

A. Quick Set-Up Method
C. Auto-Search Method
STEP1 Press the [TV] button and the [OK/SEL]
Operating Instructions
button simultaneously for 3 seconds.The [AUX] Component LED will light for 30 seconds.
button simultaneously for 3 seconds. The [TV] Component LED will light for 30 seconds.
This remote control is designed to operate all Motorola and Scientific Atlanta digital set top boxes (including HD and DVR), plus the majority of TVs, VCRs, DVDs and AUDIO equipment on the market as shown below.
to program your TV, turn the TV on.
program (TV, VCR, DVD or AUX).
STEP2 Press the [VOL -] button.
STEP2 Point the remote at the TV and press
STEP3 Press the [COMPONENT] button you want
and hold the TV key for 3 seconds. While Holding the TV key, the TV LED will light off and on again. Begin to press the number keys, one at a time, starting with 1, then 2, 3…0 until the TV turns off.
DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds indicating the unit is ready to be programmed.
to setup. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand.
STEP3 Press the [TV] button again.
The Component LED will blink twice to confirm the programming.
CABLE: Cable Converters TV: Televisions DVD: DVDs, TV/DVDs, VCRs and TV/VCRs AUX: Audio Receivers and DVRs, etc.
*Note : If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off.
UR4U-MDVR-CHD2
If you wish to restore the CABLE channel control in
STEP3 Release the TV key to save the code.
Component and press the [CH] or [CH] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH] or [CH] button as soon as the Component turns Off.
The TV LED will blink twice to confirm the code is stored.
in STEP3 .

Repeat these steps for your DVD, Aux, etc.
Before you program or operate this remote control, you must first install two new AA Alkaline batteries.
Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
You can program the volume controls (Volume Up, Volume Down and Mute) from one Component to operate in another Component mode. Default volume control settings on the remote control are as follows:
STEP1 Remove the battery compartment cover
program (TV, VCR, DVD or AUX) .
Programming Method - Section A). If any of the functions do not work as they should, repeat from STEP 3 using [CH] or [CH] buttons to find the correct code.
on the back of your remote control.
code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 4
DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds indicating the unit is ready to be programmed.
install the batteries as shown in the illustration below.
STEP5 Save the code. (Same as for 3-Digit Code
STEP3 Replace the battery compartment cover.
Programming Method - Section A).
If you wish to operate the CBL volume control in CBL mode, use the following steps.
Component.
Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method.
F. Programming the System On/Off Button
STEP1 Press the [CBL] button and the [OK/SEL]
Component and enter the 3-digit code number assigned to your brand.
button simultaneously for 3 seconds. The [CBL] Component LED will light for 30 seconds.
This allows you to program the System On/Off button so it can send up to four power On/Off commands with one button press.
*Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off.
Setup Code Number
STEP2 Press the [VOL +] button.
STEP1 Press the [CBL] button.
STEP3 Press the [CBL] button.
If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference.
The Component LED will blink twice to confirm the programming.
[OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will light for 30 seconds.
To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps but press [TV]
number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand.
STEP3 Press the first [COMPONENT] button you
AUX) you want to verify and the [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds.
want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button.
in STEP3 .
number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off.
See on-screen Guide Menu.
Operations 3
* Quick Set-Up Method * The Pre-Programm rogrammed 3-Digit Code Method * The Auto-Search Method The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using one-digit codes for up to 10 major brands for each component. The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto- Search Method scans through all the codes in the remote control, one at a time.
J. Low Battery Warning When the batteries are low and need to be replaced with fresh batteries, the Component LED lights will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.
commands you stored. The [CBL] button will blink twice to confirm the commands have been saved.
DEFAULT STATUS: Component Default: CABLE Channel Default: CABLE channel +/- and numbers operate through the CABLE box. You have the option of controlling channel +/- and numbers through the TV, VCR or DVD. Refer to section G for programming steps.
digit code, save it by pressing the same [COMPONENT] button one more time. The Component LED light will blink twice to confirm that the code was successfully stored.
*Note : 10 blinks represents the number zero.
G. Programming Channel Control
K. Memory Lock System This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
three blinks, indicates code number 183.
You can program the channel controls (Channel Up, Channel Down, Last and Numbers) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows:
Now, program the rest of your Components by repeating STEPS 1-5.
Volume Default: CABLE volume +/- and mute operate through the TV. You have the option of controlling volume through the Cable box, VCR or DVD. Refer to section H for programming steps.
IMPORTANT SETUP NOTES: This pertains to all programming steps. When you are in setup mode in each component, a component LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to start over. When programming a combo unit, program as a VCR or DVD first.
*Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the Auto-Search Method as explained in Section B.
th Component such as a second TV, VCR, DVD or Audio Component.
Universal Remote Control, Inc.
STEP1 Turn on the 4
th Component you want to program (TV, VCR, DVD or Audio).
If you wish to operate the TV channel control in TV mode, use the following steps.
th

EMERSON 143 MAGNAVOX 143 PANASONIC 144 SUPERSCAN 143 SYLVANIA 143 TOSHIBA 164
Manufacturer/Brand Set-Up Code Number DVD-DVD/VCR Combos
Manufacturer/Brand Set-Up Code Number AUX-DVR(TIVO)
GO VIDEO 137 PANASONIC 150 PHILIPS 066 (VCR Functions for VCR 567) RCA 027 (VCR Functions for VCR 644) SAMSUNG 137 159 SANSUI 154 SONY 145 TOSHIBA 141 ZENITH 091 (VCR Functions for VCR 601)
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.