EN
Universal Remote Control logo
Official user manual

Universal Remote Control Remote Control (M-855)

63 pages·930 KB·Remote Control·PDF·ENDEFRITNLJA
Universal Remote Control Remote Control (M-855)
Table of Contents 80 sections M-855 Industrial Motherboard · User’s Manual · Trademarks · Getting Service from ADLINK · … ShowHide
M-855 Industrial Motherboardp.1User’s Manualp.1Trademarksp.3Getting Service from ADLINKp.4Introductionp.71.1 Unpacking Checklistp.81.2 Featuresp.9M-855 Series Overviewp.101.3 System Block Diagramp.11DATA CTRL ADDRp.11LVDSp.11DDR266/333 X2 LCD / CRTp.11ATA100p.11ICH4 421 BGAp.11USB2.0p.11PCI BUSp.11PCI SLOTSp.11S-ATA S3112p.11FWHp.11FINTEK F81216Dp.11COM1/2 COM3/4p.111.4 Specificationsp.122.1 System Installationp.15CPU Installationp.15OPENp.15OPEN CLOSEDp.15CLOSEDp.15Memory Module Installationp.162.2 Board Layoutp.192.3 Jumper Settingsp.20JP1/JP2 Functionp.20Function JP3p.21Function JP4p.21NMI 1-2p.21Function JP5p.21Function JP6p.222.4 Connector Descriptionsp.22CRT VGA Port Connector (D-SUB 15-pins Female): CN1p.24Parallel Port Connector (D-Sub 25-pins Male): CN3p.25Audio Port Connector (Audio Phone–Jack): CN5 (Optional)p.26Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack): CN7p.27CD_IN Connector: CN9p.28Pin # Assignmentp.282 CD_GNDp.283 CD_GNDp.28Pin # Assignment Pin # Assignmentp.281 DCD 2 RXDp.283 TXD 4 DTRp.287 RTS 8 CTSp.2811 TXD+ 12 TXD-p.28COM4 RS-232/422/485 Serial Port Connectors (14-pins Pin-Header): CN14p.29CPU Fan Power Connector: CN15p.3023 YBM1 24 YBM2p.3125 YBP1 26 YBP2p.3129 CLKBM 30 YBM3p.3131 CLKBP 32 YBP3p.3133 NC 34 +12Vp.3135 NC 36 +12Vp.3137 NC 38 PVCCp.31USB 4/5 Connector (9-pins Pin-Header): CN19p.32Pin # Assignment Pin # Assignment SPEAKER PWR LEDp.32Secondary IDE Connector (40-pins 2.54mm Pitch Pin-Header with Housing): CN21p.33ATX Power Connector: CN22p.34LINE OUT Connector: CN25p.361 LOUT_Lp.362 AU_GNDp.363 VCC_5Vp.361 LINK_LED 2 VCC_3Vp.36S-ATA1 Connector (9-pins): SATA1p.37Type II CompactFlash™ Connector: CF IIp.38CFp.38Award BIOS Setupp.393.1 BIOS Instructionsp.393.2 Main Menup.393.5 Advanced BIOS Featuresp.45Phoenix - AwardBIOS CMOS Setup Utilityp.45F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Onboard IDE Device:p.51Onboard Devicep.52SuperIO Devicep.533.9 PnP/PCI Configurationsp.58
Page 1 of the Universal Remote Control Remote Control (M-855) user manual — User’s Manual
Page 1 · click to enlarge
Page 1

M-855 Industrial Motherboard

User’s Manual

Recycled Paper 60070024IHA00

Page 2 of the Universal Remote Control Remote Control (M-855) user manual — M-855 Industrial Motherboard
Page 2 · click to enlarge
Page 2
Page 2 of the Universal Remote Control Remote Control (M-855) user manual — M-855 Industrial Motherboard
Page 3 of the Universal Remote Control Remote Control (M-855) user manual — Trademarks
Page 3 · click to enlarge
Page 3

© Copyright 2004 ADLINK Technology Inc.

All Rights Reserved.

Manual Rev. 1.00August 16, 2004

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

NuDAQ®, NuIPC®, NuDAM®, NuPRO® are registered trademarks of ADLINK Technology Inc. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Page 4 of the Universal Remote Control Remote Control (M-855) user manual — Getting Service from ADLINK
Page 4 · click to enlarge
Page 4

Getting Service from ADLINK

Customer Satisfaction is top priority for ADLINK Technology Inc. If you need any help or service, please contact us.

Universal Remote Control Remote Control (M-855) — Getting Service from ADLINK diagram (page 4)
Fig. 1 · Getting Service from ADLINK
ADLINK TECHNOLOGY INC. Web Sitehttp://www.adlinktech.com Sales & [email protected] TEL+886-2-82265877FAX+886-2-82265717 Address9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan

Please email or FAX your detailed information for prompt, satisfactory, and consistent service.

Universal Remote Control Remote Control (M-855) — Getting Service from ADLINK diagram (page 4)
Fig. 2 · Getting Service from ADLINK
OSComputer Brand: M/B: CPU: Chipset: BIOS: Video Card: NIC: Other:
Page 5 of the Universal Remote Control Remote Control (M-855) user manual — Getting Service from ADLINK
Page 5 · click to enlarge
Page 5
Page 5 of the Universal Remote Control Remote Control (M-855) user manual — Getting Service from ADLINK
Page 6 of the Universal Remote Control Remote Control (M-855) user manual — Getting Service from ADLINK
Page 6 · click to enlarge
Page 6
Page 6 of the Universal Remote Control Remote Control (M-855) user manual — Getting Service from ADLINK
Page 7 of the Universal Remote Control Remote Control (M-855) user manual — Introduction
Page 7 · click to enlarge
Page 7

Introduction

The M-855 series combines the high performance and exceptional value of the Intel® 855GME chipset with a full-featured, next generation, industrial board. The Intel® 855GME advanced chipset supports socket 478-pins Intel® Pentium® M processors ranging from 1.30GHz to 1.80GHz, and up to 2GB DDR SDRAM memory on its 400/533MHz FSB. It includes an integrated LVDS and VGA, an onboard Intel® 82541 Gigabit Ethernet controller (supporting 10/100/1000 Base-TX Ethernet), audio line-out, four COM ports, two internal USB2.0 ports, 2 SATA ports, and a CompactFlash™ type II connector. M-855 uses include ATM, CTI, KIOSK, POS, and other high-end applications. The 82801DB I/O Controller Hub (ICH4) employs the Intel® Accelerated Hub Architecture to make a direct connection from the graphics chip and memory to the integrated Ethernet controller, IDE controllers (ATA/33, ATA/66, or ATA/100), and six USB ports. The M-855 industrial board supports Windows® 98/NT/2000/XP and Linux® operation system.

Introduction • 1

Page 8 of the Universal Remote Control Remote Control (M-855) user manual — 1.1 Unpacking Checklist
Page 8 · click to enlarge
Page 8

1.1 Unpacking Checklist

1. Take out the M-855 series unit from the carton box, check if the unit is properly secure in its plastic bag. 2. Check the contents of the carton box: ¡ Industrial Board ¡ Installation Guide ¡ ATA-66/100 HDD ribbon cable ¡ Floppy ribbon cable ¡ S-ATA & Power cable (1 Set) ¡ Driver CD ¡ COM3 ribbon cable (1 Set) ¡ External K/B & M/S cable (for RS-232/422/485) (6-pin to 6-pin)
Universal Remote Control Remote Control (M-855) — 1.1 Unpacking Checklist diagram (page 8)
Fig. 3 · 1.1 Unpacking Checklist
Universal Remote Control Remote Control (M-855) — 1.1 Unpacking Checklist diagram (page 8)
Fig. 4 · 1.1 Unpacking Checklist
Universal Remote Control Remote Control (M-855) — 1.1 Unpacking Checklist diagram (page 8)
Fig. 5 · 1.1 Unpacking Checklist

2 • Introduction

Page 9 of the Universal Remote Control Remote Control (M-855) user manual — 1.2 Features
Page 9 · click to enlarge
Page 9

¡ Low profile heat sink with fan ¡ I/O Shield

Universal Remote Control Remote Control (M-855) — 1.2 Features diagram (page 9)
Fig. 6 · 1.2 Features
Universal Remote Control Remote Control (M-855) — 1.2 Features diagram (page 9)
Fig. 7 · 1.2 Features

!

shock. Never remove any of the socketed parts except at a static-free workstation. Use the anti-static bag shipped with the product to handle the board. Wear a wrist strap grounded through one of the system's ESD Ground jacks while servicing system components.

1.2 Features

  • Intel ® Pentium ® M / Celeron ® M processor
  • Intel ® 855GME + ICH4 AGPset
  • Support 2GB DDR266/333 SDRAM (max.) memory
  • Front Side Bus Frequency: 400/533MHz
  • Chipset integrated graphic & LVDS function
  • Single 10/100/1000 Mbps Gigabit Ethernet using Intel ® 82541 chip
  • Software programmable watchdog timer
  • Hardware Monitoring
  • AC97 Audio Lin-out pin-header Hardware Monitoring Hardware monitoring allows the user to monitor various aspects of system operations and status (including the CPU temperature, voltage, and fan RPM). I/O Shield Connector The SBC is equipped with an I/O bracket. Please use the appropriate I/O shield.

Introduction • 3

Page 10 of the Universal Remote Control Remote Control (M-855) user manual — M-855 Series Overview
Page 10 · click to enlarge
Page 10
Universal Remote Control Remote Control (M-855) — M-855 Series Overview diagram (page 10)
Fig. 8 · M-855 Series Overview
Figure 1I/O back panel layout

M-855 Series Overview

Universal Remote Control Remote Control (M-855) — M-855 Series Overview diagram (page 10)
Fig. 9 · M-855 Series Overview
FunctionM-855 ¡ ChipsetIntel® 855GME ¡ LVDS€ ¡ VGA€ ¡ Gigabit Ethernet€ ¡ 40-pins EIDE interface2 ¡ Type II CF socket1 ¡ Parallel ports1 ¡ Serial ports4 ¡ PCI slots3 ¡ USB 2.0 ports (two for USB cable)6 ¡ Audio Line-out pin-header1 ¡ Fan connector2

4 • Introduction

Page 11 of the Universal Remote Control Remote Control (M-855) user manual — ICH4 421 BGA
Page 11 · click to enlarge
Page 11

1.3 System Block Diagram

for Intel Pentium M

DATA CTRL ADDR

LVDS

DDR266/333 X2 LCD / CRT

GMCH (855GME) 732 Micro FCBGA

ATA100

Intel 82541 10/100/1000 Base-TX

ICH4 421 BGA

USB2.0

PCI BUS

PCI SLOTS

S-ATA S3112

FWH

FINTEK F81216D

COM1/2 COM3/4

Figure 2System Block Diagram
Show 19 more labels / short text on this page
Socket 478-pins · Clock VRM · 400/533 MHz FSB · or VGA · Device · IDE Primary · AC97 Audio Codec · IDE Secondary · CF Socket · USB Port 0/1 · USB Port 2/3 · USB Port 4/5 · Super I/O W83627HF · SATA Port 1/2 · Keyboard · Mouse · Floppy · LPT Port · Introduction • 5
Page 12 of the Universal Remote Control Remote Control (M-855) user manual — 1.4 Specifications
Page 12 · click to enlarge
Page 12

1.4 Specifications

¡ Processor:

- Intel® Pentium® M processor with socket 478-pins package - Processor operating at 1.3GHz and up to 1.8GHz - System bus frequency at 400 / 533 MHz FSB Make sure you use the correct CPU (Pentium® M processor). Using a standard Pentium® 4 CPU may crash the system. ¡ Chipset: - Intel® 855GME + ICH4 AGPset ¡ DRAM Module:

- 2 x 184-pin DIMM socket - DDR 266/333 memory - Support DDR SDRAM up to 2GB (max.) ¡ LVDS & VGA:

- Intel® 855GME Chipset integrated LVDS & Graphic controller - Onboard 15-pin VGA connector ¡ Gigabit Ethernet:

- Intel® 82541 Ethernet controller - 10/100/1000 Base-TX Ethernet - Onboard RJ-45 Ethernet connector ¡ External Connector:

- 1 x type II CompactFlash™ connector (using a CF card will occupy the IDE2 master) - 1 x 6-pin KB/MS extender ¡ Expansion Slot:

- Three PCI slots ¡ Onboard I/O: - On-Chip I/O integrated with Keyboard, Mouse, Parallel and Serial, and Power-ON controller ¡ Onboard PCI / IDE: - Intel® ICH4 south bridge controller - PCI rev2.2 Compliant - ACPI Compliant Power Management - PCI Bus IDE Port with PIO / Ultra DMA-100 x 2 (up to 4 devices)

6 • Introduction

Page 13 of the Universal Remote Control Remote Control (M-855) user manual — 1.4 Specifications
Page 13 · click to enlarge
Page 13

¡ Rear I/O Connectors:

- PS/2 Mouse and PS/2 style Keyboard - D-Sub 25-pins Printer port connector D-Sub 9-pins COM1 Serial port connector for RS-232 D-Sub 15-pins VGA connector - 2 x USB2.0 connectors - RJ-45 Ethernet and 2 x USB2.0 connectors - Audio for Line-In, Line-Out, MIC phone jack (Optional) ¡ Internal I/O Connectors (pin-header):

- 3 x Serial ports, COM2 for RS-232 and COM3 / 4 for RS-232/422/485

(Serial cable with bracket) - 2 x USB2.0 connectors (USB cable with bracket) - 2 x S-ATA connectors - Audio Line-Out pin-header ¡ BIOS: - Award Plug & Play BIOS ¡ Form Factor: - 9.6” x 9.6” (244 x 244mm) Micro ATX Size ¡ Weight: - 1.44lb (650g) --- M-855 series

Introduction • 7

Page 14 of the Universal Remote Control Remote Control (M-855) user manual — 1.4 Specifications
Page 14 · click to enlarge
Page 14
Page 14 of the Universal Remote Control Remote Control (M-855) user manual — 1.4 Specifications
Page 15 of the Universal Remote Control Remote Control (M-855) user manual — OPEN
Page 15 · click to enlarge
Page 15

2.1 System Installation

CPU Installation

Carefully follow the steps below to install the CPU: 1. Check and confirm that the jumpers are correctly set for the CPU you are going to install (figure 3). 2. Take the screwdriver and releasing screw-nut of the Socket 478. 3. Rotate mark of screw-nut to face the “OPEN”. 4. Align the pins of the CPU against the pinholes of the Socket 478. Be sure to pay attention to the orientation of the CPU.

Universal Remote Control Remote Control (M-855) — CPU Installation diagram (page 15)
Fig. 10 · CPU Installation

OPEN

OPEN CLOSED

CLOSED

Figure 3: CPU Socket 5. Push down the CPU into the Socket 478. 6. Rotate mark of screw-nut to face the “CLOSED”. 7. Place the CPU cooling fan atop the CPU surface.

Screw Nut

Page 16 of the Universal Remote Control Remote Control (M-855) user manual — Memory Module Installation
Page 16 · click to enlarge
Page 16
8. Push down the opposite side of the ZIF clip and hook it. 9. Connect the cooling fan cable to the socket as shown below. Be careful not to place the cable on the CPU cooling fan.

Removing a CPU: 1. Before removing the CPU, turn off the power and wait for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cools down. 2. Rotate mark of screw-nut to face the “OPEN”. 3. To remove the CPU.

burns.

Heat Sink & Retention Module Installation It is highly recommended that only the M-855 Heat sink and fan (Figure 4), designed for use in the chassis be used. The use of other heat sinks, including those boxed with CPUs, may damage the M-855. Make sure that good contact is made between the processors and the heat sinks. Insufficient contact, incorrect types of heat sinks, fans, or thermal compound used or improper amount of thermal compound applied on the CPU die can cause the processors to overheat, which may crash the system. The Retention Module is used to hold up the weight of the Heat sink and fan.

Universal Remote Control Remote Control (M-855) — Memory Module Installation diagram (page 16)
Fig. 11 · Memory Module Installation
Figure 4Heat Sink & Retention Module Installation

Memory Module Installation

Page 17 of the Universal Remote Control Remote Control (M-855) user manual — Memory Module Installation
Page 17 · click to enlarge
Page 17

Figure 5 display the notch marks and what they should look like on your DIMM memory module. DIMMs have184 pins and two notches that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90-degree angle and pressing straight down (figure 6) until it fits tightly into the DIMM socket.

Universal Remote Control Remote Control (M-855) — Memory Module Installation diagram (page 17)
Fig. 12 · Memory Module Installation
Figure 5DIMM Memory and 184-pins Socket
Universal Remote Control Remote Control (M-855) — Memory Module Installation diagram (page 17)
Fig. 13 · Memory Module Installation

Figure 6: Memory Installation Carefully follow the steps below in order to install the DIMMs: 1. To avoid generating static electricity and damaging the DIMM, ground yourself by touching a grounded metal surface or using a ground scrap before you touch the DIMM. 2. Do not touch the connector of the DIMM. Dirt residue may cause a malfunction. 3. Hold the DIMM with its notch to the front side of the M-855 and insert it completely into the socket. A DIMM should be inserted into the inner socket first. Guiding the hole at each end of the DIMM over the retaining post at each end of the DIMM socket. 4. If you install two DIMMs, install the second DIMM using the same procedure as above. 5. If DIMM does not go in smoothly, do not force it. Pull it all the way out and try again. 6. Make sure the DIMM is properly installed and locked by the tabs on both sides of the socket. Removing a DIMM:

Page 18 of the Universal Remote Control Remote Control (M-855) user manual — Memory Module Installation
Page 18 · click to enlarge
Page 18

To remove the DIMM, use your fingers or a small screwdriver to carefully push away the plastic tabs that secure the DIMM at each end. Lift it out of the socket. Make sure you store the DIMM in an anti-static bag. Only use the same size and manufacturer of memory modules. Setting Jumpers and DIP Switches There are jumpers and DIP-switches on the M/B of the M-855 Series. The jumpers can be set for various operations.

Universal Remote Control Remote Control (M-855) — Memory Module Installation diagram (page 18)
Fig. 14 · Memory Module Installation

Figure 7: Jumper Connector For any three-pins jumpers (Figure 7), the jumper setting is 1-2 when the jumper connects pins 1 and 2. The setting is 2-3 when pins 2 and 3 are connected. The numbers “1“ and a “3“ are printed on the circuit board to identify these pins. And also, there is a second way of indication – one of the lines surrounding jumpers is thick, which indicates pin number 1. To move a jumper from one position to another, use needle-nose pliers or tweezers to pull the pin cap off the pins and move it to the desired position.

Page 19 of the Universal Remote Control Remote Control (M-855) user manual — 2.2 Board Layout
Page 19 · click to enlarge
Page 19

2.2 Board Layout

Universal Remote Control Remote Control (M-855) — 2.2 Board Layout diagram (page 19)
Fig. 15 · 2.2 Board Layout
Figure 8Jumper and Connector Locations
Page 20 of the Universal Remote Control Remote Control (M-855) user manual — JP1/JP2 Function
Page 20 · click to enlarge
Page 20

2.3 Jumper Settings

Jumper Location Description: Use the information in the following table to change the jumpers and the DIP switches.

Jumpers Functions JP1 COM3 Port Setting Select JP2 COM4 Port Setting Select JP3 CPU Type Setting Select JP4 Watchdog Timer Setting Select JP5 Clear CMOS Setting Select JP6 Power Management Setting Select A description on setting the jumpers to enable/disable or change functions is illustrated below. Please refer to the diagrams below for jumper locations.  COM3/COM4 Port Setting Select: JP1/JP2

JP1/JP2 Function

1-2 3-4 5-6 7-8 9-10 11-12

RS-232 (Default) Off On

RS-422 On (Term.) On (Term.) Off On On Off

RS-485 On (Term.) On (Term.) On Off On Off y Location:

Universal Remote Control Remote Control (M-855) — JP1/JP2 Function diagram (page 20)
Fig. 16 · JP1/JP2 Function
Page 21 of the Universal Remote Control Remote Control (M-855) user manual — Function JP5
Page 21 · click to enlarge
Page 21
 CPU Type Setting SelectJP3

Function JP3

CPU FSB 400 MHz (Default) 1-2 On

CPU FSB 533 MHz 1-2 Off y Location: Watchdog Timer Setting Select: JP4

Function JP4

NMI 1-2

Reset System (Default) 2-3 y Location:  Clear CMOS Setting Select: JP5

Universal Remote Control Remote Control (M-855) — Function JP4 diagram (page 21)
Fig. 17 · Function JP4

Function JP5

Clear CMOS 2-3 y Location:

Universal Remote Control Remote Control (M-855) — Function JP5 diagram (page 21)
Fig. 18 · Function JP5

Normal (Default) 1-2

Page 22 of the Universal Remote Control Remote Control (M-855) user manual — 2.4 Connector Descriptions
Page 22 · click to enlarge
Page 22
 Power Management Setting SelectJP6

Function JP6

APM Mode (Default) Off y Location:

2.4 Connector Descriptions

Universal Remote Control Remote Control (M-855) — 2.4 Connector Descriptions diagram (page 22)
Fig. 19 · 2.4 Connector Descriptions
Figure 9Connector Locations

ACPI Mode On

Page 23 of the Universal Remote Control Remote Control (M-855) user manual — Function JP6
Page 23 · click to enlarge
Page 23

Table for Connector’s Location Description: Use the information in the following table to change the connector.

Connectors Functions CN1 CRT VGA Port Connector CN2 COM1 RS-232 Serial Port Connector CN3 Parallel Port Connector CN4 USB 0/1 Connectors CN5 Audio Port Connector (Optional) CN6 PS/2 Keyboard & Mouse Connectors CN7 Gigabit Ethernet RJ-45 & USB 2/3 Connectors CN8 External Keyboard & Mouse Connector CN9 CD-IN Connector CN13 COM3 RS-232/422/485 Serial Port Connectors CN14 COM4 RS-232/422/485 Serial Port Connectors CN15 CPU Fan Power Connector CN16 COM2 RS-232 Serial Port Connector CN17 18/24 Bits LVDS Panel Interface CN18 System Fan Power Connector CN19 USB 4/5 (Pin-Header) Connector CN20 System Panel Indicate Connector CN21 Secondary IDE Connector CN22 ATX Power Connector CN23 Primary IDE Connector CN24 Floppy Disk Connector CN25 LINE OUT Connector JP7 LAN LED Connector SATA1 S-ATA1 Connector SATA2 S-ATA2 Connector CF II Type II CompactFlash™ Connector

Page 24 of the Universal Remote Control Remote Control (M-855) user manual — CRT VGA Port Connector (D-SUB 15-pins Female): CN1
Page 24 · click to enlarge
Page 24

CRT VGA Port Connector (D-SUB 15-pins Female): CN1

Universal Remote Control Remote Control (M-855) — CRT VGA Port Connector (D-SUB 15-pins Female): CN1 diagram (page 24)
Fig. 20 · CRT VGA Port Connector (D-SUB 15-pins Female): CN1
15 DCK y FigureCOM1 RS-232 Serial Port Connector (D-Sub 9-pins Male): CN2
Universal Remote Control Remote Control (M-855) — CRT VGA Port Connector (D-SUB 15-pins Female): CN1 diagram (page 24)
Fig. 21 · CRT VGA Port Connector (D-SUB 15-pins Female): CN1

1 DCD (Data Carrier Detect) 6 DSR (Data Set Ready)

2 RXD (Receive Data) 7 RTS (Request to Send)

3 TXD (Transmit Data) 8 CTS (Clear to Send)

4 DTR (Data Terminal Ready) 9 RI (Ring Indicator)

Page 25 of the Universal Remote Control Remote Control (M-855) user manual — Parallel Port Connector (D-Sub 25-pins Male): CN3
Page 25 · click to enlarge
Page 25

Parallel Port Connector (D-Sub 25-pins Male): CN3

Universal Remote Control Remote Control (M-855) — Parallel Port Connector (D-Sub 25-pins Male): CN3 diagram (page 25)
Fig. 22 · Parallel Port Connector (D-Sub 25-pins Male): CN3

13 Select 26 N/A y Figure: USB 0/1 Connectors (4-pins Female): CN4

Universal Remote Control Remote Control (M-855) — Parallel Port Connector (D-Sub 25-pins Male): CN3 diagram (page 25)
Fig. 23 · Parallel Port Connector (D-Sub 25-pins Male): CN3
Page 26 of the Universal Remote Control Remote Control (M-855) user manual — Audio Port Connector (Audio Phone–Jack): CN5 (Optional)
Page 26 · click to enlarge
Page 26

Audio Port Connector (Audio Phone–Jack): CN5 (Optional)

Universal Remote Control Remote Control (M-855) — Audio Port Connector (Audio Phone–Jack): CN5 (Optional) diagram (page 26)
Fig. 24 · Audio Port Connector (Audio Phone–Jack): CN5 (Option…
Red Mic-In y FigurePS/2 Keyboard Connector (6-pins Green Mini Din): CN6
Universal Remote Control Remote Control (M-855) — Audio Port Connector (Audio Phone–Jack): CN5 (Optional) diagram (page 26)
Fig. 25 · Audio Port Connector (Audio Phone–Jack): CN5 (Option…

5 Keyboard Clock 6 NC y Figure: PS/2 Mouse Connector (6-pins Purple Mini Din): CN6

Universal Remote Control Remote Control (M-855) — Audio Port Connector (Audio Phone–Jack): CN5 (Optional) diagram (page 26)
Fig. 26 · Audio Port Connector (Audio Phone–Jack): CN5 (Option…
Page 27 of the Universal Remote Control Remote Control (M-855) user manual — Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack): CN7
Page 27 · click to enlarge
Page 27

Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack): CN7

Universal Remote Control Remote Control (M-855) — Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack): CN7 diagram (page 27)
Fig. 27 · Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack):…

4 NC 8 NC y Figure:  USB 2/3 Connector (4-pins Female): CN7

Universal Remote Control Remote Control (M-855) — Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack): CN7 diagram (page 27)
Fig. 28 · Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack):…

4a Ground 4b Ground y Figure: External Keyboard & Mouse Connector (6-pins Pin-Header): CN8

Universal Remote Control Remote Control (M-855) — Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack): CN7 diagram (page 27)
Fig. 29 · Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack):…

5 Ground 6 VCC y Figure:

Universal Remote Control Remote Control (M-855) — Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack): CN7 diagram (page 27)
Fig. 30 · Gigabit Ethernet RJ-45 Connector (RJ-45 Phone–Jack):…
Page 28 of the Universal Remote Control Remote Control (M-855) user manual — 11 TXD+ 12 TXD-
Page 28 · click to enlarge
Page 28

CD_IN Connector: CN9

Pin # Assignment

2 CD_GND

3 CD_GND

4 CD_IN_Right y FigureCOM3 RS-232/422/485 Serial Port Connectors (14-pins Pin-Header): CN13
Universal Remote Control Remote Control (M-855) — CD_IN Connector: CN9 diagram (page 28)
Fig. 31 · CD_IN Connector: CN9

Pin # Assignment Pin # Assignment

1 DCD 2 RXD

3 TXD 4 DTR

5 Ground 6 DSR

7 RTS 8 CTS

9 RI 10 Ground

11 TXD+ 12 TXD-

13 RXD+ 14 RXD- y COM3 Figure:

1 CD_IN_Left

Page 29 of the Universal Remote Control Remote Control (M-855) user manual — 11 TXD+ 12 TXD-
Page 29 · click to enlarge
Page 29

COM4 RS-232/422/485 Serial Port Connectors (14-pins Pin-Header): CN14

Pin # Assignment Pin # Assignment

1 DCD 2 RXD

3 TXD 4 DTR

5 Ground 6 DSR

7 RTS 8 CTS

9 RI 10 Ground

11 TXD+ 12 TXD-

13 RXD+ 14 RXD- y COM4 Figure: Note: How to connect a RS485 device with the COM port ribbon cable? Our Industrial Board encloses a COM port ribbon cable for internal connection. RS422/485 device must connect to downside D-Sub with 5-pin cable and signal indication as below.

Universal Remote Control Remote Control (M-855) — 11 TXD+ 12 TXD- diagram (page 29)
Fig. 32
RS-422/4851: TXD2: TXD+ 3: RXD4: RXD+ 5: GND

For RS-232 Connector · For RS-422/485 Connector

Page 30 of the Universal Remote Control Remote Control (M-855) user manual — CPU Fan Power Connector: CN15
Page 30 · click to enlarge
Page 30

CPU Fan Power Connector: CN15

Universal Remote Control Remote Control (M-855) — CPU Fan Power Connector: CN15 diagram (page 30)
Fig. 33 · CPU Fan Power Connector: CN15

3 Fan Status Signal y Figure: COM2 RS-232 Serial Port Connector (10-pins Pin-Header): CN16

Universal Remote Control Remote Control (M-855) — CPU Fan Power Connector: CN15 diagram (page 30)
Fig. 34 · CPU Fan Power Connector: CN15

5 Ground 10 Ground y Figure: 18/24 Bits LVDS Panel Interface (40-pins Male): CN17 Pin # Assignment Pin # Assignment

Universal Remote Control Remote Control (M-855) — CPU Fan Power Connector: CN15 diagram (page 30)
Fig. 35 · CPU Fan Power Connector: CN15
Page 31 of the Universal Remote Control Remote Control (M-855) user manual — Pin # Assignment
Page 31 · click to enlarge
Page 31

21 Ground 22 Ground

23 YBM1 24 YBM2

25 YBP1 26 YBP2

27 Ground 28 Ground

29 CLKBM 30 YBM3

31 CLKBP 32 YBP3

33 NC 34 +12V

35 NC 36 +12V

37 NC 38 PVCC

39 BKL 40 PVCC y Figure: System Fan Power Connector: CN18

Universal Remote Control Remote Control (M-855) — 29 CLKBM 30 YBM3 diagram (page 31)
Fig. 36

Pin # Assignment

3 Fan Status Signal y Figure:

1 Ground

Page 32 of the Universal Remote Control Remote Control (M-855) user manual — Pin # Assignment Pin # Assignment SPEAKER PWR LED
Page 32 · click to enlarge
Page 32

USB 4/5 Connector (9-pins Pin-Header): CN19

Universal Remote Control Remote Control (M-855) — USB 4/5 Connector (9-pins Pin-Header): CN19 diagram (page 32)
Fig. 37 · USB 4/5 Connector (9-pins Pin-Header): CN19

9 --- 10 NC y Figure: System Panel Indicate Connector: CN20

Universal Remote Control Remote Control (M-855) — USB 4/5 Connector (9-pins Pin-Header): CN19 diagram (page 32)
Fig. 38 · USB 4/5 Connector (9-pins Pin-Header): CN19

Pin # Assignment Pin # Assignment SPEAKER PWR LED

15 RESET- 16 PWRBT- y Figure:

Page 33 of the Universal Remote Control Remote Control (M-855) user manual — Secondary IDE Connector (40-pins 2.54mm Pitch Pin-Header with Housing): CN21
Page 33 · click to enlarge
Page 33

Secondary IDE Connector (40-pins 2.54mm Pitch Pin-Header with Housing): CN21

Universal Remote Control Remote Control (M-855) — Secondary IDE Connector (40-pins 2.54mm Pitch Pin-Header with Housing): CN21 diagram (page 33)
Fig. 39 · Secondary IDE Connector (40-pins 2.54mm Pitch Pin-He…

39 Activity 40 Ground y Figure:

Page 34 of the Universal Remote Control Remote Control (M-855) user manual — ATX Power Connector: CN22
Page 34 · click to enlarge
Page 34

ATX Power Connector: CN22

Universal Remote Control Remote Control (M-855) — ATX Power Connector: CN22 diagram (page 34)
Fig. 40 · ATX Power Connector: CN22

10 +12v 20 +5V y Figure: Primary IDE Connector (40-pins 2.54mm Pitch Pin-Header with Housing): CN23

Universal Remote Control Remote Control (M-855) — ATX Power Connector: CN22 diagram (page 34)
Fig. 41 · ATX Power Connector: CN22
Page 35 of the Universal Remote Control Remote Control (M-855) user manual — ATX Power Connector: CN22
Page 35 · click to enlarge
Page 35

35 Address 0 36 Address 2

37 Chip Select 0 38 Chip Select 1

39 Activity 40 Ground y Figure: Floppy Disk Connector (34-pins 2.54mm Pitch Pin-Header with Housing): CN24

Universal Remote Control Remote Control (M-855) — ATX Power Connector: CN22 diagram (page 35)
Fig. 42 · ATX Power Connector: CN22

33 NC 34 Diskette Change y Figure:

Page 36 of the Universal Remote Control Remote Control (M-855) user manual — Pin # Assignment Pin # Assignment
Page 36 · click to enlarge
Page 36

LINE OUT Connector: CN25

Pin # Assignment

1 LOUT_L

2 AU_GND

3 VCC_5V

4 LOUT_R y FigureLAN LED Connector: JP7

Pin # Assignment Pin # Assignment

1 LINK_LED 2 VCC_3V

3 ACT_LED 4 VCC_3V y Figure:

Universal Remote Control Remote Control (M-855) — Pin # Assignment Pin # Assignment diagram (page 36)
Fig. 43 · Pin # Assignment Pin # Assignment
Page 37 of the Universal Remote Control Remote Control (M-855) user manual — S-ATA1 Connector (9-pins): SATA1
Page 37 · click to enlarge
Page 37

S-ATA1 Connector (9-pins): SATA1

Universal Remote Control Remote Control (M-855) — S-ATA1 Connector (9-pins): SATA1 diagram (page 37)
Fig. 44 · S-ATA1 Connector (9-pins): SATA1
9 Ground y FigureS-ATA2 Connector (9-pins): SATA2

9 1 7 8

Universal Remote Control Remote Control (M-855) — S-ATA1 Connector (9-pins): SATA1 diagram (page 37)
Fig. 45 · S-ATA1 Connector (9-pins): SATA1

9 Ground y Figure:

9 1 7 8

Page 38 of the Universal Remote Control Remote Control (M-855) user manual — CF
Page 38 · click to enlarge
Page 38

Type II CompactFlash™ Connector: CF II

Universal Remote Control Remote Control (M-855) — Type II CompactFlash™ Connector: CF II diagram (page 38)
Fig. 46 · Type II CompactFlash™ Connector: CF II

57 NC 58 NC y Figure:

CF

Page 39 of the Universal Remote Control Remote Control (M-855) user manual — 3.2 Main Menu
Page 39 · click to enlarge
Page 39

Award BIOS Setup

3.1 BIOS Instructions

Award’s ROM BIOS provides a built-in Setup program, which allows the user to modify the basic system configuration and hardware parameters. The modified data will be stored in a battery-backed CMOS, so that data will be retained even when the power is turned off. In general, the information saved in the CMOS RAM will stay unchanged unless there is a configuration change in the system, such as hard drive replacement or a device is added. It is possible for the CMOS battery to fail, which would cause data loss in the CMOS only. If that happens the BIOS settings would need to be reconfigured.

3.2 Main Menu

Once you enter the AwardBIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press to accept and enter the sub-menu.

Page 40 of the Universal Remote Control Remote Control (M-855) user manual — Award BIOS Setup
Page 40 · click to enlarge
Page 40

Phoenix - AwardBIOS CMOS Setup Utility

¾Standard CMOS Feature

¾Advanced BIOS Feature

¾Advanced Chipset Feature

¾Power Management Setup

Save & Exit Setup

¾PC Health Status

EscQuit ↑ ↓ ← → : Select Item
F10Save & Exit Setup

Time, Date, Hard Disk Type….

Note: that a brief description of each highlighted selection appears at the bottom of the screen. Setup Items: The main menu includes the following main setup categories. Recall that some systems may not include all entries. Standard CMOS Features: Use this menu for basic system configuration. See 3.3 for the details. Advanced BIOS Features: Use this menu to set the Advanced Features available on your system. See 3.5 for the details. Advanced Chipset Features: Use this menu to change the values in the chipset registers and optimize your system's performance. See 3.6 for the details. Integrated Peripherals: Use this menu to specify your settings for integrated peripherals. See section 3.7 for the details. Power Management Setup: Use this menu to specify your settings for power management. See 3.8 for the details. PnP / PCI Configuration: This entry appears if your system supports PnP/PCI. See 3.9 for the details. PC Health Status:

Show 8 more labels / short text on this page
¾Frequency/Voltage Control · Load Fail-Safe Defaults · Load Optimized Defaults · ¾Integrated Peripherals · Set Supervisor Password · Set User Password · ¾PnP/PCI Configurations · Exit Without Saving
Page 41 of the Universal Remote Control Remote Control (M-855) user manual — Award BIOS Setup
Page 41 · click to enlarge
Page 41

Use this menu to show your system temperature, speed and voltage status. See 3.10 for the details. Frequency / Voltage Control: Use this menu to specify your settings for frequency/voltage control. See 3.11 for the details. Load Fail-Safe Defaults: Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. See 3.12 for the details. Load Optimized Defaults: Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While Award has designed the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. See 3.13 for the details. Supervisor / User Password: Use this menu to set User and Supervisor Passwords. See 3.14 for the details. Save & Exit Setup: Save CMOS value changes to CMOS and exit setup. See 3.15 for the details. Exit Without Save: Abandon all CMOS value changes and exit setup. See 3.15 for the details. 3.3 Standard CMOS Features

The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes none, one, or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item.

Page 42 of the Universal Remote Control Remote Control (M-855) user manual — Award BIOS Setup
Page 42 · click to enlarge
Page 42

Mon, JUN 7 2004 16:19:20 13579 MB None None None 1.44M, 3.5 in. None EGA/VGA No Errors 640K 515072K 516096K

Date (mm:dd:yy): Time (hh:mm:ss): ¾ IDE Primary Master ¾ IDE Primary Slave ¾ IDE Secondary Master ¾ IDE Secondary Slave

Item Help Menu Level ¾ Change the day, month, year and century

Drive A Drive B

Based Memory Extended Memory Total Memory

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Date: Options MM/DD/YYYY Set the system date. Note that the ‘Day’ automatically changes when you set the date. Time: Options HH : MM : SS Set the system time. IDE Primary Master: Options are in its sub menu (described in 3.4) Press to enter the sub menu of detailed options. IDE Primary Slave: Options are in its sub menu (described in 3.4) Press to enter the sub menu of detailed options. IDE Secondary Master: Options are in its sub menu (described in 3.4) Press to enter the sub menu of detailed options. IDE Secondary Slave: Options are in its sub menu (described in 3.4) Press to enter the sub menu of detailed options. Drive A/ Drive B: Options are None, 360K, 5.25 in/1.2M, 5.25 in/720K, 3.5 in/ 1.44M, 3.5 in/2.88M, 3.5 in. Select the type of floppy disk drive installed in your system.

Standard CMOS Features · Video Halt On

Page 43 of the Universal Remote Control Remote Control (M-855) user manual — Award BIOS Setup
Page 43 · click to enlarge
Page 43

Video: Options EGA/VGA/CGA 40/CGA 80/MONO Select the default video device. Halt On: Options All Errors/No Errors/All, All but Keyboard/All, All but Diskette/All, All but Disk/Key Select the situation in which you want the BIOS to stop the POST process and notify you. Base Memory: Option N/A Displays the amount of conventional memory detected during boot up. Extended Memory: Option N/A Displays the amount of extended memory detected during boot up. Total Memory: Option N/A Displays the total memory available in the system. 3.4 IDE Adapters

The IDE adapters control the hard disk drive. Use a separate sub menu to configure each hard disk drive.

Phoenix - AwardBIOS CMOS Setup Utility

IDE Primary Master IDE HDD Auto-Detection IDE Primary Master Access Mode Capacity Cylinder Head Precomp Landing Zone Sector

Press Enter Auto Auto 13579 MB 26310 16 0 26309 63

Item Help Menu Level ¾¾ To auto-detect the HDD’s size, head... on this channel

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults IDE HDD Auto-Detection: Options Press Enter Press Enter to auto-detect the HDD on this channel. If detection is successful, it fills the remaining fields on this menu.

Page 44 of the Universal Remote Control Remote Control (M-855) user manual — Award BIOS Setup
Page 44 · click to enlarge
Page 44

IDE Primary Master: Options None, Auto and Manual Selecting “Manual” lets you set the remaining fields on this screen. Selects the type of fixed disk. "User Type" will let you select the number of cylinders, heads, etc. Note: PRECOMP=65535 means NONE! Access Mode: Options CHS, LBA, Large and Auto Choose the access mode for this hard disk Capacity: Options Auto Display your disk drive size Disk drive capacity (Approximated). Note that this size is usually slightly greater than the size of a formatted disk given by a disk-checking program. The following options are selectable only if the ‘IDE Primary Master’ item is set to “Manual” Cylinder: Options Min = 0, Max = 65535 Set the number of cylinders for this hard disk. Head: Options Min = 0, Max = 255 Set the number of read/write heads Precomp: Options Min = 0, Max = 65535 **** Warning: Setting a value of 65535 means no hard disk Landing zone: Options Min = 0, Max = 65535 Sector: Options Min = 0, Max = 255 Number of sectors per track

Page 45 of the Universal Remote Control Remote Control (M-855) user manual — Phoenix - AwardBIOS CMOS Setup Utility
Page 45 · click to enlarge
Page 45

3.5 Advanced BIOS Features

This section allows you to configure your system for basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security.

Phoenix - AwardBIOS CMOS Setup Utility

Advanced BIOS Features ¾ CPU Feature ¾ Hard Disk Boot Priority

Press Enter Press Enter Enabled Floppy Hard Disk LS-120 Enabled Disabled Enabled On Fast Disabled 6 250 Setup Non-OS2 No

Item Help Menu Level ¾

Virus Warning CPU L1 Cache CPU L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Gate A20 Option Typematic Rate Setting X Typematic Rate (Chars/Sec) X Typematic Delay (Msec)

Security Option OS Select For DRAM > 64MB

Report No FDD For WIN95

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5Previous Values F6: Fail-safe defaults F7: Optimized Defaults CPU Feature:

Phoenix - AwardBIOS CMOS Setup Utility

Item Help Menu Level ¾¾

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Thermal Management: It allows you to select the thermal Monitor.

The Choice: Thermal monitor1.

CPU Feature · Thermal Monitor 1 · Thermal Management

Page 46 of the Universal Remote Control Remote Control (M-855) user manual — 3.5 Advanced BIOS Features
Page 46 · click to enlarge
Page 46

Hard Disk Boot Priority: Press Enter and It shows Bootable add-in Card. Virus Warning: Allow you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempts to write data into this area, BIOS will show a warning message on screen and alarm beep. Enabled---Activates automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table. Disabled---No warning message will appear when anything attempts to access the boot sector or hard disk partition table. CPU L1& L2 Cache: These two categories speed up memory access. However, it depends on CPU/chipset design. Enabled---Enable cache Disabled---Disable cache Quick Power On Self Test: This category speeds up Power On Self Test (POST) after you power up the computer. If it is set to Enable, BIOS will shorten or skip some check items during POST. Enabled---Enable quick POST Disabled--- Normal POST First/Second/Third Boot Device: The BIOS attempts to load the operating system from the devices in the sequence selected in these items. The choices: Floppy, LS/ZIP, Hard Disk, CDROM, LAN and Disabled. Boot Other Device: When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the first, second, and third boot devices. The choices: Enabled, Disabled Swap Floppy Drive: If the system has two floppy drives, you can swap the logical drive name assignments. The choices: Enabled, Disabled.

Page 47 of the Universal Remote Control Remote Control (M-855) user manual — 3.5 Advanced BIOS Features
Page 47 · click to enlarge
Page 47

Boot Up Floppy Seek: Seeks disk drives during boot up. Disabling speeds boot up. The choices: Enabled, Disabled. Boot Up NumLock Status: Select power on state for NumLock. The choices: On, Off Gate A20 Option: Select if chipset or keyboard controller should control GateA20. Normal---A pin in the keyboard controller controls GateA20 Fast---Lets chipset control GateA20 Typematic Rate Setting: Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The choice: Enabled, Disabled. Typematic Rate (Chars/Sec): Sets the number of times a second to repeat a keystroke when you hold the key down. The choice: 6, 8, 10, 12, 15, 20, 24 and 30. Typematic Delay (Msec): Sets the delay time after the key is held down before it begins to repeat the keystroke. The choice: 250, 500, 750 and 1000. Security Option: Select whether the password is required every time the system boots or only when you enter setup. System---The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt. Setup---The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. Note: To disable security, select PASSWORD SETTING at Main Menu and then you

will be asked to enter password. Do not type anything and just press , it will disable security. Once the security is disabled, the system will boot and you can enter Setup freely. OS Select For DRAM > 64MB:

Page 48 of the Universal Remote Control Remote Control (M-855) user manual — 3.5 Advanced BIOS Features
Page 48 · click to enlarge
Page 48

Select the operating system that is running with greater than 64MB of RAM on the system. The choices: Non-OS2, OS2. Report No FDD For Win 95: Whether report no FDD for Windows 95 or not. The choices: Yes, No. 3.6 Advanced Chipset Features

This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and access to system memory resources, such as DRAM and the external cache. It also coordinates communications between the conventional ISA bus and the PCI bus. It must be stated that these items should never need to be altered. The default settings have been chosen because they provide the best operating conditions for your system. The only time you might consider making any changes would be if you discovered that data was being lost while using your system.

Phoenix - AwardBIOS CMOS Setup Utility

By SPD 2.5 6 3 3 Non-ECC Auto Max 266MHz Enabled Disabled Disabled Enabled 16 Min 64

DRAM Timing Selectable X CAS Latency Time X Active To Precharge Delay X DRAM RAS# To CAS# Delay X DRAM RAS# Precharge

Item Help Menu Level ¾

DRAM Data Integrity Mode

MGM Core Frequency System BIOS Cacheable Video BIOS Cacheable Memory Hole At 15M-16M Delayed Transaction Delay Prior To Thermal AGP Aperture Size (MB)

** On-Chip VGA Setting ** On-Chip VGA On-Chip Frame Buffer Size Boot Display Pannel Number

Enabled 32MB VBIOS Default 1

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5Previous Values F6: Fail-safe defaults F7: Optimized Defaults DRAM Timing Selectable:

Advanced Chipset Features

Page 49 of the Universal Remote Control Remote Control (M-855) user manual — 3.5 Advanced BIOS Features
Page 49 · click to enlarge
Page 49

Select the operating system that is selecting DRAM timing, so select SPD for setting SDRAM timing by SPD. The choices: Manual, By SPD. CAS Latency Time: When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The choices: 2, 2.5. Active To Precharge Delay: Select the operating system that is active to precharge delay. The choices: 5, 6, 7. DRAM RAS# To CAS# Delay: This field lets you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The choices: 2, 3. DRAM RAS# Precharge: If an insufficient number of cycles are allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain data. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The choices: 2, 3. DRAM Data Integrity Mode: This item shows you if the DRAM has ECC or not. The choices: Non-ECC, ECC. MGM Core Frequency: This item allows you to determine the MGM core frequency. The choices: Auto Max 266MHz, 400/266/133/200MHz,

400/200/100/200MHz, 400/200/100/133MHz, 400/266/133/267MHz, 400/333/166/250MHz, Auto Max 400/333. System BIOS Cacheable: Selecting “Enabled” allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result.

Page 50 of the Universal Remote Control Remote Control (M-855) user manual — 3.5 Advanced BIOS Features
Page 50 · click to enlarge
Page 50

The choices: Enabled, Disabled. Video BIOS Cacheable: Select “Enabled” allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The choices: Enabled, Disabled. Memory Hole At 15M-16M: You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements. The choices: Enabled, Disabled. Delayed Transaction: The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select “Enabled” to support compliance with PCI specification version 2.2. The choices: Enabled, Disabled. Delay Prior To Thermal: Select this item allows the delay prior to thermal time. The choices: 4Min, 8Min, 16Min and 32Min. AGP Aperture Size (MB): This field determines the effective size of the Graphic Aperture used for a particular GMCH configuration. It can be updated by the GMCH-specific BIOS configuration sequence before the PCI standard bus enumeration sequence takes place. If it is not updated then a default value will select an aperture of maximum size. The choices: 4, 8, 16, 32, 64, 128 and 256.

**On-Chip VGA Setting** On-Chip VGA: This item allows you to control the on-chip VGA. The choices: Enabled, Disabled. On-Chip Frame Buffer Size: This item allows you to control the on-chip frame buffer size. The choices: 1M, 4M, 8M, 16M and 32M. Boot Display: This item allows you to select the boot display device.

Page 51 of the Universal Remote Control Remote Control (M-855) user manual — F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Onboard IDE Device:
Page 51 · click to enlarge
Page 51

The choices: VBIOS Default, CRT, LFP and CRT+LEP. Panel Number: This item allows you to select the panel resolution. The choices: 1-8. 3.7 Integrated Peripherals

Phoenix - AwardBIOS CMOS Setup Utility

Integrated Peripherals ¾ Onboard IDE Device ¾ Onboard Device ¾ SuperIO Device

Press Enter Press Enter Press Enter Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ10 2E8 IRQ11

Item Help Menu Level ¾ If your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of block read/write per sector the drive can support

Onboard Lan Boot ROM Onboard Serial Port 1 Serial Port 3 Use IRQ Onboard Serial Port 2 Serial Port 4 Use IRQ Onboard Serial Port 3 Serial Port 3 Use IRQ Onboard Serial Port 4 Serial Port 4 Use IRQ

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Onboard IDE Device:

Onboard IDE Device On-Chip Primary PCI IDE IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA On-Chip Secondary PCI IDE IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA IDE Secondary Slave UDMA IDE HDD Block Mode

Enabled Auto Enabled Auto Enabled

Item Help Menu Level ¾ If your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of block read/write per sector the drive can support

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5Previous Values F6: Fail-safe defaults F7: Optimized Defaults
Page 52 of the Universal Remote Control Remote Control (M-855) user manual — Onboard Device
Page 52 · click to enlarge
Page 52

OnChip Primary/Secondary PCI IDE: The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select “Enabled” to activate each channel separately. The choices: Enabled, Disabled. IDE Primary/Secondary Master/Slave PIO: The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. The choices: Auto, Mode 0, Mode 1, Mode 2, Mode 3 and Mode 4. IDE Primary/Secondary Master/Slave UDMA: Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/33, select “Auto” to enable BIOS support. The choices: Auto, Disabled. IDE HDD Block Mode: Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. The choices: Enabled, Disabled Onboard Device:

Onboard Device

Enabled Enabled Disabled Disabled Auto Onboard/AGP

USB Controller USB 2.0 Controller USB Keyboard Support USB Mouse Support AC97 Audio Init Display First

Item Help Menu Level ¾

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults USB / USB 2.0 Controller: Select “Enabled” if your system contains a Universal Serial Bus (USB) / USB 2.0 controller and you have USB peripherals. The choices: Enabled, Disabled.

Page 53 of the Universal Remote Control Remote Control (M-855) user manual — SuperIO Device
Page 53 · click to enlarge
Page 53

USB Keyboard Support: Select “Enabled” if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The choices: Enabled, Disabled. USB Mouse Support: Select “Enabled” if your system contains a Universal Serial Bus (USB) controller and you have a USB mouse. The choices: Enabled, Disabled. AC97 Audio: This item allows you to decide to auto or disable the chipset family to support AC97 Audio. The choices: Auto, Disabled. Init Display First: This item allows you to decide to active whether PCI Slot or on-chip VGA first. The choices: PCI Slot, Onboard/AGP. SuperIO Device:

SuperIO Device

BUTTON ONLY Enter Ctrl-F1 Enabled 378/IRQ7 SPP EPP1.7 3 Off

Power ON Function X KB Power ON Password X Hot Key Power ON

Item Help Menu Level ¾

Onboard FDC Controller Onboard Parallel Port Parallel Port Mode X EPP Mode Select X ECP Mode Use DMA

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Power On Function: You can use this item to select operating Power On the system. The choices: Password, Hot KEY, Any KEY, BUTTON ONLY,

PWRON After PWR-Fail · Keyboard 98

Page 54 of the Universal Remote Control Remote Control (M-855) user manual — SuperIO Device
Page 54 · click to enlarge
Page 54

KB Power ON Password: You can use this item to limit operating KB Power On system. The choice: Enter Hot Key Power ON: You can use this item to select operating Hot Key to Power On system. The choices: Ctrl-F1~Ctrl-F12. Onboard FDC Controller: Select “Enabled” if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install and-in FDC or the system has no floppy drive, select Disabled in this field. The choices: Enabled, Disabled. Onboard Parallel Port: This item allows you to determine access onboard parallel port controller with which I/O address. The choices: 3BC/IRQ7, 378/IRQ7, 278/IRQ5 and Disabled. Parallel Port Mode: Select an operating mode for the onboard parallel (printer) port. Select Normal, Compatible, or SPP unless you are certain your hardware and software both support one of the other available modes. The choices: SPP, EPP, ECP and ECP+EPP. EPP Mode Select: Select EPP port type 1.7 or 1.9. The choices: EPP1.7, 1.9. ECP Mode Use DMA: Select a DMA channel for the parallel port for use during ECP mode. The choices: 3, 1. PWRON After PWR-Fail: This item allows you to select if you want to power on the system after power failure. The choices: Off, On and Former-Sts. Onboard Lan Boot ROM: Select “Enabled” if your system has a LAN device installed on the system board and you wish to use it. The choices: Enabled, Disabled.

Page 55 of the Universal Remote Control Remote Control (M-855) user manual — SuperIO Device
Page 55 · click to enlarge
Page 55

Onboard Serial Port 1/Port 2: Select an address for the first and second serial ports. Serial Port 1/Port 2 Use IRQ: Select an IRQ for the first and second serial ports. Onboard Serial Port 3/Port 4: Select an address for the third and forth serial ports. Serial Port 3/Port 4 Use IRQ: Select an IRQ for the third and forth serial ports. 3.8 Power Management Setup

The Power Management Setup allows you to configure you system to most effectively save energy while operating in a manner consistent with your own style of computer use.

Phoenix - AwardBIOS CMOS Setup Utility

Enabled User Define DPMS Yes Stop Grant Disabled Disabled 50.0% Enabled Disabled 0 0 : 0 : 0 Disabled

ACPI Function Power Management Video Off Method Video Off In Suspend Suspend Type Suspend Mode HDD Power Down CPU THER-Throttling Wake-Up by PCI card Resume by Alarm X Date (of Month) Alarm

Item Help Menu Level ¾

X Time (hh:mm:ss) Alarm ** Reload Global Timer Events ** Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD, COM, LPT Port PCI PIRQ [A-D]#

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5Previous Values F6: Fail-safe defaults F7: Optimized Defaults ACPI Function:

Power Management Setup

Page 56 of the Universal Remote Control Remote Control (M-855) user manual — SuperIO Device
Page 56 · click to enlarge
Page 56

This item allows you to enable or disable the Advanced Configuration and Power Management (ACI). The choices: Enabled, Disabled. Power Management: This category allows you to select the type (or degree) of power saving and is directly related to the following modes: 1. HDD Power Down 2. Doze Mode 3. Suspend Mode

Min. Power Saving: Minimum power management. Doze Mode = 1 hr., Standby Mode = 1 hr., Suspend Mode = 1 hr., and HDD Power Down = 15 min.

Max. Power Saving: Maximum power management -- ONLY AVAILABLE FOR SL CPU’s. Doze Mode = 1 min., Standby Mode = 1 min., Suspend Mode = 1 min., and HDD Power Down = 1 min.

User Defined: Allow you to set each mode individually. When not disabled, each of the ranges is from 1 min. to 1 hr. except for HDD Power Down, which ranges from 1 min. to 15 min. and disable. Video Off Method: This determines the manner in which the monitor is blanked.

V/H SYNC+Blank: This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer.

Blank Screen: This option only writes blanks to the video buffer.

DPMS: Initial display power management signaling. Video Off In Suspend: This determines the manner in which the monitor is blanked. The choices: Yes, No.

Page 57 of the Universal Remote Control Remote Control (M-855) user manual — SuperIO Device
Page 57 · click to enlarge
Page 57

Suspend Type: Select the Suspend Type. The choices: PWRON Suspend, Stop Grant. Suspend Mode: When “Enabled” and after the set time of system inactivity. All devices except the CPU will be shut off. The choices: Enabled, Disabled. HDD Power Down: When “Enabled” and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active. The choices: Enabled, Disabled. CPU THER-Throttling: Select the CPU THRM-Throttling rate. The choices: 12.5%, 25.0%, 37.5%, 50.0%, 62.5%, 75.0% and 87.5%. Wake-Up by PCI Card: An input signal from PME on the PCI card awakens the system from a soft off state. The choices: Enabled, Disabled. Resume by Alarm: When “Enabled”, your can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend mode. The choices: Enabled, Disabled. PM Events: PM events are I/O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode. In effect, the system remains alert for anything, which occurs to a device, which is configured as Enabled, even when the system is in a power down mode. Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD, COM, LPT Port PCI PIRQ [A-D] #

Page 58 of the Universal Remote Control Remote Control (M-855) user manual — 3.9 PnP/PCI Configurations
Page 58 · click to enlarge
Page 58

3.9 PnP/PCI Configurations

This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

Phoenix - AwardBIOS CMOS Setup Utility

Disabled Auto (ESCD) Press Enter Disabled

Reset Configuration Data Resources Controlled By X IRQ Resources

Item Help Menu Level ¾

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Reset Configuration Data: Normally, you leave this field Disabled. Select “Enabled” to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot. The choices: Enabled, Disabled. Resources Controlled By: It allows you can automatically configure all the boot and Plug and Play-compatible devices. If you select Auto, all the interrupt request (IRQ) and DMA assignment fields disappear, as the BIOS automatically assigns them. IRQ Resources: When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. PCI/VGA Palette Snoop: Leave this field at “Disabled”. The choices: Enabled, Disabled.

PnP/PCI Configurations · PCI/VGA Palette Snoop

Page 59 of the Universal Remote Control Remote Control (M-855) user manual — 3.10 PC Health Status
Page 59 · click to enlarge
Page 59

3.10 PC Health Status

Phoenix - AwardBIOS CMOS Setup Utility

PC Health Status CPU Warning Temperature SYS Temperature CPU Temperature CPU FAN SYSFAN VDIMM VCORE +3.3 + 5 V +12 V -12 V - 5 V VBAT (V) 5VSB (V) Shutdown Temperature

Disabled 32°C / 89°F 28°C / 82°F 5152RPM 3283RPM 2.48 4.42V 3.34V 4.94V 11.85V -12.28V -4.99V 3.02V 5.04V Disabled

Item Help Menu Level ¾

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults CPU Warning Temperature: This item will prevent CPU from overheating. The choices: 50°C /122°F ~70°C /158°F, Disabled. SYS Temperature: Displays the current system temperature. CPU Temperature: Displays the current CPU temperature. CPUFAN: Displays the current CPU fan operating speed. SYSFAN: Displays the current system fan operating speed. VDIMM: Displays the voltage level of the DRAM. VCORE: Displays the voltage level of CPU (Vcore).

Page 60 of the Universal Remote Control Remote Control (M-855) user manual — 3.9 PnP/PCI Configurations
Page 60 · click to enlarge
Page 60

+3.3V/+5V/+12V/-12V/-5V/5VSB(V): Displays the voltage of +5V/+12V/-12V/-5V. VBAT (V): Displays the voltage level of the battery. Shutdown Temperature: This item allows you to set up the CPU shutdown Temperature. This item is only effective under Windows® 98 ACPI mode. The choices: Disabled, 60°C / 140°F, 65°C / 149°F, 70°C / 159°F and 75°C / 167°F. 3.11 Frequency/Voltage Control

Phoenix - AwardBIOS CMOS Setup Utility

Frequency/Voltage Control Auto Detect PCI CLK Spread Spectrum

Item Help Menu Level ¾

↑↓→← Move EnterSelect +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults Auto Detect PCI CLK: When “Enabled”, this item will auto detect if the PCI slot have devices and will send clock signal to PCI devices. When disabled, it will send the clock signal to PCI slot. The choices: Enabled, Disabled. Spread Spectrum: This item allows you to enable or disable the Spread Spectrum. The choices: Disabled, -0.25%, -0.50% and -0.75%. 3.12 Load Fail-Safe Defaults

When you press on this item you get a confirmation dialog box with a message similar to:

Enabled Disabled

Page 61 of the Universal Remote Control Remote Control (M-855) user manual — 3.9 PnP/PCI Configurations
Page 61 · click to enlarge
Page 61

Load Fail-Safe Defaults (Y/N)? N Pressing ‘Y’ loads the BIOS default values for the most stable, minimal-performance system operations. 3.13 Load Optimized Defaults

When you press on this item you get a confirmation dialog box with a message similar to: Load Optimized Defaults (Y/N)? N Pressing ‘Y’ loads the default values that are factory settings for optimal performance system operations. 3.14 Supervisor/User Password Setting

You can set either supervisor or user password, or both of then. The differences between are: Set Supervisor Password: can enter and change the options of the setup menus. Set User Password: just can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password.

ENTER PASSWORD: Type the password, up to eight characters in length, and press . The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press . You may also press to abort the selection and not enter a password. To disable a password, just press when you are prompted to enter the password. A message will confirm the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely.

Page 62 of the Universal Remote Control Remote Control (M-855) user manual — 3.9 PnP/PCI Configurations
Page 62 · click to enlarge
Page 62

PASSWORD DISABLED. When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer. You determine when the password is required within the BIOS Features Setup Menu and its Security option (see Section 3). If the Security option is set to “System”, the password will be required both at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup. 3.15 Exiting BIOS Setup

Save & Exit Setup Pressing on this item asks for confirmation:

Save to CMOS and EXIT (Y/N)? Y Pressing “Y” stores the selections made in the menus in CMOS – a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS. After saving the values the system is restarted again. Exit Without Saving Pressing on this item asks for confirmation:

Quit without saving (Y/N)? Y This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect. This exits the Setup utility and restarts your computer.

Page 63 of the Universal Remote Control Remote Control (M-855) user manual — Warranty Policy
Page 63 · click to enlarge
Page 63

Warranty Policy

Thank you for choosing ADLINK. To understand your rights and enjoy all the after-sales services we offer, please read the following carefully. 1. Before using ADLINK’s products please read the user manual and follow the instructions exactly. When sending in damaged products for repair, please attach an RMA application form which can be downloaded from: http://rma.adlinktech.com/policy/

  • 2. All ADLINK products come with a limited two-year warranty, one year for products bought in China.
  • The warranty period starts on the day the product is shipped from ADLINK’s factory.
  • Peripherals and third-party products not manufactured by ADLINK will be covered by the original manufacturers' warranty.
  • For products containing storage devices (hard drives, flash cards, etc.), please back up your data before sending them for repair. ADLINK is not responsible for any loss of data.
  • Please ensure the use of properly licensed software with our systems. ADLINK does not condone the use of pirated software and will not service systems using such software. ADLINK will not be held legally responsible for products shipped with unlicensed software installed by the user.
  • For general repairs, please do not include peripheral accessories. If peripherals need to be included, be certain to specify which items you sent on the RMA Request & Confirmation Form. ADLINK is not responsible for items not listed on the RMA Request & Confirmation Form. 3. Our repair service is not covered by ADLINK's guarantee in the following situations:
  • Damage caused by not following instructions in the User's Manual.
  • Damage caused by carelessness on the user's part during product transportation.
  • Damage caused by fire, earthquakes, floods, lightening, pollution, other acts of God, and/or incorrect usage of voltage transformers.
  • Damage caused by inappropriate storage environments such as with high temperatures, high humidity, or volatile chemicals.
  • Damage caused by leakage of battery fluid during or after change of batteries by customer/user.
  • Damage from improper repair by unauthorized ADLINK technicians.
  • Products with altered and/or damaged serial numbers are not entitled to our service.
  • This warranty is not transferable or extendible.
  • Other categories not protected under our warranty. 4. Customers are responsible for all fees necessary to transport damaged products to ADLINK.

For further questions, please e-mail our FAE staff: service@adlinktech.com

Warranty Policy • 57

Ask about the Universal Remote Control Remote Control (M-855)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Universal Remote Control Remote Control (M-855)

Be the first to ask — other owners or our team will answer.

Original document

Universal Remote Control Remote Control (M-855) manual PDF

63 pages·930 KB·Remote Control·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…