Instruction/ maintenance manual of the product 1050 White Rodgers
Go to page of 10
WHITE-RODGERS DIVISION EMERSON ELECTRIC CO. 9797 REAVIS RD., ST. LOUIS, MO. 63123 (314) 577-1300, FAX (314) 577-1517 9999 HWY. 48, MARKHAM, ONT. L3P 3J3 (905) 475-4653, FAX (905) 475-4625 Printed in U.
2 INST ALLA TION NOTE Use care not to bend or dent either of the sensing bulbs Both the outdoor bulb and inside bulb should be installed before the control case, since capillary lengths of these bulbs will normally determine the final location for the control case.
3 WIRING & OPERA TION CONT . THERM PILOT TRANS T T CONNECTIONS TO CIRCULATOR Circulator Operation 1. Unzoned Systems, or Circulator-Zoned Systems — The thermostat cycles the circulator motor (through a relay) to meet the demand for heating.
4 DIAL SETTINGS When using this control as an exact replacement, use same dial settings as for old control. A. SETTING THE ROUND DIAL: Set the round dial for “N” initially. This will enable minor additional adjustments to be made later if the specific instal- lation should require it (refer to “C”.
5 DIAL SETTINGS CONT . D. ADDITIONAL INFORMATION: Charts 1, 2, and 3 show the effect which dial settings have upon boiler water temperature under varying outside air temperatures.
WHITE-RODGERS DIVISION EMERSON ELECTRIC CO. 9797 REAVIS RD., ST. LOUIS, MO. 63123 (314) 577-1300, TÉLÉCOPIEUR (314) 577-1517 9999 HWY. 48, MARKHAM, ONT.
2 INST ALLA TION NOTE Prendre soin de ne pas plier ou bosseler les capteurs. Les capteurs intérieur et extérieur doivent tous les deux être installés avant le boîtier de commande, puisque c’est la longueur des tubes capillaires qui déterminera généralement l’emplacement du boîtier.
3 TYPE 809 RELAY CIRCULATOR MOTOR LINE HOT N 1 2 L L TRANSFORMER HOT LINE N 4 5 6 4 5 6 4 5 6 4 5 6 4 5 6 1 2 3 4 5 2 6 1 2 3 4 5 2 6 1 2 3 4 5 2 6 1 2 3 4 5 2 6 1 2 3 4 5 2 6 ADDITIONAL ZONES CÂBLAG.
4 AJUSTEMENT SUGGÉRÉ Hausser le réglage du cadran carré. Abaisser le réglage du cadran carré. Hausser le réglage du cadran rond. (Hausser aussi le cadran carré si le cadran rond est réglé au plus chaud.) Abaisser le réglage du cadran rond. (Abaisser aussi le cadran carré si nécessaire.
5 RÉGLAGE DES POINTS DE CONSIGNE (suite) D. RENSEIGNEMENTS SUPPLÉMENTAIRES : Les graphiques 1, 2 et 3 illustrent l’effet des points de consigne des cadrans sur la température de l’eau.
An important point after buying a device White Rodgers 1050 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought White Rodgers 1050 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data White Rodgers 1050 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, White Rodgers 1050 you will learn all the available features of the product, as well as information on its operation. The information that you get White Rodgers 1050 will certainly help you make a decision on the purchase.
If you already are a holder of White Rodgers 1050, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime White Rodgers 1050.
However, one of the most important roles played by the user manual is to help in solving problems with White Rodgers 1050. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device White Rodgers 1050 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
