Instruction/ maintenance manual of the product BCE5232IB BTC
Go to page of 22
Dual Digital Storage Drive CD-RW 5232IB User’s Manual.
DANGER INVISIBLE LASER RADIATION WHEN O PEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN ATTENTION RADIATIO N DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYO NS.
FCC Compliance Statement This device complies with Part 15 of the FCC Ru les. Operation is subject to the following two condit ions: 1. this device ma y not cause harmful i nterference, and 2. this device must accept any interferen ce received, including interference that may cause undesired operat ion.
Table of Contents INTRODUCTION 1 S YSTEM R EQUIREMENTS 2 P ACKAGE C ONTENTS 2 INSTALLATION 3 H OST I NTERFACE C ONNECTIONS 3 H ARDWARE I NSTALLATION 4 D RIVER I NSTALLATION 6 For the CD-RW Drive 6 For.
CD-RW 5232IB 1 INTRODUCTION Thank you for the purchase of CD-RW 5232IB, a perfect and compact dual digital storage drive with the combinati on of an IDE CD-ReWritable drive and a USB-connected card reader. CD-RW 5232IB backs up all writing modes and different CD formats.
CD-RW 5232IB 2 System Requirements For IBM compatible PCs, the syst em requirements recommended are as follows: ♦ Pentium II 350MHz above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.
CD-RW 5232IB 3 INSTALLATION Host Interface Connections Most current motherboards have two IDE ports (primary and secondary) which can connect two IDE cables. Tw o IDE cables allow you to connect up to four devices, but it is reco mmended that you separate IDE ports for your hard disk and your CD-ReWritable dr ive.
CD-RW 5232IB 4 Hardware Installation 1. Turn off the power to the computer system. 2. Disconnect the power cord and all cables from the back of your computer, and then remove the cover of the computer. 3. Insert the drive into one of the vacant 5.25" drive bays and secure it with screws to your PC.
CD-RW 5232IB 5 6. Connect the USB cable at the ba ck of the drive to the USB header on the computer’s motherboard. The red wire of the cable needs to be plugged into Pin 1 on the board. This drive supports USB 2.0 and if you connect to USB 1.1 connector, only tran sfer rate of USB 1.
CD-RW 5232IB 6 Driver Installation For the CD-RW Drive For the CD-RW drive itself of CD-RW 5232IB, it is an IDE device supporting Plug & Play, and Windows 98SE/ME/2000/XP can automatically detect the drive and load the appropriate driver.
CD-RW 5232IB 7.
CD-RW 5232IB 8 Windows ME/XP Since Windows ME and XP already have USB Mass Storage support, the card reader can be detected and wo rk fine without installing driver. However, we recommend that you in stall the provided driver to have more explicit operation status of the card reader, as described below.
CD-RW 5232IB 9 Software Installation The bundled mastering software gives you the complete solution for making audio/data CDs. With the user-f riendly interface, it guides you through the creation and backup of f iles/photos/video/music from your computer to a recordable compact disc.
CD-RW 5232IB 10 CONNECTION & OPERATION Front Panel 1. A-Type USB Extension Port This USB port is Plug-and-Play R eady. Just plug your USB device and the computer will detect automatically. 2. Close/Eject Button This button opens and closes the disc tray.
CD-RW 5232IB 11 5. Emergency Eject Hole When the Close/Eject button doesn’t work properly and the disc tray can’t be opened, you can insert a paper clip or a small rod into this hole for manual ejection. Please make sure to power off the system before you do that.
CD-RW 5232IB 12 Rear View 23 4 5 6 1. Digital Audio Output Connector If your sound card has a digital audio IEC958 format connector, you can connect it to this digital audio output connector with a 2-pin audio cable. 2. Analog Audio Output Connector This connector allows you to connec t the drive to your sound card with a 4-pin audio cable.
CD-RW 5232IB 13 6. USB Cable Connect the USB cable to the U SB connector on the motherboard. The red wire of the cable needs to be plugged into Pin 1 on the board.
CD-RW 5232IB 14 TECHNICAL DATA Interface CD-RW Drive: EIDE Card Reader: USB 2.0 Form factor 5.25" Half Height Writing speed CD-R: 8X/16X/24X/32X /40X/48X/52X CD-RW: 4X/10X/12X/16X /20X/24X/32X Wr.
CD-RW 5232IB 15 Access time 90ms at ⅓ stroke(52X CD-ROM) 180ms at full stroke(52X CD-ROM) 99ms at ⅓ stroke (32X CD-RW) 200ms at full stroke (32X CD-RW) Disc loading Tray (motorised), Dust Sealed Audio output level Line out = 0.
CD-RW 5232IB 16 Environment Temperature Operating 5°C to 45°C Non-operating -20°C to 45°C Humidity Operating 8% ~ 80%RH Non-operating 5% ~ 95%RH.
.
3100552210 Version 1.0 Jan. 2004.
An important point after buying a device BTC BCE5232IB (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought BTC BCE5232IB yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data BTC BCE5232IB - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, BTC BCE5232IB you will learn all the available features of the product, as well as information on its operation. The information that you get BTC BCE5232IB will certainly help you make a decision on the purchase.
If you already are a holder of BTC BCE5232IB, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime BTC BCE5232IB.
However, one of the most important roles played by the user manual is to help in solving problems with BTC BCE5232IB. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device BTC BCE5232IB along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
