Instruction/ maintenance manual of the product BCE 4816IM BTC
Go to page of 20
CD-WRITER 4816IM CD-ReWritable Drive User’s Manual.
CLASS 1 LA SER PRODUCT APPA REIL A LA SER DE CLASSE 1 LASER KLA SSE 1 LUOKAN 1 LA SERLAITE PRODUIT LASER CATEGORIE 1 DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN ATTENTION RADIATIO N DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.
FCC Compliance Statement This device complies with Part 15 of the FCC Ru les. Operation is subject to the following two condit ions: 1. this device ma y not cause harmful interference, and 2. this device must accept any interferen ce received, including interference that may cause undesired operat ion.
Table of Contents INTRODUCTION 1 S YSTEM R EQUIREMENTS 1 P ACKAGE C ONTENTS 2 INSTALLATION 3 H OST I NTERFACE C ONNECTIONS 3 H ARDWARE I NSTALLATION 4 D RIVER I NSTALLATION 6 Windows Environment 6 S O.
CD-WRITER 4816IM 1 INTRODUCTION CD-WRITER 4816IM is a half-height CD-ReWritable drive of standard IDE interface. It supports maximu m 48x speed writing ability on CD-R discs, 16x speed on CD-RW discs and 48x speed reading performance.
CD-WRITER 4816IM ♦ Pentium II 300MHz above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.
CD-WRITER 4816IM INSTALLATION Host Interface Connections Most current mainboard models have two IDE ports (primary and secondary) which can connect two IDE cables. Two IDE cables allow you to connect up to four dev ices, but it is recommended that you separate IDE ports for your hard drive and your CD-ReWritable drive.
CD-WRITER 4816IM 4 You may consider one of the two ways recommended below to connect your drive. ♦ To get the most stable performance for the CD-RW drive to write: Primary IDE Master: Hard Disk Prim.
CD-WRITER 4816IM The red-edge of the IDE Cable must be connected to Pin 1 on the CD- ReWritable drive. 5. If you have a sound card that can be connected to this CD- ReWritable drive, you can connect the drive (as Audio-out) and the sound card (as Audio-in) with a 4- pin audio cable.
CD-WRITER 4816IM 6 Driver Installation Windows Environment CD-WRITER 4816IM is a PnP device, and Windows 95/98/ME and Windows NT/2000/XP can automatically detect the drive and load the appropriate driver. If Windows c annot detect the drive, you can operate manually: 1.
CD-WRITER 4816IM CONNECTION & OPERATION Front Panel BUSY 1. Headphone Plug By plugging in the headphone jack here, you can listen to an audio CD (CD-DA disc) directly playing from the CD-ReWritable drive. 2. Headphone Volume Control This knob adjusts the audio output level.
CD-WRITER 4816IM this hole for manual ejection. Please make sure to power off the system before you do that. 6. Play/Skip button Press this butt on to play tracks or skip to next track during the playing state. 7. Close/Eject button This button opens and closes the disc tray.
CD-WRITER 4816IM 9 3. Device Configuration Jumper Set the jumper to Master, Slave or Cable Select according to your system configuration. 4. IDE Interface Connector Plug one end of the 40-pin IDE cable here to join the 40-pin IDE connector on the motherboard.
CD-WRITER 4816IM 10 TECHNICAL DATA Performance Transfer rate Read: 7200kb/s (up to 48X) Write: CD-R 7200kb/s(up to 48X) CD-RW 2400kb/s(up to 16X) Access time 85ms at ⅓ stroke (48X CD-ROM) 180ms at f.
CD-WRITER 4816IM 11 Audio output level Line out = 0.6 ± 10%Vrms Headphone out = 0.6± 10%Vrms Power 5 VDC & 12VDC Dimensions Height 41.8 ± 0.2 mm Width 148.
CD-WRITER 4816IM 12 Humidity Operating humidity 8% ~ 80%RH Non-operating humidity 5% ~ 95%RH.
CD-WRITER 4816IM 13 TROUBLESHOOTING To help you get more familiar with CD-WRITER 4816IM, the following FAQ lists some common problems you might encounter. Please read it for reference before you request RM A support from your dealer. Q1. CD-WRITER 4816IM cannot be recognized.
CD-WRITER 4816IM 14 Please check if the power cord is connected securely. Q6. The tray cannot be ejected. There are two possible reasons: (1) Need to be ejected by the application. Some of the burning or playing applic ation will lock the drive. You have to eject by application and close it so as to restore the use of panel buttons.
CD-WRITER 4816IM 15 (4) Increase main memory capacity. (5) Select other burning software. (6) De-fragment the hard disk. (7) Keep the source & destination discs clean. (no scratches, fingerprints or contamination.) (8) Copy data as image file to hard drive to avoid buffer underrun.
3100550470 Version 1.0 June 2002.
An important point after buying a device BTC BCE 4816IM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought BTC BCE 4816IM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data BTC BCE 4816IM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, BTC BCE 4816IM you will learn all the available features of the product, as well as information on its operation. The information that you get BTC BCE 4816IM will certainly help you make a decision on the purchase.
If you already are a holder of BTC BCE 4816IM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime BTC BCE 4816IM.
However, one of the most important roles played by the user manual is to help in solving problems with BTC BCE 4816IM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device BTC BCE 4816IM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
