
Introduction 1

*Tip: The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [MUTE] button, the equipment should turn on or turn off.
D. Programming a second TV
STEP3 Press the [DEVICE] button
G. Programming For
one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.
to VCR Mode.
you wish to store in the [SYSTEM ON/OFF] button and repeat this until you stored all the power commands into the [SYSTEM ON/OFF] button.
Advanced Function. In the CABLE mode, the [* ] button can be programmed to act as a macro or favorite channel button to send out up to 10 commands with one button press.
The remote control is designed to operate the DTV series set top boxes and the majority of TV, VCR/DVD and AUDIO equipment on the market.
program. STEP2 Press the [VCR] button to be
programmed and the [SELECT] button simultaneously for 3 seconds. The [VCR] device LED will turn on.
Replacing Batteries 2
*Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
*Tip: You can verify that you selected the correct code by pressing the [MUTE] button. The TV should either turn on or turn off.
select the CABLE mode.
the power commands you stored. The [CBL] device LED will blink twice to confirm the saving.
Before you program or operate the remote control, you must install two new AA alkaline batteries.
*Tip: The device LED will light on for 20 seconds. The next step must be entered while the LED is on.
[SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds.
STEP4 Press the same [DEVICE]


number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
button to store the code. The Device LED will blink twice to confirm that the code has been stored.
F. Program the Volume
STEP3 Press up to 10 buttons you
on the back of your remote control. STEP2 Check battery polarity carefully,
access the TV code table. STEP4 Point the remote control
Controls. By following the steps below, you can program the volume controls (Volume UP, Volume Down and MUTE) to your TV, VCR and Audio. The default volume control settings on the remote control is TV volume control. If you wish you can control the volume via your cable box or audio equipment. Use the following steps to change the volume control settings:
wish to store. The [CBL] button LED will blink once for each command entered.
and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover.
toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. *Tip: You can verify that you selected the correct code by pressing the [MUTE] button. The equipment should either turn on or turn off.
*Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list. Make sure that the VCR/VOD button is in the VCR position when using your VCR.
the functions that are selected. The [CBL] device LED will blink twice to confirm the storage of functions.
Code Number That was Stored in the Device.
H. Low Battery Warning. When the battery is low (2.0V-2.3V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment.
VCR or AUD) you wish to verify and the [SELECT] button simultaneously for 3 second. The device LED will turn on.
number by pressing the [VCR] button once again. The [VCR] device LED will blink twice to confirm that the code has been stored.
B. Auto Search Method.
the [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on.
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
*Tip: The device LED will light on for 20 seconds. The next step must be entered while the LED is on.
I. Memory Lock System. This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
A. Programming For Your Devices.
*Tip: The device LED will light on for 20 seconds. The next step must be entered while the LED is on.
STEP2 Press the [INFO] button.
System On/Off Button.
Default State : Device Default: DTV Cable box. Volume Default: TV volume and mute through the TV, with the option of controlling volume and mute through the Cable box or Audio. Refer to Section F for programming the volume and mute through your Cable box or Audio.
The remote control can be programmed by pressing in a three digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual.
The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second pause of the LED being turned off.
This button is pre-programmed to turn on all devices with one button press, however you can also program to turn on one or two devices by following these steps:
STEP2 Press the [ VOL + ] button.
wish to operate.
![Universal Remote Control Universal Remote Control (4 Function DTV Remote Control) — STEP3 Press the [ CBL ], [ AUD ] diagram (page 1)](/cdn/reader/ba/ba1c07326b10b7c25105028a6e7f3852a9ce247488f4d4a6d04f7800f5c8c9e9/images/fig-1-4.webp)
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUDIO).
(whichever applicable) button. The [CBL] device LED will blink twice to confirm the programming.
J. Write your device Set-up codes.
STEP2 Press the [DEVICE] button (TV , VCR or AUD) to be programmed and the
VCR or AUD) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on.
STEP1 Press the [CBL] button.
[SELECT] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed.
Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138.
System On/Off button: This button is designed to send out power commands for two, three or all four devices with one button press. Please refer to section E for details.
*Tip: The device LED will light on for 20 seconds. The next step must be entered while the LED is on.
button and the [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds.
To return to original state: If you wish to restore the TV volume control in CABLE mode, repeat the above steps by pressing [ TV ] button in
Universal Remote Control, Inc.
*Tip: The device LED will light on for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit
code number assigned to your brand from the code tables.

Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.