide The Glancetron GT -19Wide is a 47cm (18.5”) fl at panel screen with an active matrix, thin- fi lm transistor (TFT) liquid crystal display (LCD). Features include: • Direct analog signal input • Active matrix TFT LCD technology • 1366 x 768 WXGA resolution • 47cm (18.
3 Package Overview LCD Display Power Cord VGA Signal Cable RS-232 Cable USB Cable ( A to B) Quick Start Guide DC Power Supply T ouch Driver CD Screw Audio-in Cable.
Installation Product Overview • Front V iew • Bottom V iew (Without Stand) POWER SWITCH DC IN VGA RS-232 USB 4.
Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included.
VESA Mount Y our Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which de fi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms.
7 Start Y our Installation Please follow these instructions so that you can hookup the cables to associated connector . 1. Lay the LCD fl at on an even surface. 2. Move the stand into position as seen in the step 2 diagram. 3. Remove the cable cover as seen in the step 3 diagram.
Remove the Deskstand Remove 4 screws and then remove hinge. 8.
Connecting the Display (Figure 10.1) T o setup this display , please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC adapter to the power connector on the monitor and the other end into an electrical outlet (10.
(Figure 10.1) 10.
User Controls Front Panel Controls Icon key Name Menu Up Down Enter Power OSD Key Menu off status Menu on status Menu appear Menu disappear / return to main item Brightness Main item select up / Adjus.
12 How to Use the OSD Menus Icon key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menus. 2. Choose the adjustment items by pressing the “Enter ” button.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right.
Appendix T roubleshooting If you are experiencing trouble with the LCD display , refer to the following. If the problem persists, please contact your local dealer or our service center .
W arning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact your local dealer or our service center for more information.
Product Dimensions 457.80 278.40 312.20 60.00 67.50 214.81 214.17 Front View Side View T op View 16.
Compatibility Modes Mode Resolution H-Frequency (KHz) V -Frequency (Hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple Mac 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA VGA 800X600 35.16 56 VESA VGA 800X600 37.88 60 VESA VGA 800X600 48.
T ouch Screen Driver Installation The Glancetron GT -19Wide is available with both RS232 and USB connections. The touch driver is located on the enclosed CD-ROM for these operating systems: Windows ® 7, VIST A 64/32 bits, XP , 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple ® Mac OS.
19 Glancetron GT -19Wide Install Instructions: If you are using a PC running Windows ® 7, VIST A, XP , 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display .
If you are using a PC running Windows ® CE, follow the instructions below: 1. Power on the computer . 2. Make sure that the RS232 or USB cable is connected to the computer . 3. Using Platform Builder , build an image fi le by following the step-by-step instructions found in the folder fi le on the CD-ROM.
An important point after buying a device Glancetron GT19wide (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Glancetron GT19wide yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Glancetron GT19wide - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Glancetron GT19wide you will learn all the available features of the product, as well as information on its operation. The information that you get Glancetron GT19wide will certainly help you make a decision on the purchase.
If you already are a holder of Glancetron GT19wide, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Glancetron GT19wide.
However, one of the most important roles played by the user manual is to help in solving problems with Glancetron GT19wide. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Glancetron GT19wide along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
